Page 1 E1000 series 8CH Pure NVR(E1008) 8CH Hybrid DVR(E1008H) User Manual V2.3.1.1...
Page 2 The information contained in this documentation is subject to change without notice. In no event will AVer Information Inc. be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use this product or documentation, even if advised of the possibility of such damages.
Page 3 © 2014 AVer Information Inc. All rights reserved. All rights of this object belong to AVer Information Inc. Reproduced or transmitted in any form or by any means without the prior written permission of AVer Information Inc. is prohibited. All information or specifications are subject to change without prior notice.
Page 4: Table Of Contents
Contents CHAPTER 1 HARDWARE INTRODUCTION ............ 1 Package Contents ..................1 1.1.1 E1008 ....................1 1.1.2 E1008H ................... 1 Front Panel ....................2 Back Panel ....................3 1.3.1 E1008 ....................3 1.3.2 E1008H ................... 4 Hard Disk Installation ................5 Pin Definition of Sensor/Relay/RS485 Port ..........
Page 5 2.5.2.1 Daylight Saving Time Setting ..........29 2.5.2.2 Customizing System Login Setting ........30 2.5.3.3 Customizing System Miscellaneous Setting ....... 31 2.5.4 Update/Export/Import ..............32 2.5.4.1 Import the NVR/DVR System Configuration ....... 33 2.5.4.2 Export the NVR/DVR System Configuration ....... 35 2.5.4.3 Upgrade the NVR/DVR Firmware ........
Page 6 2.8.2.1 Active IP Function .............. 58 2.8.3 Camera Detail Configuration ............60 Info ..................60 Basic .................. 61 Preference ................62 Exposure ................64 Stream ................65 ROI ..................66 Smart Stream ..............67 Privacy Mask ..............68 Motion Detection ..............69 IVA ..................
Page 7 2.13.1 Create the User Account ............. 105 2.13.2 Delete the User Account .............. 108 2.14 I/O Setting .................... 109 2.14.1 Sensor Setting ................109 2.14.2 Relay Setting ................110 2.15 Emap Setting ..................111 2.15.1 Setup the Emap ................111 2.16 iPOS Setting ..................114 2.17 Log Viewer ...................
Page 8 View the Emap ..................135 Snapshot the Screen ................136 Full Screen Display ................137 3.10 Hide the Camera List ................138 3.11 Auto Display Channel in Cycle ............. 139 3.12 Enable/Disable 2-Way Audio Function ..........140 CHAPTER 4 PLAYBACK RECORDED VIDEO ON NVR/DVR SYSTEM ..141 Playback on NVR/DVR System ............
Page 9 CHAPTER 6 USING THE PCVIEWER ............164 Familiarizing Functions of Preview Mode ..........165 Familiarizing Functions of Playback Mode ........... 166 Appendix Recovery NVR/DVR System through the USB port ......168 WARRANTY NOTICE ................... 170...
Page 10: Chapter 1 Hardware Introduction
Chapter 1 Hardware Introduction Package Contents 1.1.1 E1008 E1008 NVR unit USB optical mouse Power adaptor Software CD Power cable Manual CD HDD holder & screws 1.1.2 E1008H E1008H DVR unit USB optical mouse Power adaptor Software CD Power cable Manual CD Video in cable (included 8 audio in cables)
Page 11: Front Panel
Front Panel ○ ○ Recording status indicator Foot rubber ○ ○ System power indicator USB port ○ ○ USB port Foot rubber...
Page 12: Back Panel
Back Panel 1.3.1 E1008 ○ ○ MIC input port RS485 port ○ ○ Audio output port Sensor input port ○ ○ LAN1/LAN2 port Alarm(relay)output port ○ ○ USB port Power connector port ○ ○ HDMI port e-SATA port ○ ○ TV output port VGA output port...
Page 13: E1008H
1.3.2 E1008H ○ ○ MIC input port RS485 port ○ ○ Audio output port Sensor input port ○ ○ LAN1/LAN2 port Alarm(relay)output port ○ ○ USB port Power connector port ○ ○ HDMI port e-SATA port ○ ○ TV output port VGA output port ○...
Page 14: Hard Disk Installation
Hard Disk Installation The NVR/DVR unit supports 1 SATA hard disks inside of NVR/DVR unit. Follow the illustrated instructions below to install the hard disk: 1. Loosen all screws(2 sides and rear side) 2. Push the cover backward and lift. Please be careful of hands.
Page 15: Pin Definition Of Sensor/Relay/Rs485 Port
Pin Definition of Sensor/Relay/RS485 Port The I/O card enables you to connect 4 sensor inputs and 4 relay outputs. Just connect the external sensor and relay pin directly to the I/O card pinhole. Check the table below and locate which pinhole is assigned to sensor input and relay output. The signal from the sensor (i.e., infrared sensors, smoke detectors, proximity sensors, door sensors, etc.) is being transmitted to the I/O card and this triggers the system to respond and send signal to relay device (i.e., alarm, telephone etc).
Page 16  Sensor Pin definition Definition Sensor Signal 1 Sensor Signal 2 Sensor Signal 3 Sensor Signal 4 Sensor Ground Signal  Alarm Pin definition Definition Relay Common 1 Relay Normal Open Relay Normal Close Relay Common 2 Relay Normal Open Relay Normal Close...
Page 17: Chapter 2 Main System Configuration
Chapter 2 Main System Configuration Getting Started 1. Connect the power cable and mouse to NVR/DVR unit. 2. Power on the NVR/DVR unit and wait for NVR/DVR system start up processing to complete. 3. For security purpose, the NVR/DVR system would require user to enter User ID and Password before it can be accessed.
Page 18: Familiarizing Icons On Dialog Box
 Setup System Date and Time: Setup the date and time in order to have corrected recording time and date. Please refer to Chapter 2.5.1.  Format Hard Disk: The hard disk must be formatted before use it to save recording data (see also Chapter 2.7.1).
Page 19: Familiarizing Functions In Preview Mode
Familiarizing Functions in Preview Mode (9) (10) (11) (12) (13) (14)(15) (16) (17) Name Function Click Setup button to configure settings for cameras, recording, (1) Setup network, schedule, backup, sensors, relays, alarms and user authentication. Switch to Preview mode. This allows you to view live camera (2) Preview display.
Page 20 Name Function (7) POS Log Viewer Search and display POS event logs (see also Chapter 2.17.3). (8) Date and Time It shows the current system date and time. Switch to Playback mode. This allows you to view the recorded (9) Playback video file.
Page 21 Name Function (16) Power button Call up the Power dialog box. In the Power dialog box, user may do the following: Exit: To shutdown the NVR/DVR system. Compact: Switch to compact mode. In compact mode, user’s authority is limited (see also Chapter 2.4.1).
Page 22: Familiarizing Functions In Playback Mode
Familiarizing Functions in Playback Mode Click playback tab to switch to playback mode. (11) (12) (13) (14) (15) (16) (17)(18) (19) (20) (21) (22) (23) (24) (25) (10) (26) Name Function Click Setup button to configure settings for cameras, recording, (1) Setup network, scheduler, backup, sensors, relays, alarms and user authentication.
Page 23 Name Function NVR/DVR supports 2 type of searching in playback mode – (6) Search Event Search and Visual Search. - Event Search: Search from the recorded activities that were recorded in event log such as Sensor, Motion, Video Loss (see also Chapter 4.
Page 24 Name Function (10) Date and Time It shows the current date and time. Switch to Playback mode. This allows you to view the recorded (11) Playback video file. To hide the side area and give more view of screen. (12) Hide button (13) Split Screen Mode Select from 4 kinds of split screen type to playback the recorded video file of all the camera, or one camera over the other or...
Page 25 Name Function Click it to view NVR/DVR system’s version and copyright. (18) System Information (19) Power button Call up the Power dialog box. In the Power dialog box, user may do the following: Exit: To shutdown the NVR/DVR system. Compact: Switch to compact mode. In compact mode, user’s authority is limited (see also Chapter 2.4.2).
Page 26 Name Function From left to right order: (23) Playback Control Buttons Previous: Go back to the previous frame. Slower: Play the recorded video file at the speed of 1/2x, 1/4x, or 1/8x. The playback speed will show on the screen. Rewind: Wind back the recorded video file.
Page 27: Compact Mode
Compact Mode The preview and playback are both supported compact mode. To switch to Compact mode, click power button (located at upper right corner) and select Compact button in Power dialog in preview or playback mode. To switch back to Advance mode, click power button and select Advance button in preview or playback mode.
Page 28: Familiarizing Functions In Preview Compact Mode
2.4.1 Familiarizing Functions in Preview Compact Mode Name Function (1) Setup Click Setup button to configure settings for cameras, recording, network, scheduler, backup, sensors, relays, alarms and user authentication. (2) Split Screen Mode It provides 4 kinds of split display modes for your selection. User can select the split display modes by clicking the split mode icon.
Page 29 Name Function Use the entire area of the screen to only display the video. To (4) Full screen return, click the arrow icon at bottom of right. Click to switch back to normal display mode. When you switch to full screen in multiple-screen mode, left-click to toggle to only display one of the video in the multiple-screen mode or all.
Page 30 Name Function (8) Alarm Log Viewer Click button to view and search the alarm event logs (see also Chapter 2.17.2).
Page 31: Familiarizing Function In Playback Compact Mode
2.4.2 Familiarizing Function in Playback Compact Mode Name Function (1) Setup Click Setup button to configure settings for cameras, recording, network, scheduler, backup, sensors, relays, alarms and user authentication. (2) Split Screen Mode It provides 4 kinds of split display modes for your selection. User can select the split display modes by clicking the split mode icon.
Page 32 Name Function Use the entire area of the screen to only display the video. To (3) Full screen return, press the right button of the mouse or ESC on the keyboard or click the arrow icon. Click to switch back to normal display mode.
Page 33 Name Function Mark a reference point when reviewing the recorded video file to (5) Bookmark which you may return for later reference (see also Chapter 4. Save the playback file to USB pen drive (see also Chapter 2.11). (6) Backup Click it to view NVR/DVR system’s version and copyright.
Page 34 Name Function (11) To expand the playback time bar from an hour to minute. (Zoom in/Zoom out) Show the progress of the file being played. You may move the (12) Progress bar bar to seek at any location of the track. Using the Zoom In/Out button to expand the playback time from an hour to minute.
Page 35: System Setup
System Setup Click Setup tab in preview/playback mode to switch to system setup mode. In Setup mode, user should see the System Information dialog box is displayed at the first place. In System Information dialog box, it displays the setting options of Language, Date/Time, Network1, Netowrk2 and Storage.
Page 36: General System Setting
2.5.1 General System Setting Setup the language of NVR/DVR system, video type, system date and time, synchronize the system time. Click Setup tab > System Setting; click + to expand list of System Setting and click System Configuration. After changing the settings, click Apply button to save the settings. To un-save the new settings, click Cancel button.
Page 37: System Advanced Setting
synchronize time on a daily basis.  Update Now: User can click Update Now button to adjust time right away. 2.5.2 System Advanced Setting In Advanced of System Configuration, user can setup the daylight saving time, system login setting, and some other system related setting. Click Setup tab >...
Page 38: Daylight Saving Time Setting
2.5.2.1 Daylight Saving Time Setting User can setup daylight saving mode as user is desired. Select the mode of Daylight saving.  Mode 1: Mode 1 is setting up specific start date/time and end date/time.  Mode 2: Mode 2 is setting up fixed day of month in every year for start and end date/time.
Page 39: Customizing System Login Setting
2.5.2.2 Customizing System Login Setting Enable the conditions in Login section you want the system to automatically carry out. Click Apply to save the setting.  Auto Login after system boot up: Login NVR/DVR system automatically when NVR/DVR operating system is started. ...
Page 40: Customizing System Miscellaneous Setting
2.5.3.3 Customizing System Miscellaneous Setting Enable the conditions in Miscellaneous section you want the system to perform. Click Apply to save the setting.  Auto Scan Period: Set the time gap of the Auto Scan function from 3 to 10 seconds. This automatically switches to the next video in cycle depending on the set time gap.
Page 41: Update/Export/Import
2.5.4 Update/Export/Import In Configure Update, user can import the backup configure file to NVR/DVR system and export the configure file to external USB pen drive. Also, user can update the NVR/DVR system’s firmware and IP camera patch file. Click Setup tab > System Setting; click + to expand list of System Setting and click System Configuration >...
Page 42: Import The Nvr/Dvr System Configuration
2.5.4.1 Import the NVR/DVR System Configuration To regain the same settings back from previously backup configuration file. 1. Plug the USB pen drive into the NVR/DVR unit that contains the backup configuration file that user has exported previously. 2. In Configure/Update page, click Import button in Configuration section. 3.
Page 43 4. Then, click Import button. 5. A message dialog box will appear to remind user that the NVR/DVR system will reboot after restoring the backup configuration file. Click OK button to continue. To cancel click Cancel button. 6. After restoring backup configuration file, a message dialog box will appear to inform user that import process is completed.
Page 44: Export The Nvr/Dvr System Configuration
2.5.4.2 Export the NVR/DVR System Configuration Backup a copy of all the settings and allows you to regain the same settings back. 1. Plug in the USB pen drive for saving configuration file. 2. In Configure/Update page, click Export button in Configuration section.
Page 45 3. In Export dialog box, user should see the backup configuration file path and default backup configuration file name. 4. Next, click Export button. 5. A message dialog box will appear to notice user that export process is completed. Click OK button to finish the export process.
Page 46: Upgrade The Nvr/Dvr Firmware
To update the firmware of NVR/DVR system. 1. Plug the USB pen drive that contains the NVR/DVR firmware file. To get the newest NVR/DVR firmware, go to website http://www.aver.com > Support > Download center. 2. In Configure/Update page, click Update button of Firmware.
Page 47 5. A message dialog box will appear to inform user that the upgrade process is completed. Click OK button to restart the NVR/DVR system.
Page 48: Upgrade The Ip Camera Module Patch
2.5.4.4 Upgrade the IP Camera Module Patch To update the firmware of NVR/DVR system. 1. Plug the USB pen drive that contains the IP camera patch file. 2. In Configure/Update page, click Update button of IPCam Module. 3. In upgrade dialog box, the NVR/DVR system will detect the patch file and show the patch file path, patch file name, and version information.
Page 49: Reset To Factory Default
2.5.5 Reset to Factory Default Reset the NVR/DVR system back to factory default value. All configurations will be lost after reset to factory default. Click Factory Default button of Factory default and NVR/DVR system will reboot automatically.
Page 50: Network Setting
Network Setting Select type of IP mode, setup the IP address of NVR/DVR, and configure the DDNS. 1. Click Setup tab > System Setting; click + to expand list of System Setting and click Networking. 2. MAC Address: Displays the MAC address of Ethernet port on LAN card. 3.
Page 51 GATEWAY: A network device act as a passageway to internet. Enter the network gateway IP address DNS: Domain Name Server translates domain names (such as www.abb.com.tw) to IP addresses. Enter the IP address of DNS if it is available.  DHCP: Uses DHCP server assigning NVR/DVR server an IP address.
Page 52: Setup The Nvr/Dvr Server Name
2.6.1 Setup the NVR/DVR Server Name Assign a name for the NVR/DVR system. Alphabet letters and numbers only. Click Setup tab > System Setting; click + to expand list of System Setting and click Networking. User will see the Network Setting dialog box appear. Enter the desire name in Server Name column, then, click Apply button to save the settings.
Page 53: Network Advanced Setting
2.6.2 Network Advanced Setting User can setup camera transmitting, UPnP function, bandwidth limit setting, and network port setting. Click Setup tab > System Setting; click + to expand list of System Setting and click Networking > Advanced tab. Click Setting to configure.
Page 54: Setup The Transmitting Camera
2.6.2.1 Setup the Transmitting Camera Select and click on the camera number in the Transmitting Camera section you want to make it accessible via internet using PCViewer, Remote site control, and iPhone/Andorid Viewer. To select all the cameras, enable the ALL check box. 2.6.2.2 Setup the UPnP Assign a port number for UPnP service.
Page 55: Setup The Network Port
2.6.2.4 Setup the Network Port Assign a Network Port for remote accessing connection.
Page 56: Storage Setting
Storage Setting In storage setting, user can add the storage path, remove the storage path, format hard disk, and set the hard disk recycle time. Click Setup tab > System Setting; click + to expand list of System Setting and click Storage.
Page 57: Formatting The Hard Disk
2.7.1 Formatting the Hard Disk Follow the steps below to format the hard disk for first time installation or re-format the hard disk to the type that can be saved recording video. 1. In Storage Setting page, click Storage tab. 2.
Page 58: Setup Storage Path For Recording Data
2.7.2 Setup Storage Path for Recording Data Without storage path, the NVR/DVR system won’t be able to record. Add a storage path for saving recording video data. In Storage Setting page, click Storage tab. Select hard disk or iSCSI HDD and click button.
Page 59: Setup Hard Disk And Event Log Recycle Time
2.7.3 Setup Hard Disk and Event Log Recycle Time  Delete recorded after Days: If user wants the system to automatically erase the data after a certain days, enable the Delete recorded data after check box and enter the numbers of days in Days text box.
Page 60: Iscsi Setting
2.7.4 iSCSI Setting Connect the iSCSI server on your network to use as a storage path for saving recorded data. Enter the following information to connect the iSCSI server on your network.  Initiate Name: The initiate name of iSCSI server. User can find out on iSCSI server. ...
Page 61 Click Storage tab, user will see the iSCSI HDD is listed in Detected HDD section. To format iSCSI HDD, select it and click Format button. To add iSCSI HDD as a storage path, select it and click button.
Page 62: Camera Setting
Camera Setting To connect and configure the analog and IP camera. Click Setup tab > Camera Setting.
Page 63: Connect The Analog Camera
2.8.1 Connect the Analog Camera Analog camera only supports on E1008H model. 1. Connect the DVI cable to the video in port of NVR/DVR. 2. Connect the analog camera to the DVI cable of NVR/DVR and power on the analog camera.
Page 64: Connect The Ip Camera
Available (MP) column. - Search List: To perform the auto search IP camera on your LAN network and list search result. Also, the NVR/DVR system provides Active IP function for user to configure AVer IP cameras series from NVR/DVR site (see also Chapter 2.8.2.1).
Page 65 3. Select the Type of camera as IP in Camera List. 4. Then, click Search button to find IP cameras on LAN network. 5. In Search result list, select the IP camera that user wants to connect. Then, select the IP camera channel that user wants to connect the selected IP camera.
Page 66  IP Address: Enter the IP camera’s IP address.  Port: Enter the port of connecting IP camera.  Protocol: Enter the brand name of the IP camera. For example: AVer, AXIS...etc.  Model: Enter the model type of the IP camera. For example: FX3000 ...
Page 67: Active Ip Function
2.8.2.1 Active IP Function The Active IP function allows user to configure the AVer IP camera series’ IP mode, IP address, subnet mask, gateway, port, login ID, and password on NVR/DVR system. The Active IP function supports AVer IP camera series only.
Page 68 In Active IP dialog box, user can change IP mode of the IP camera and configure related parameters. After configuring, click OK to save the setting.
Page 69: Camera Detail Configuration
2.8.3 Camera Detail Configuration User can configure the IP/analog camera’s detail settings. Click Setup tab > Camera Setting; click + to expand list of Camera Setting and click the Camera number that user wants to configure. Or, click Setting button of IP camera in Camera Management dialog box.
Page 70: Basic
 Basic  Video Adjustment: Configure the Brightness, Contract, Hue, Saturation, and Sharpness of IP camera.  IP Camera: Enable/disable Speaker and MIC of IP camera.  Audio: Enable/disable audio function of IP camera.
Page 71: Preference
 Preference In Preference page, user can tune the IP camera white balance, select display color or black & white, set the flicker frequency, change the video orientation, and adjust the some advance settings. After completing the setting, click Apply to save the setting and Cancel to keep the old setting.
Page 72  Denoise: Select Disable/2D/3D/Auto to reduce the excessive noise on the video image. Select Auto and set the Sensitivity level.  AE Profile (Auto Exposure Profile): Select the auto exposure scenes – Indoor, Outdoor, or ManualIRIS.  IR-cut Filter: The IR cut filter is a mechanism that prevents the infrared light from hitting the sensor.
Page 73: Exposure
 Exposure In Exposure page, user can set the exposure area, exposure mode, and calibrate the DC Iris. After completing the setting, click Apply to save the setting and Cancel to keep the old setting. The Exposure setting only support for IP camera. ...
Page 74: Stream
 Stream User can setup Codec, Resolution, FPS, Bitrate Mode, and Quality of Stream 1, and Stream 2 on the IP camera channel. The Stream 1 is enabled in default. After completing the setting, click Apply to save the setting and Cancel to keep the old setting. The NVR/DVR system doesn’t support on stream 2 setting.
Page 75: Roi
 ROI stands for Region on Interest. It helps users to optimize bandwidth and storage. Users can select the key area to transmit as separate streams for targeted preview and recording. The ROI setting only support for IP camera. 1. Select the Sensor Mode and Stream. 2.
Page 76: Smart Stream
 Smart Stream Smart Stream optimizes bandwidth and storage space by increasing or decreasing quality for selected areas based upon criticality. Users can define up to 5 areas per stream to ensure sharp images for crucial areas, while saving bandwidth on non-essential areas. Typical applications include entrances, access gates, production lines, art galleries and museums.
Page 77: Privacy Mask
 Privacy Mask In Privacy Mask page, user can enable 3 privacy masks. Simply adjust the size and position the mask on the area user wants to conceal. The viewer will not be able to see the masked area. It will cover the video screen with black frame.
Page 78: Motion Detection
 Motion Detection In the motion detection page, the frame will blink when the motion detected has reached the percentage threshold setting. This feature can be utilized to trigger a response in Event setting. 1. Enable the region check box (Region 1, Region 2, Region 3) to create a motion detection frame.
Page 79: Iva
 Form drop-down list select the IVA function – Cross detection, Tampering, Missing object, or Suspicious object.
Page 80 Cross Detection Cross detection function detects moving objects that cross the virtual lines that user has set up in IP camera application and to trigger the alarm. Enable Cross line 1/2 check box You will see the red/green line is shown on the video screen. Drag the red line or green line to set the area for cross detection.
Page 81 Tampering Select Enable tamper detection to enable tampering function. And, alarm will trigger when the following situation has occurred.  Spray-painting: Alarm is triggered when the camera has detected the painting sprayed on the camera’s view for over 2 seconds. ...
Page 82 Missing Object Select a certain object on the screen for the camera system to detect; System gives alarm when the object disappears. 1. Select the Missing Object from the drop-down list. 2. A red frame will show up on the screen. Click and drag the red frame to the object position and click the frame to adjust the size of frame.
Page 83 Suspicious Object Suspicious Object is an unusual object appears on the screen. 1. Select the Suspicious Object from the drop-down list. 2. A red frame and green frame will show up on the screen. The red frame is defined as detecting zone and green frame is defined as object size frame.
Page 84: Sensor
 Sensor The Sensor setting only support for IP camera. Setup the sensor of IP camera. 1. In Camera Management dialog box, click Sensor tab. 2. Click the drop-down list and select the sensor ID number. 3. Enter sensor name in Name column 4.
Page 85: Relay
 Relay The Relay setting only support for IP camera. Setup the relay of IP camera. a. In Camera Management dialog box, click Relay tab. b. Click the drop-down list and select the relay ID number. c. Enter relay name in Name column d.
Page 86: Mfz
 The IP camera has motorized lens can perform MFZ function(motorized focus and zoom). MFZ function doesn’t suport for analog camera. Adjusting the focus or zoom in/out of IP camera. Name Function Auto focus Automatically focus on where focus cursor ( ) has pointed.
Page 87 Name Function Press to zoom out continuous. Continuous zoom out To reset the zoom back to the center of screen view in Reset default value (1x).
Page 88: Setup Ptz Function
 Setup PTZ function Setup IP Camera PTZ Function User can enable PTZ function if the IP camera has supported. 1. In Camera Management dialog box , click Setup tab 2. Then, select Camera # > PTZ tab. 3. In PTZ setup page, mark Use PTZ to enable PTZ function. 4.
Page 89 (the setup time period is 1~60 seconds). After is done, click Save to keep the settings. Setup Analog Camera PTZ Function User can enable PTZ function if the Analog camera has supported. 1. In Camera Management dialog box , click Setup tab 2.
Page 90 5. Preset Setting: use the control panel to adjust the position of the camera and select the Preset Number to assign a number for the camera preset position. After is done, click Save to keep the settings. Use these 2 buttons to Zoom in/Zoom out Use the direction the lens.
Page 91: Familiarizing Functions On Ptz Control Panel
2.8.4 Familiarizing Functions on PTZ Control Panel User can control PTZ camera through PTZ control panel in preview mode. Enable and set up the PTZ camera; refer to Setting PTZ Function. 1. In preview mode, click (PTZ) icon to call out PTZ control Panel.
Page 92 2. The functions’ description of PTZ control panel is as following. Name Function (1) Camera preset Move the PTZ camera to the preset point. position number (2) Group AutoPan Select to automatically operate PTZ camera in group. (3) Direction buttons’ Adjust the moving speed of the PTZ camera lens.
Page 93: Record Management
Record Management The recording schedule is always record in default. If the storage path is not set, the NVR/DVR system couldn’t record. Click Setup tab. Then, select Record Management. Mark Enalbe Optimized Recording to enable dual stream recording. Select the day for Days to keep high-quality recorded data to recycle the high quality record data.
Page 94 Event Recording Start recording the video from the selected camera only when the system detects movement. Once a motion is detected, the system automatically saves the previous frames and stop based on the Pre-Buffer time (0~10 seconds) and Post-buffer Time (0~999 seconds) settings. Click Detail button to view event recording items. Now, only support motion recording on Event recording mode.
Page 95 After selecting the recording mode, select date and time on date time table. To select or un-select all blocks, click the area in red circle. If user wants to apply this record schedule to other or all camera channels, use Apply to function to apply to other camera channel.
Page 96: Alarm Schedule
2.10 Alarm Schedule Setting up the schedule for alarm action that user has setup in Alarm setting (see also Chapter 2.12). According to the alarm schedule, the alarm actions will be active and alarm will be issued when action has matched the conditions. 1.
Page 97 3. Next, click Apply to save the setting. 4. To disable the alarm schedule, select “Disable” and click on the date and time table and click Apply to save the changes.
Page 98: Backup Setting
2.11 Backup Setting Backup the recorded files to external USB pen drive. In Backup setting, user can select different channels or time period to backup at the same time. The backup files can be playback on PC by Qplayer application that is included when backup. Playing backup file on PC refer to Chapter 1.
Page 99 5. User can backup multiple recorded file (different channels and different time period) at the same time. Repeat the above steps to create the backup file and click Add button. The different backup files are distinguished by Folder Name that user has given. The multiple backup files limit is 3 files at the same time.
Page 100: Alarm Setting
2.12 Alarm Setting To setup an alarm setting, user needs to complete following steps: Setting up the alarm conditions (see also Chapter 2.12.1). Setting up the alarm actions (see also Chapter 2.12.2). Setting up the alarm schedule (see also Chapter 2.10).
Page 101 4. In No. column displays the alarm setting number. The number of alarm is assigned by NVR/DVR system in default. 5. Enter alarm name and description for this alarm setting in Name and Description column. 6. Next, select “Trigger if any” to activate alarm if system falls to one of the conditions or “Trigger if all”...
Page 102 7. In Camera section, select and click on the camera number in Motion and Video Loss to set the condition for the system to alarm. Motion: select and click on the camera number (01 to 08) to set the condition for the system to alarm.
Page 103 8. In Sensor section, select and click on the sensor number to set the condition for the system to alarm. If the sensor normal status is high, set the sensor condition to low. IP Camera Sensor: To adjust sensor high/low that is connected on the IP camera. Continue trigger duration: Set a time period that when sensor has been trigger and stay in the same status for that period, then the alarm will be sent out.
Page 104 9. In System section, mark the check box to set the conditions that are caused by system. Reboot: when the NVR/DVR system reboot without abnormal condition, the system will send out the alarm message. Abnormal Reboot: when the NVR/DVR system reboot in irregular condition, the system will send out the alarm message.
Page 105 12. To modify the alarm condition setting, click Setting button of Alarm # that user has created. Remember to click Apply to save the changes after modification. 13. To delete the alarm #, select the alarm # that user wants to delete and click Delete button.
Page 106: 2.12.2 Setup The Alarm Action
2.12.2 Setup the Alarm Action Setup the alarm action for system to perform when the alarm condition has been triggered. 1. Click Setup tab > Alarm Setting. 2. Then, click Setting button of Alarm # that user has created in Alarm Information dialog box. Also, user can select the Alarm# from the list under Alarm Setting.
Page 107 4. The No., Name, Description, and Priority column display the current alarm’s information. The Trigger Type displays the current alarm’s trigger condition. 5. In Alarm Reset section, click the camera number to set the reset condition of alarm. Once alarm is reset, all alarm action will stop at the moment. If the sensor normal status is high, set the alarm reset condition to low.
Page 108 6. In Action section, user may now set the alarm action for the system to perform when the alarm condition is activated. Launch E-Map: Display mini E-map on the screen. Enlarge Camera View Switch to only display video in Preview mode from where the alarm is activated. a.
Page 109 IP Camera Relay Set to enable/disable the relay operation when the alarm is activated. Play Warning Sound Play alarm sound. Send E-mail Send an electronic text message. Beside the Send Email check box, click Detail. In the E-mail Setting dialog box, click OK to exit and save the setting and Cancel to exit without saving the setting.
Page 110  Mail Fill the mailing information. Click Test Account button can exam the mail is workable or not.  From: Enter the sender e-mail address.  To and CC: Enter the recipient email address and separate it with comma or a semicolon (;).
Page 111 Get a Google account. Go to Google website and follow the instruction to get a Google user account. Copy the below URL to your Google browser. http://www.aver.com/Youtube Using your Google account to login and click “Allow” to enable Google WAN storage function.
Page 112 Get a Dropbox account. Go to Dropbox website and follow the instruction to get a Dropbox user account. Copy the below URL to your browser. http://www.aver.com/Dropbox Using your Dropbox account to login and click “Allow” to enable Dropbox WAN storage function.
Page 113 PTZ preset point Position the PTZ camera based on the preset point setting. Beside the PTZ preset point check box, click Detail. In the Trigger PTZ Preset Setting dialog box, select the PTZ camera number then select the Enable check box. Select the position of the PTZ camera when the alarm is activated and ended.
Page 114: User Account Setting
2.13 User Account Setting Only administrator level authority can access User Setting. The maximum user accounts are 2.13.1 Create the User Account 1. Click Setup tab. 2. Then, click User Setting and the User Information dialog box is displayed. The Admin is default user and cannot be deleted. 3.
Page 115 4. In User Setting dialog, Select and fill in the following information.  Name: Enter the user name.  Description: Enter the user description.  Password: Enter the user password.  Confirm Password: Enter the same user password for confirmation. ...
Page 116 5. Click Apply to save the account setting. The user account is list in User Setting list. Adding another user account, repeat above steps. Modifying the user account; click Setting of user account in User Information dialog.
Page 117: Delete The User Account
2.13.2 Delete the User Account User can remove un-wanted or expired user account. 1. Click Setup tab in Preview mode. 2. Then, click User Setting in Advanced NVR/DVR Setting section and the User Information dialog is displayed. 3. Mark the user account in User Information dialog; then, click Delete button.
Page 118: I/O Setting
2.14 I/O Setting Setup I/O device status. 2.14.1 Sensor Setting 1. Click Setup tab > Alarm Setting > Sensor tab. 2. Click the drop-down list and select the Sensor #. 3. Enter sensor name in Name column. 4. The system automatically detects the card and input number. In the Content section, user can enter a short description of sensor in Description column.
Page 119: Relay Setting
2.14.2 Relay Setting 1. Click Setup tab > Alarm Setting > Relay tab. 2. Click the drop-down list and select the Relay #. 3. Enter relay name in Name column. 4. The system automatically detects the card and input number. In the Content section, user can enter a short description of relay in Description column.
Page 120: Emap Setting
2.15 Emap Setting E-Map can hold up to 8 maps in *.jpg or *.bmp format. User may locate the camera, sensor and relay on the map. 2.15.1 Setup the Emap Click Emap Management. The Emap dialog box will appear on screen.
Page 121 Click Edit button to switch to Emap setup mode. Then, click the Map number (1 to 8) that user want to setup. Next, click icon to setup name of Emap and load a map figure. When the Emap Setting dialog box appears, click the open file icon ( ) to locate and select the map Enter a name for this Emap in Name column.
Page 122 When the inserted map appears on the Emap screen, user may now drag the camera, sensor, and relay icons to its place on the map. Icons on the map can be relocated anywhere. If user is going to locate the icon on the map to other area, right-click on the icon on the Emap and click remove to put the icon back to the Resource list.
Page 123: Ipos Setting
2.16 iPOS Setting Set from which camera screen to display the data from the POS equipment. Click Setting, to set the POS Console Setting. [Note] Please using USB to RS232 converter (ex: MOXA) to connect with your POS device. 1. Click Setup tab. Click + to expand the System Setting list and select Hardware Device. 2.
Page 124  Text Filter: Enter the word you want to be removed. 5. To setup another iPOS setting, repeat the above steps. 6. To modify the iPOS setting, click the Setting button of iPOS.
Page 125 7. To delete the iPOS, mark the iPOS and click Delete button. 8. To view the iPOS event log, refer to Chapter 2.17.3.
Page 126: Log Viewer
2.17 Log Viewer Show the record of activities (alarm, event, iPOS) that take place in the system. User can view and search for specific log. 2.17.1 Using the Event Log Viewer Click Event Log icon ( ) in preview mode. The Event Log Viewer dialog box is appeared and located at bottom of left side screen.
Page 127 To filter the logs, select and click the select Type -- System, Network, Operation, Event, or All. Set the Start Date/Time and End Date/Time period to search the logs. User also can search specific logs by specific Keyword. Click Search button to start searching. The search results are displayed in the below column.
Page 128 Click on the event log can view the log video. Click Export button can output the log result list to external USB pen drive in *.cvs file format.
Page 129: Using The Alarm Log Viewer
2.17.2 Using the Alarm Log Viewer The alarm log viewer is both supported in preview and playback mode. View the Alarm Event Alert and display warning information. Click Alarm Log icon ( The Alarm Log Viewer dialog box is appeared and located at bottom of left side screen. User can click icon to expand the Alarm Log Viewer dialog box on the screen.
Page 130 Clicking Refresh button to refresh the alarm events list. Double-click on alarm event can playback the event video.
Page 131: Search Alarm Event Logs
Search Alarm Event Logs Searching the specific alarm event. Click Alarm Log icon ( The Alarm Log Viewer dialog box is appeared and located at bottom of left side screen. User can click icon to expand the Alarm Log Viewer dialog box on the screen. Then, click Search tab in Alarm Log Viewer dialog box.
Page 132 In Alarm Log Viewer dialog box, select the Camera that user wants to search. Multiple cameras selection is allowed. Set the searching period at Start Date/Time and End Date/Time column. Searching by specific keyword, enter the keyword in Keyword column. Click Search button to start searching.
Page 133: Using The Pos Log Viewer
2.17.3 Using the POS Log Viewer Search the iPOS event. The POS Log viewer is both supported in preview and playback mode. 1. Click POS Log ( 2. The POS Viewer dialog box is appeared and located at bottom of left side screen. User can click icon to expand the POS Log Viewer dialog box on the screen.
Page 134 3. In POSViewer dialog box, select the Camera that user wants to search. 4. Set the searching period at Start Date/Time and End Date/Time column. 5. Searching by specific keyword, enter the keyword in Keyword column. Mark Match whole words exactly option to 100% match the keyword that user has entered. 6.
Page 135: Nvr/Dvr System Tools
2.18 NVR/DVR System Tools 2.18.1 Hard Disk Calculator Estimate the hard disk recording capacity. The result of calculation is a rough value which only for reference. The hard disk record capacity will be varied by the real record quality and complexity of video scene.
Page 136: On Screen Keyboard
In Hard Disk Calculator dialog box, enter the expect hard disk size or expect recording time in Expected HD Size (GB) or Estimated Recording Time (Days), and then click Calculate button. The Total Recording Time (Days) column is shown the current hard disk recording capacity.
Page 137: Chapter 3 Monitoring The Nvr/Dvr
Chapter 3 Monitoring the NVR/DVR After setting up the NVR/DVR system, user can start to monitor the NVR/DVR in preview mode. The following chapters are going to describe the monitoring functions in preview mode.
Page 138: Manage Camera Channels
Manage Camera Channels User can arrange the channel display position as user is desired. Select the camera in Camera section. Then, drag the camera to the channel that user wants to be displayed. Next, User should see the live video on the channel screen. The channels can be switched between each channel;...
Page 139: Meaning Of Icons And Figures
Meaning of Icons and Figures  The description of icons on each channel: The first icon is indicated the current recording status. - Red color( ): recording - Gray color( ): no recording The icon is indicated the motion record status. - Red color( ): motion recording - Gray color(...
Page 140: Enable/Disable The Camera Channel
Enable/Disable the Camera Channel In Camera list, user can enable/disable camera. When camera is disabled, monitor and record function are both disable. Right-click on the camera in Camera list, select disable or enable the camera.
Page 141: Screen Channel Display Mode
Screen Channel Display Mode The NVR/DVR has provided 6 types of screen display mode – single ( ), QUAD ( 9-split screen ( ), and 8-split screen ( ). To select the screen display mode, click on the screen display icon.
Page 142: Enable/Disable The Sound Of The Channel
Enable/Disable the Sound of the Channel User can click the audio icon ( ) to mute ( ) the sound of channel. Click the audio icon ( again to turn on the sound. Muting the sound Turn on the sound...
Page 143: Switch Multiple Screen To Single Screen Display
Switch Multiple Screen to Single Screen Display In multiple screen display mode, user can double-click on the channel screen to switch to single display screen mode. Double-clicking again on channel screen, the screen display will switch back to multiple screen display mode. Double-clicking on channel screen can switch to single screen display mode...
Page 144: View The Emap
View the Emap Click Emap( ) to call out the Emap dialog box. Click icon on E-map dialog box to expand the E-map dialog box on the preview screen. When alarm occurred, the icons on the map will turn to flash status. Click Map #(ex: Map 2) can switch to the selected map.
Page 145: Snapshot The Screen
Snapshot the Screen Taking a quick capture of current display screen and save in *.jpg format to external USB pen drive. 1. Plug in the USB pen drive to USB port of NVR/DVR unit. 2. In preview mode, Click the snapshot icon ( ) and the snapshot dialog box is appeared.
Page 146: Full Screen Display
Full Screen Display View the surveillance screen in full screen display mode. In preview mode, click full screen icon ( ) to switch to full screen display. Click the full screen icon ( ) on the bottom of right corner to return back to normal display mode. Click it to return back to normal display mode...
Page 147: Hide The Camera List
3.10 Hide the Camera List User can hide the camera list to have larger view of surveillance screen. In preview mode, click icon and the camera list will be hided. To show the camera list again, click icon.
Page 148: Auto Display Channel In Cycle
3.11 Auto Display Channel in Cycle Click to start channel display in cycle automatically. To stop auto cycle display, click again. If total channels are 8 channels in 8-split screen display mode, the auto display cycle function won’t work.
Page 149: Enable/Disable 2-Way Audio Function
3.12 Enable/Disable 2-Way Audio Function This function allows the NVR/DVR server site and IP camera site to talk via internet using microphone. Make sure your microphone and speakers work before using this function. Click icon to enable 2-way audio function. To disable, click icon again.
Page 150: Chapter 4 Playback Recorded Video On Nvr/Dvr System
Chapter 4 Playback Recorded Video on NVR/DVR System In this chapter, it is going to description how to playback recorded video on NVR/DVR system in several ways and introduce some functions that user can operates in playback mode. Playback on NVR/DVR System User can playback the recorded video on NVR/DVR system instantly.
Page 151: Playback The Specific Date/Time Period
Playback the Specific Date/Time Period User can select the specific date and time period to playback. 1. In playback mode, click Calendar ( ) icon. 2. In Calendar dialog box, select the date (date, month, year) that user wants to playback. The date in bold text indicates it has recorded data.
Page 152: Using The Event Search To Playback The Event
Using the Event Search to Playback the Event In playback mode, user can use Event Search to find the specific event to playback. 1. Select the channel that user wants to search. 2. Click (Search) icon >> (Event Search) Then, the Event Search dialog box would appear at side area.
Page 153 5. When the Event list appears, click and select the item user wants to view; but not all the events can be playback such as Sensor. 6. To close the Event Search dialog, click icon.
Page 154: Using The Visual Search To Playback The Specific Time
Using the Visual Search to Playback the Specific Time In playback mode, user can use Visual Search to find the specific time to playback. 1. Click (Search) icon, then select (Visual Search) icon. The Visual Search dialog box would appear under the area. 2.
Page 155 5. When a series of frames appear by date, click on the frame to display another series of frames and search by every 2 hours of that date, every 8Minutes of that hour, and every 30seconds of that minute. Using to go to hour, minute, and second page.
Page 156: To Bookmark A Section Of The Video
To Bookmark a Section of the Video User can bookmark a specific time of video section. 1. Using the mouse to move the playback time progress bar to the time that user wants to bookmark. 2. Then, click icon. The Bookmark dialog box is appeared on the screen. 3.
Page 157 Select and click one in the bookmark list to review the file. To modify the bookmark, select the bookmark and click Edit button. To delete the bookmark, select the bookmark and click Delete button. To close the Bookmark dialog box, click icon.
Page 158: Use The Playback Mode
Use the Playback Mode 4.6.1 Manage Channel Display Position User can arrange the channel display position that user is desired. Select the camera in camera list section. Then, drag the camera to the channel that user wants to playback. Next, User should see the video playback on the channel screen. The channels can be switched between each channel;...
Page 159: Enable/Disable Sound Of The Channel
4.6.2 Enable/Disable Sound of the Channel First, switch to single screen display mode. Then, Click the icon on the channel screen to disable the sound play. Click again to enable sound play.
Page 160: Switch Multiple Screen Display To Single Screen Display
4.6.3 Switch Multiple Screen Display to Single Screen Display In multiple screen playback mode, user can double-click on the channel screen to switch to single display screen mode. Double-click on channel screen again; the screen display will switch back to multiple screen playback mode. Double-click on the channel can switch to single screen display...
Page 161: Full Screen Display
4.6.4 Full Screen Display View the playback screen in full screen display mode. In playback mode, click full screen icon ( ) to switch to full screen display. Click full screen icon ( ) on the bottom of right corner to return back to normal display mode...
Page 162: Hide The Camera List
4.6.5 Hide the Camera List User can hide the camera list to have larger view of surveillance screen. In playback mode, click icon next to preview tab and the camera list will be hided. To show the camera list again, click icon.
Page 163: Output A Video Clip To A Usb Pen Drive
4.6.6 Output a Video Clip to a USB Pen Drive 1. Switch the playback screen to 1 single screen display mode. 2. Using button to expand the time bar for easy to set the segment period. 3. Click (Segment) button to set the mark. 4.
Page 164  Start Date/Time: Displays the begin time and date of segment video file.  End Date/Time: Displays the end time and date of segment video file.  Video Format: Select the video format -- *.DVR or *.mp4 that user wants to save. ...
Page 165: Snapshot The Screen View
4.6.7 Snapshot the Screen View 1. Select the channel or all channels. 2. Plug the USB pen drive to NVR/DVR unit. 3. Click Snapshot ( ) button. 4. In Snapshot dialog box, check the Save path has been detected by NVR/DVR system. If the save path doesn’t found, click Rescan Device button to re-detect it.
Page 166: Chapter 5 Playback By Qplayer
Chapter 5 Playback by Qplayer You can playback the backup files by using QPlayer applications on the PC. When you back up the recorded file, QPlayer applications are automatically included in the backup folder if user has enabled the selection of Inculde player when backup when backup recorded file. With QPlayer, it is similar in Playback mode and supports different split screen types to view all the video at the same time.
Page 167: Chapter 5.1 Familiarizing Functions Of Qplayer
Chapter 5.1 Familiarizing Functions of Qplayer In Qplayer main UI, click File > Open File to located the backup file folder. Please copy the whole backup folder under hard disk direction of PC (ex: C:\). The functions of Qplayer will be described in following: (5) (6) (7) (8) (10)
Page 168 Name Function (2) Split Screen Mode Select from 7 kinds of split screen type to playback the recorded video file of all the camera, or one camera over the other or alongside on a single screen. To only display one of the video in the multiple-screen mode, double click on the video screen you only want to display.
Page 169 Name Function (10) Power button Call up the Power dialog box. In the Power dialog box, user may do the following: Exit: To shutdown the NVR/DVR system. Cancel: To exit Logout dialog box. If the keyboard is not available, you may use the Virtual (11) On Screen Keyboard.
Page 170 Name Function Show the progress of the file being played. You may move the (16) Progress bar bar to seek at any location of the track. Using the Zoom In/Out button to expand the playback time from an hour to minute. Meaning of color in progress bar: - Red: Alarm record - Green: Motion record...
Page 171: To Bookmark A Section Of The Video For Playback
5.1.1 To Bookmark a Section of the Video for Playback User can bookmark a specific time of video section. Using the mouse to move the playback time progress bar to the time that user wants to bookmark. Then, click icon. The Bookmark dialog box is appeared on the screen. Click Add button to create the new reference mark in the bookmark list.
Page 172 Select and click one in the bookmark list to review the file. To modify the bookmark, select the bookmark and click Edit button. To delete the bookmark, mark the bookmark and click Delete button. To close the Bookmark dialog box, click icon.
Page 173: Chapter 6 Using The Pcviewer
Chapter 6 Using the PCViewer User can use Microsoft Internet Explorer to access NVR/DVR system by entering the IP address. To use this feature, make sure that your PC and NVR/DVR server both are connected to the internet and the Network feature is enabled. Accessing this feature for the first time you need to install plugin component, allow or click to install and you should be able to connect and login afterwards.
Page 174: Familiarizing Functions Of Preview Mode
Familiarizing Functions of Preview Mode (5) (6) (7) Name Function (1) Playback Click it to switch to playback mode and playback recorded video form remote NVR/DVR server(see also Chapter 6.2). (2) Preview Click it to switch to preview mode. Lists all cameras. Click the camera # to view in single screen (3) Camera list display mode or click camera group to view in multi-screen display mode.
Page 175: Familiarizing Functions Of Playback Mode
Familiarizing Functions of Playback Mode (12) (13) (10) (11) Name Function (1) Playback Click it to switch to playback mode (2) Preview Click it to switch to preview mode (see also Chapter 6.1). (3) Camera list Lists all cameras. Click the camera # to view in single screen display mode or click camera group to view in multi-screen display mode.
Page 176 Name Function (7) Result display area Display the search result of found recorded data. (8) Date and Time It shows the current date and time. Display the recorded date, time and play speed. (9) Status bar From left to right order: (10) Playback Control Buttons Previous: Click it to go to previous time period.
Page 177: Appendix Recovery Nvr/Dvr System Through The Usb Port
Save the firmware on USB pen drive and through the USB port on NVR/DVR unit to recovery the firmware of NVR/DVR system. All the configuration will be erased after recovery process. 1. Download the firmware from website http://surveillance.aver.com/ >> Support >> download Center. Then, click Search button to search firmware.
Page 178 7. After all procedures have completed, the Reboot window is show up. Remove the USB pen drive from NVR/DVR unit and click Reboot button to restart NVR/DVR system.
Page 179: Warranty Notice
WARRANTY NOTICE LIMITED WARRANTY AVer Information, Inc. warrants this product to be free of defects resulting from faulty manufacture or components under the following terms: WARRANTY LENGTH Labor is warranted for (3) three year from the date of purchase. Parts are warranted for (2) two year from the date of purchase.
Page 180 This warranty gives you specific legal rights, and you may also have other rights granted under state law. These rights vary from state to state CONTACT INFORMATION Taiwan & International No. 157, DA-An Rd., Tucheng Dist., New Taipei City, Taiwan TEL: 886-2-2269-8535 Web Site: http://www.aver.com/...

AVer E1000 Series User Manual

Quick Links

Related Manuals for AVer E1000 Series

Summary of Contents for AVer E1000 Series

Table of Contents