Page 1
EH6000H series EH6108H /EH6216H Quick User Guide...
Page 3
No part of this document may be reproduced or transmitted in any form, or by any means without the prior written permission of AVer Information Inc. AVer Information Inc. reserves the rights to modify its models, including their characteristics, specifications, accessories and any other information stated herein without notice.
EH6108H If there is any damage, shortage or inappropriate item in the package contents, please contact with local dealer EH6108H+ has 2 models; one is come with DVD-ROM and another one is come with HDD tray. (1) EH6108H DVR unit...
Page 6
EH6216H If there is any damage, shortage or inappropriate item in the package contents, please contact with local dealer EH6216H has 2 models; one is come with DVD-ROM and another one is come with HDD tray. (1) EH6216H DVR unit (7) Power Cord (* The power cord may vary according (2) Optical USB mouse...
QUICK USER GUIDE Hardware Installation A. Install the hard disk For hard disk spec, please referring to http://surveillance.aver.com/download-center → Embedded Hybrid DVR/NVR → EH6000H series → Hardware Recommendations Follow the illustrated instructions below to install the hard disk: 1. Loosen all screws(2 side and back) and push 2.
Page 8
5. Turn the plate and hard disk over carefully and 6. Plug the SATA cable into SATA connector on screw the hard disk on the plate. If hard disk the PC board. cannot match to the screw hole, then, you may [Note] adjust the hard disk position to match the 1.
Page 9
QUICK USER GUIDE Screw the holder on the DVR unit. Push the cover forward and secure the cover You may now connect all the cables and power on the DVR unit.
Page 10
All connected devices have their own power supply are necessary. EH6108H The back panel of the DVR unit, user can connect up to 8 cameras in combination of analog and IP camera. The DVR unit also can connect 16 sensor devices, 4 alarm devices, and output video to a TV or CRT/LCD monitor.
Page 11
QUICK USER GUIDE EH6216H The back panel of the DVR unit, user can connect up to 16 cameras in combination of analog and IP camera. The DVR unit also can connect 16 sensor devices, 4 alarm devices, and output video to a CRT/LCD monitor.
2. Using Remote Controller(Optional accessory) After DVR unit has been setup, user can use remote control to preview, playback, backup, reset alarm, output video and so on functions. 3. Using Front Panel buttons(EH6108H and EH6216H only) It’s an optional way to operate DVR unit. Front panel button function acts as same as remote controller.
Page 13
QUICK USER GUIDE 4. The hard disk must be formatted before user can use it with DVR unit. Following the below steps to format the hard disk. Before formatting hard disk, please stop all operations on DVR system. While formatting hard disk, the CPU usage will be near to 100% and might slow down the DVR system response.
IV. Familiarizing the Buttons in Preview Mode Name Function (1) Exit Reboot: To restart the DVR system. It is required to enter the password Power Off: To shut down the DVR system. It is required to enter the password Login: Using different ID to login to DVR system. Cancel: To return to DVR application.
Page 15
QUICK USER GUIDE Name Function (12) Snapshot Capture and save the screen shot in *.jpg format. (13) Event log Show the record of activities that take place in the system. (14) AutoScan Start/Stop video screen cycle switch. (15) Full screen View in full screen.
Familiarizing the Buttons in Playback Mode Click Playback button at the lower right corner of Preview UI to switch to Playback mode. Name Function Select from 6 different split screen type to playback the recorded video file of (1) Split Screen all the camera, or one camera over the other or alongside on a single Mode screen.
Page 17
QUICK USER GUIDE Name Function Next: Go to the next frame. (4) Playback End: Go to the end of the recorded video file. Control Buttons Select the date on the calendar and the time from 00 to 23 to where to start (5) Date playing the recorded video file.
Page 18
Name Function Mark a reference point when reviewing the recorded video file to which you (14) Bookmark may return for later reference. 1. Click Bookmark button 2. In the Bookmark dialog box, you may do the following: Add to create the new reference mark in the bookmark list. Edit to change the mark description.
Page 19
QUICK USER GUIDE Name Function Search for the next event or changes in the motion detector frame. You can (16) Find Next use this when you are using Event Search function. Search from the recorded activities that were recorded in event log (i.e., (17) Event Search Sensor, Motion, Video Loss).