Table of Contents
Advertisement
Quick Links
ZB-2510 Series User Manual
Warranty
All products manufactured by ICP DAS are warranted against defective
materials for a period of one year from the date of delivery to the original
purchaser.
Warning
ICP DAS assumes no liability for damages consequent to the use of this
product. ICP DAS reserves the right to change this manual at any time
without notice. The information furnished by ICP DAS is believed to be
accurate and reliable. However, no responsibility is assumed by ICP DAS
for its use, or for any infringements of patents or other rights of third
parties resulting from its use.
Copyright
Copyright 2009 by ICP DAS. All rights are reserved.
Trademark
The names used for identification only may be registered trademarks of
their respective companies.
ZB-2510 Series User Manual, Ver. 1.2
Page 1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ICP DAS USA ZB-2510
Summary of Contents for ICP DAS USA ZB-2510
- Page 1 Copyright Copyright 2009 by ICP DAS. All rights are reserved. Trademark The names used for identification only may be registered trademarks of their respective companies. ZB-2510 Series User Manual, Ver. 1.2 Page 1...
-
Page 2: Table Of Contents
Quick Start for the ZB-2510 Series ..............14 5.1 Installing the ZB-2000 Driver ..............14 5.2 Installing the Hardware and Driver ............16 5.3 Installing the Configuration Tool............20 5.4 Quick Configuration for the ZB-2510 Series ........22 Appendix ..........................24 Ordering Information ....................27 Accessories ........................ -
Page 3: Introduction
PA-version is the transmission range. The ZB-2510-T supports an extended transmission range of up to 100 meters, whereas the ZB-2510-PA can transmit to a maximum of 700 meters. Both modules are able to operate in broadcast and user-defined route modes. When the repeater is set to broadcast mode, the transmission route is constructed by the ZigBee Host. -
Page 4: Specifications
• ISM 2.4 GHz Operating Frequency. • Full Compliance with 2.4 G IEEE802.15.4/ZigBee Specifications. • Wireless transmission range up to 100 m (LOS) (ZB-2510/ZB-2510-T) • Wireless transmission range typical for 700 meters, up to 1 km (LOS)(P/PA) • USB Interface for configuration. -
Page 5: Product Description
3. Product Description 3.1 Internal I/O Structure ZB-2510 Series User Manual, Ver. 1.2 Page 5... -
Page 6: Appearance
3.2 Appearance ZB-2510 Series User Manual, Ver. 1.2 Page 6... -
Page 7: Dimensions (Units: Mm)
3.3 Dimensions (Units: mm) ZB-2510 Series User Manual, Ver. 1.2 Page 7... -
Page 8: Operating Modes And Applications
If a problem occurs on the current routing User-defined Route path, data will be automatically switched to another routing path. Two routing paths can Mode be configured. (Back-up Route) Refer to User-defined Route Mode with a back-p Route ZB-2510 Series User Manual, Ver. 1.2 Page 8... -
Page 9: Zigbee Repeater Usage
ZigBee (*3) Device data Repeater ID Repeater forwarding data (*b) received from the ZigBee (*a) device Repeater configuration table 1 ZB-2510 Series User Manual, Ver. 1.2 Page 9... -
Page 10: User-Defined Route Mode With A Back-Up Route
Sometimes, if the weather causes a device to be inoperable, or the engineer is a long distance from the location, the recovery time will be increased. Thus, the network self-recovery and redundancy functions are very important in this ZB-2510 Series User Manual, Ver. 1.2 Page 10... - Page 11 *4: The user can define this value based on the system environment. The minimum timeout is 4 seconds. The network will attempt to forward the data to the secondary route if there is a problem with the ZigBee network. ZB-2510 Series User Manual, Ver. 1.2 Page 11...
-
Page 12: Applications
If a repeater at any of the locations is invalid, the data transmission route will be switched to the back-up route based on the user-defined timeout so that the ZigBee network transmission can be recovered. ZB-2510 Series User Manual, Ver. 1.2 Page 12... - Page 13 If the distance between two intersections is beyond the ZigBee DIO module’s default transmission range, a ZigBee repeater can be added to extend the transmission range. ZB-2510 Series User Manual, Ver. 1.2 Page 13...
-
Page 14: Quick Start For The Zb-2510 Series
5. Quick Start for the ZB-2510 Series 5.1 Installing the ZB-2000 Driver 1. Download the file from: http://ftp.icpdas.com/pub/cd/usbcd/napdos/zigbee/zigbee_repeater/zb_2510/driver/ 2. Uncompress the file and double click the ZB-2000 DriverInstaller.exe file to install the driver for the ZigBee repeater. 3. When the following screen is displayed, click the Next> button to continue the installation, or click Cancel exit the installation. - Page 15 5. When the following screen is displayed, click the Continue Anyway button to continue the installation, or click STOP Installation exit the installation. 6. When the following screen is displayed, click the Finish button to finalize the software installation. ZB-2510 Series User Manual, Ver. 1.2 Page 15...
-
Page 16: Installing The Hardware And Driver
2. Windows will detect the new device and will initiate “the Found New Hardware Wizard” prompting you to install the software for the detected USB Device. Select the “Yes, now and every time I connect a device” option. Click the Next to button continue. ZB-2510 Series User Manual, Ver. 1.2 Page 16... - Page 17 (Advanced)” Option, then click the Next> button to continue the installation, or click the Cancel button exit the installation. 4. Browse to \\Napdos\ZigBee\ZigBee_Repeater\ZB_2510\Driver\ZB2000_Driver to locate the installation file, and click the Next button to begin the search. ZB-2510 Series User Manual, Ver. 1.2 Page 17...
- Page 18 STOP Installation exit the installation. 6. When the following screen is displayed, click the Finish button to finalize the software installation. NOTE: When the driver installation is complete, unplug the USB cable, and then reconnect it. ZB-2510 Series User Manual, Ver. 1.2 Page 18...
- Page 19 7. Right click on My Computer and select Properties. 8. Select Device Manager from the System Properties dialog box. 9. Confirm whether the ZB-2000 (COM Number) is listed in the ports section. ZB-2510 Series User Manual, Ver. 1.2 Page 19...
-
Page 20: Installing The Configuration Tool
2. Double click the setup_zigbee_configuration_utility_ver_5.x.x.exe file to install the configuration tool for the ZigBee repeater. 3. When the following screen is displayed, click the Next> button to continue the installation, or click Cancel exit the installation. ZB-2510 Series User Manual, Ver. 1.2 Page 20... - Page 21 ‘Change...’ button to install into an alternate location. Click the ‘Cancel’ button to quit the installation. 5. When the following screen is displayed, click the Finish button to finalize the software installation. ZB-2510 Series User Manual, Ver. 1.2 Page 21...
-
Page 22: Quick Configuration For The Zb-2510 Series
5.4 Quick Configuration for the ZB-2510 Series 1. Hardware Installation: ZB-2510 Series PC-base Terminal CA-USB18 2. After installing the ZigBee_Configuration_Utility_Ver_5.x.x, the executable file can be found at: Start:\ICPDAS\ZigBee_Configuration_Utility_Ver5.x.x 3. When the following screen is displayed: Environment Settings In the section: 1. - Page 23 Configure button. 2. When the following alert is displayed, it means that the configuration has been successful. Click the button to continue the other configurations or click button to exit configuration. ZB-2510 Series User Manual, Ver. 1.2 Page 23...
-
Page 24: Appendix
1 km (Max.) ZB-100R/ZB-100T Supported Supports Max. Slaves (Host) Certification CE/FCC,FCC ID 2. Set to Default: In the set parameters dialog box (step 5 above.), click the default buttom.Click the Default button. ZB-2510 Series User Manual, Ver. 1.2 Page 24... - Page 25 2. The ZB-2510 Series default settings: Pan ID 00 01 Node ID 00 01 RF Channel Network Presence Detection Time 20 sec Interval Route Paths Options Broadcast Mode 3. Network Status Detection Time Setting: If setting value is 20, it means every 20 seconds a packet will be send to confirm the status of the network.
- Page 26 \Napdos\ZigBee\ZigBee_Repeater\ZB_2510\Document\ 7. Driver download location: Website: http://ftp.icpdas.com/pub/cd/usbcd/napdos/zigbee/zigbee_repeater/zb_2510/ driver/ CD path: \Napdos\ZigBee\ZigBee_Repeater\ZB_2510\Driver\ 8. ZigBee Products website: http://www.icpdas.com/products/GSM_GPRS/wireless/solutions.htm#6 9. Technical Service: If you have any questions, send a description of your problem to: service@icpdas.com ZB-2510 Series User Manual, Ver. 1.2 Page 26...
-
Page 27: Ordering Information
High Power Amplifier ZigBee Repeater (RoHS) + GPSU06U-6 (Power Supply) ZB-2510-T CR ZigBee Repeater (RoHS) ZB-2510-T/S CR ZigBee Repeater (RoHS) + GPSU06U-6 (Power Supply) ZB-2510-PA CR ZigBee Repeater (RoHS) ZB-2510-PA/S CR ZigBee Repeater (RoHS) + GPSU06U-6 (Power Supply) ZB-2510 Series User Manual, Ver. 1.2 Page 27... -
Page 28: Accessories
Wireless 6-ch Isolated Digital Input and 4-ch Relay Output Module ZB-2060-T Wireless 6-ch Isolated Digital Input and 4-ch Relay Output Module (CE/FCC/FCC ID) ZB-2060-PA Wireless 6-ch Isolated Digital Input and 4-ch Relay Output Module (long range) ZB-2510 Series User Manual, Ver. 1.2 Page 28...
Need help?
Do you have a question about the ZB-2510 and is the answer not in the manual?
Questions and answers