1. Manuals
  2. Brands
  3. Videosec Manuals
  4. Security Camera
  5. ICS-20F
  6. User manual

Videosec ICS-20F User Manual

Full hd ip box camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Full HD IP Box Camera

User Manual

Ver1.4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ICS-20F and is the answer not in the manual?

Questions and answers

Related Manuals for Videosec ICS-20F

Summary of Contents for Videosec ICS-20F

  • Page 1: User Manual

    Full HD IP Box Camera User Manual Ver1.4...

  • Page 2: Table Of Contents

    Table of Contents Introduction.........................3 Features ........................3 Package Contents ......................4 Camera Overview......................5 Preparations for IP Camera Setup ................7 System Requirements ....................7 Installation ........................8 Deleting the Existing DC Viewer ................10 Accessing Camera ....................13 Configuration & Operation..................19 Browser-based Viewer Introduction ................19 Home Page .........................
  • Page 3 5.3.18 Factory Default .................... 74 5.3.19 Software Version ..................75 5.3.20 Software Upgrade..................76 5.3.21 Maintenance ....................79 Video and Audio Streaming Settings................81 5.4.1 Video Resolution and Rotate Type .............. 81 5.4.2 Video Compression ..................84 5.4.3 Video OCX Protocol..................86 5.4.4 Video Frame Skip ..................

  • Page 4: Introduction

    Introduction Following high standard of Megapixel IP Camera, the Full HD IP Camera is capable of serving real-time streaming and makes image quality more smoothly. Compare with our HD WDR IP Camera product line, Full HD IP Camera offer a more economical solution to serve 2 Megapixel resolution.

  • Page 5: Package Contents

    Package Contents Please check the package contains the following items listed below. Full HD Multi-Res IP Camera Back focus adjuster Quick Guide (bundled software and documentation)

  • Page 6: Camera Overview

    Camera Overview DC 12V/ PoE Network LEDs Power LED Reset Button Definition Remarks LINE OUT & LINE IN / MIC IN Two-way audio transmission Power LED Power connection indication (green light) Reset button Reset to factory default AUTO IRIS connector Auto iris lens connector NETWORK (with PoE) RJ-45 connector...
  • Page 7 Dimensions...

  • Page 8: Preparations For Ip Camera Setup

    Preparations for IP Camera Setup This chapter provides information about system requirements for IP Camera operation, power connection, Ethernet connection and ways to access to the camera. System Requirements To perform the IP Camera via web browser, please ensure your PC is in good network connection, and meet system requirements as described below.

  • Page 9: Installation

    Installation Please follow the instructions below to complete IP Camera installation. Lens Mounting: C/CS Mount Lens Model If use C-Mount lens, after removing the camera’s plastic cover, users need to mount the C/CS mount adapter to the camera. Then attach the lens onto the C/CS mount adapter, as the illustrations shown below.
  • Page 10 Alarm Application The camera equips one alarm input and one relay output for alarm application. Refer to alarm pin definition below to connect alarm devices to the IP Camera if needed. PIN 1: Output+ PIN 2: Output- PIN 3: Input+ PIN 4: Input- RS-485 Connector (Optional for DC12V/AC24V/PoE Model) The RS-485 connector is the interface for connecting with the pan &...

  • Page 11: Deleting The Existing Dc Viewer

    Deleting the Existing DC Viewer For users who have installed the DC Viewer in the PC previously, please first delete the existing DC Viewer from the PC before accessing to this IP Camera. Deleting the DC Viewer Click “Control Panel”, and then double click “Add or Remove Programs.” In the “Currently installed programs”...
  • Page 12 STEP 1: Click the “Tools” tab and select the option “Internet Options.” STEP 2: Click on “Delete”, then tap the “Delete Files” in the “Temporary Internet files” section.
  • Page 13 The popup window for confirmation will come out as shown below. Click “OK” to start deleting the files.

  • Page 14: Accessing Camera

    Accessing Camera For initial access to the IP Camera, users can search the camera through the installer program: DeviceSearch.exe, which can be found in “DeviceSearch” folder in the supplied CD. Device Search Software Setup Step 1: Double click on the program Device Search.exe (see the icon below); its window will appear as shown below.
  • Page 15 Device Search Step 3: Click “Device Search” again, and all the finding IP devices will be listed in the page, as shown in the figure below. The IP Camera’s default IP address is: 192.168.0.250. Step 4: Double click or right click and select “Browse” to access the camera directly via web browser.
  • Page 16 The default login ID and password for the Administrator are: Login ID Password Admin 1234 NOTE: ID and password are case sensitive. NOTE: It is strongly advised that administrator’s password be altered for the security concerns. Refer to section 5.3.2 Security for further details.
  • Page 17 Step 2: The “Network Setup” page will come out. Select “DHCP,” and press “Apply” button down the page. Step 3: Click “OK” on the Note of setting change. Wait for one minute to re-search the IP Camera. Step 4: Click the “Device Search” button to search all the devices. Then select the IP Camera with the correct MAC address.
  • Page 18 Installing DC Viewer Software Online For the initial access to the IP Camera, a client program, DC Viewer, will be automatically installed to your PC when connecting to the IP Camera. If the Web browser doesn’t allow DC Viewer installation, please check the Internet security settings or ActiveX controls and plug-ins settings (see Appendix B: Internet Security Settings) to continue the process.
  • Page 19 Administrator/User Privileges “Administrator” represents the person who can configure the IP Camera and authorize users access to the camera; “User” refers to whoever has access to the camera with limited authority, i.e. entering Home and Camera setting pages. Image and Focus Adjustment The image displays on the Home page when successfully accessing to the IP Camera.

  • Page 20: Configuration & Operation

    Configuration & Operation The IP Camera is provided with a user-friendly browser-based configuration interface, as well as a free bundled CMS (Central Management System) for video playback and recording. In this chapter, information about main page introduction, system related settings and camera settings will be described in detail.
  • Page 21 There are five tabs: Home, System, Streaming, Camera and Logout on the top panel. Home Users can monitor live video of the targeted area. System setting The administrator can set host name, system time, root password, network related settings, etc. Further details will be interpreted in section 5.3 System Related Settings.

  • Page 22: Home Page

    Home Page In the Home page, there are several function buttons right down the displayed image. NOTE: Please note that the function buttons will vary depending on the camera model. Multiple Languages Support Multiple languages are supported, including German, English, French, Italian, Russian, etc., for the viewer window interface.
  • Page 23 (on/off) Talk button Talk function allows the local site to talk to the remote site. Click on the button to switch it to on/off. Please refer to section 5.3.2 Security: Add user >> Talk/Listen for further details. This function is only open to “User” who has been granted this privilege by the Administrator.

  • Page 24: System Related Settings

    System Related Settings The figure below shows all categories under the “System” tab. Each category in the left column will be explained in the following sections. NOTE: The “System” configuration page is only accessible by the Administrator.

  • Page 25: Host Name And System Time Setting

    5.3.1 Host Name and System Time Setting Press the first category: <System> in the left column; the page is shown as below. Host Name The name is for camera identification. If alarm function(see section 5.3.8 Application) is enabled and is set to send alarm message by Mail/ FTP, the host name entered here will display in the alarm message.

  • Page 26: Security

    Manual The Administrator can set video date, time and day manually. Entry format should be identical with that shown next to the enter fields. Sync with NTP server Network Time Protocol (NTP) is an alternate way to synchronize your camera’s clock with a NTP server.

  • Page 27: User

    5.3.2.1 User Click the <User> tab under the category <Security> and the page is shown as the figure below. Root password Change the administrator’s password by inputting the new password in both text boxes. The input characters/numbers will be displayed as dots for security purposes.
  • Page 28 • I/O access This item supports fundamental functions that enable users to view video when accessing to the camera. • Camera control This item allows the specified User to change camera parameters on the Camera Setting page. • Talk/Listen Talk and Listen functions allow the appointed user in the local site (PC site) communicating with, for instance, the administrator in the remote site.

  • Page 30: Https

    5.3.2.2 HTTPS <HTTPS> allows secure connections between the IP Camera and web browser using <Secure Socket Layer (SSL)> or <Transport Layer Security (TLS)>, which ensure camera settings or Username/ Password info from snooping. It is required to install a self-signed certificate or a CA-signed certificate for implementing <HTTPS>.
  • Page 31 Create Self-signed Certificate Before a CA-issued certificate is obtained, users can create and install a self-signed certificate first. Click <Create> button under “Create self-signed certificate” and provide the requested information to install a self-signed certificate for the IP Camera. Please refer to the last part of this section: Provide the Certificate Information for more details.
  • Page 32 Create Certificate Request Click the “Create Certificate Request” button to create and submit a certificate request in order to obtain a signed certificate from CA. Provide the request information in the create dialog. Please refer to the following Provide the Certificate Information for more details When the request is complete, the subject of the Created Request will be shown in the field.
  • Page 33 Provide the Certificate Information To create a Self-signed HTTPS Certificate or a Certificate Request to CA, please enter the information as requested:...
  • Page 34 • Country Enter a 2-letter combination code to indicate the country the certificate will be used in. For instance, type in “US” to indicate United States. • State or province Enter the local administrative region. • Locality Enter other geographical information. •...

  • Page 35: Ip Filter

    • Valid days (Self-signed Certificate Only) Enter the period in days (1~9999) to indicate the valid period of certificate. Click “OK” to save the Certificate Information after complete. 5.3.2.3 IP Filter Using the IP filter, access to the IP Camera can be restricted by denying/allowing specific IP addresses.

  • Page 36: Ieee 802.1X

    • Add/ Delete IP Address Input the IP address and click the <Add> button to add a new filtered address. The Filtered IP Addresses list box shows the currently configured IP addresses. Up to 256 IP address entries may be specified. To remove an IP address from the list, please select the IP and then click the <Delete>...
  • Page 37 CA Certificate The CA certificate is created by the Certification Authority for the purpose of validating itself. Upload the certificate for checking the server’s identity. Client Certificate/ Private Key Upload the Client Certificate and Private Key for authenticating the IP Camera itself.

  • Page 38: Network

    5.3.3 Network Click the category: < Network>, there will be a drop-down menu with tabs including <Basic>, <QoS>, <SNMP>, and <UPnP>.

  • Page 39: Basic

    5.3.3.1 Basic Users can choose to connect to the IP Camera with fixed or dynamic (DHCP) IP address. The IP Camera also provides PPPoE (Point-to-Point Protocol over Ethernet) support for users who connect to the network via PPPoE. Get IP address automatically (DHCP) The camera’s default setting is “Use fixed IP address”.
  • Page 40 Use fixed IP address To setup static IP address, select “Use fixed IP address” and move the cursor to the IP address blank (as indicated below) and insert the new IP address, ex. 192.168.7.123; then go to the Default gateway (explained latter) blank and change the setting, ex.
  • Page 41 • Default gateway This is the gateway used to forward frames to destinations in different subnet. Invalid gateway setting will fail the transmission to destinations in different subnet. • Primary DNS Primary DNS is the primary domain name server that translates hostnames into IP addresses.

  • Page 42: Qos (Quality Of Service)

    IPv6 Address Configuration With IPv6 support, users can use the corresponding IPv6 address for browsing. Enable IPv6 by checking the box and click “Save” to complete the setting. 5.3.3.2 QoS (Quality of Service) QoS allows providing differentiated service levels for different types of traffic packets, which guarantees delivery of priority services especially when network congestion occurs.
  • Page 43 The IP Camera uses the following QoS Classes: Video, Audio and Management. • Video The class consists of applications such as MJPEG over HTTP, RTP/RTSP and RTSP/HTTP. • Audio This setting is only available for the IP Cameras that support audio. •...

  • Page 44: Snmp (Simple Network Management Protocol)

    5.3.3.3 SNMP (Simple Network Management Protocol) With Simple Network Management Protocol (SNMP) support, the IP Camera can be monitored and managed remotely by the network management system. SNMP v1/ v2 • Enable SNMP Select the version of SNMP to use by checking the box. •...

  • Page 45: Upnp

    Traps for SNMP v1/ v2 Traps are used by the IP Camera to send massages to a management system for important events or status changes. • Enable Traps Check the box to activate trap reporting. • Trap address Enter the IP address of the management server. •...
  • Page 46 UPnP Setting • Enable UPnP When the UPnP is enable, whenever the IP Camera is presented to the LAN, the icon of the connected IP Cameras will appear in My Network Places to allow for direct access as shown below.
  • Page 47 NOTE: To enable this function, please make sure the UPnP component is installed on your computer. Please refer to Appendix E: Install UPnP components for UPnP component installation procedure. • Enable UPnP port forwarding When the UPnP port forwarding is enabled, the IP Camera is allowed to open the web server port on the router automatically.

  • Page 48: Ddns

    5.3.4 DDNS Dynamic Domain Name System (DDNS) allows a host name to be constantly synchronized with a dynamic IP address. In other words, it allows those using a dynamic IP address to be associated to a static domain name so others can connect to it by name.

  • Page 49: Mail

    Password/Key Enter the password or key required by the DDNS provider for authentication. 5.3.5 Mail The Administrator can send an e-mail via Simple Mail Transfer Protocol (SMTP) when motion is detected. SMTP is a protocol for sending e-mail messages between servers. SMTP is a relatively simple, text-based protocol, where one or more recipients of a message are specified and the message text is transferred.

  • Page 50: Ftp

    5.3.6 The Administrator can set as sending alarm message to a specific File Transfer Protocol (FTP) site when motion is detected. Users can assign alarm message to up to two FTP sites. The FTP setting page is shown below. Enter the FTP details, which include server, server port, user name, password and remote folder, in the fields.

  • Page 51: Http

    5.3.7 HTTP A HTTP Notification server can listen for notification messages from IP Cameras by triggered events. The HTTP setting page is shown below. Enter the HTTP details, which include server, user name, and password in the fields. <Alarm> triggered and <Motion Detection> notifications can be sent to the specified <HTTP>...

  • Page 52: Application

    5.3.8 Application The IP Camera equips one alarm input and one relay output for cooperating with alarm system to catch events’ images. Refer to alarm pin definition below to connect alarm devices to the IP Camera if needed. The alarm configuration page is also shown below.
  • Page 53 Alarm Output Define alarm output signal “high” or “low” as the normal alarm output status according to the current alarm application. Triggered Action (Multi-option) The Administrator can specify alarm actions that will take when the alarm is triggered. All options are listed as follows: •...
  • Page 54 • Record Stream to SD Card Select the item, and the alarm-triggered recording will be saved into your Micro SD card. NOTE: Please make sure the local recording (with Micro SD/ SDHC card) is activated so that this function can be implemented. See section 5.3.12 Recording for further details.
  • Page 55 • Upload Image by E-Mail Select this item, and the Administrator can assign an e-mail address and configure various parameters as shown in the figure below. When the alarm is triggered, event images will be sent to the appointed e-mail address.
  • Page 56 • Send HTTP notification Check this item, select the destination HTTP address, and specify the parameters for event notifications by <Alarm> triggered. When an alarm is triggered, the notification can be sent to the specified HTTP server. File Name Enter a file name in the blank, ex. image.jpg. The uploaded image’s file name format can be set in this section.
  • Page 57 • Add sequence number suffix (limited value) File Name: imageXX.jpg X: Sequence Number The file name suffix will end at the number being set. For example, if the setting is up to “10,” the file name will start from 00, end at 10, and then start all over again.

  • Page 58: Motion Detection

    5.3.9 Motion Detection Motion Detection function allows detecting suspicious motion and triggering alarms when motion volume in the detected area reaches/exceeds the determined sensitivity threshold value. In the Motion Detection setting page, there is a frame (Motion Detection Window) displayed on the Live View Pane. The Motion Detection Window is for defining the motion detection area.
  • Page 59 If Motion Detection function is activated, the pop-off window (Motion) with indication of motion will be shown. When motion is detected, the signals will be displayed on the Motion window as shown below. Detailed settings of Motion Detection are described as follows: Motion Detection You will be able to turn on/off Motion Detection in System section.
  • Page 60 • Sensitivity level [1-100]: The default level is 80, which means if 20% or more sampling pixels are detected differently, system will detect motion. The bigger the value, the more sensitive it is. Meanwhile, when the value is bigger, the red horizontal line in the motion indication window will be lower accordingly.
  • Page 61 • Upload Image by E-Mail Select this item, and the Administrator can assign an e-mail address and configure various parameters as shown in the figure below. When motion is detected, event images will be sent to the appointed e-mail address. NOTE: Make sure SMTP or FTP configuration has been completed.

  • Page 62: Tampering

    5.3.10 Tampering Tempering Alarm function helps the IP Camera against tampering such as deliberate redirection, blocking, paint spray, and lens cover, etc through video analysis and reaction to such events by sending out notifications or uploading snapshots to the specified destination(s). Detection of camera tampering is achieved by measuring the differences between the older frames of video (which are stored in buffers) and more recent frames.
  • Page 63 higher threshold. Settable Tampering Duration time range is from 10 to 3600 seconds. Triggered Action (Multi-option) The Administrator can specify alarm actions that will take when tampering is detected. All options are listed as follows: • Enable Alarm Output Check the item and select the predefined type of alarm output to enable alarm relay output when tampering is detected.
  • Page 64 • Upload Image by E-Mail Select this item, and the Administrator can assign an e-mail address and configure various parameters as shown in the figure below. When tampering is detected, event images will be sent to the appointed e-mail address. NOTE: Make sure SMTP or FTP configuration has been completed.

  • Page 65: Storage Management

    5.3.11 Storage Management Users can implement local recording to the Micro SD/SDHC card up to 16GB. This page shows the capacity information of the Micro SD card and a recording list with all the recording files saved on the memory card. Users can also format the SD card and implement automatic recording cleanup through the setting page.
  • Page 66 For the memory card being successfully installed, its status shall be shown at “Device information” section in the Storage Management page. Device setting Press the “Format” button to format the memory card. Disk cleanup setting Users can enable automatic recordings cleanup by specifying the time and storage limits.
  • Page 67 • Download To open/download a video clip, select the file first, and then press the “download” button below the Recording list field. The selected file window will pop up as shown below. Click on the AVI file to directly play the video in the player or download it to a specified location.

  • Page 68: Recording

    5.3.12 Recording In the Recording setting page, users can specify the recording schedule that fits the present surveillance requirement. Activating Micro SD/SDHC Card Recording Two types of schedule mode are offered: Always and Time Frame setting. Users can setup the time frame to fit the recording schedule or choose “Always” to activate Micro SD/SDHC Card Recording all the time.

  • Page 69: File Location

    5.3.13 File Location Users can specify a storage location for the snapshots and Web recording. The default setting is: C:\. Once confirm the setting, press “Save,” and all the snapshots and recording will be saved in the designate location. NOTE: Please make sure the selected file path contains valid characters such as letters and numbers.

  • Page 70: Iris Adjustment

    5.3.14 Iris Adjustment For users who use Auto-iris lens, when it is required to implement iris adjustment, please refer to the Iris adjustment procedure in the setting page to adjust iris.

  • Page 71: View Log File

    5.3.15 View Log File Click on the link to view the system log file. The content of the file provides useful information about configuration and connections after system boot-up.

  • Page 72: View User Information

    5.3.16 View User Information The Administrator can view each added user’s login information and privileges (see 5.3.2 Security). View User Login Information All the users in the network will be listed in the “User information” zone, as shown below. As the figure below shows: User: 4321 It indicates that one user’s login username is: User, and the password is: 4321.
  • Page 73 View User Privilege Press “get user privacy” down the page, and the Administrator can view each user’s privileges. As the figure above shows: User: 1:1:0:1 1:1:0:1= I/O access : Camera control : Talk : Listen (see 5.3.2 Security) Therefore, it denotes the user is granted privileges of I/O access, Camera control and Listen.

  • Page 74: View Parameters

    5.3.17 View Parameters Click on this item to view the entire system’s parameter setting.

  • Page 75: Factory Default

    5.3.18 Factory Default The factory default setting page is shown as below. Follow the instructions to reset the IP Camera to factory default setting if needed. Set Default Click on the “Set Default” button to recall the factory default settings. Then the system will restart in 30 seconds.

  • Page 76: Software Version

    5.3.19 Software Version The current software version is displayed in the software version page, which is shown as the figure below.

  • Page 77: Software Upgrade

    5.3.20 Software Upgrade Software upgrade can be carried out in the “Software Upgrade” page, as shown below. NOTE: Make sure the upgrade software file is available before carrying out software upgrade.
  • Page 78 The procedure of software upgrade is like the following: Step 1: Click “Browse” and select the binary file to be uploaded, ex. Userland.jffs2. NOTE: Do not change the upgrade file name, or the system will fail to find the file. Step 2: Pull down the upgrade binary file list and select the file you want to upgrade;...
  • Page 79 After the upgrade process is finished, the viewer will return to Home page. Step 4: Close the video browser. Step 5: Click “Control Panel”, and then double click “Add or Remove Programs.” In the “Currently install programs” list, select “DCViewer” and click the button “Remove”...

  • Page 80: Maintenance

    5.3.21 Maintenance Users can export configuration files to a specified location and retrieve data by uploading an existing configuration file to the IP Camera. Export Users can save the system settings by exporting the configuration file (.bin) to a specified location for future use. Press the “Export” button, and the popup File Download window will come out as shown below.
  • Page 81 Upload To copy an existing configuration file to the IP Camera, please first click on “Browse” to select the configuration file, and then press the “Upload” button for uploading.

  • Page 82: Video And Audio Streaming Settings

    Video and Audio Streaming Settings Press the tab ”Streaming” in the top of the page, and the configurable video and audio items will display in the left column. In Streaming, the Administrator can configure specific video resolution, video compression mode, video protocol, audio transmission mode, etc.
  • Page 83 Video Format Resolution for MJPEG & H.264 format includes: • H.264 720p (30fps) + MJPEG 720p (30fps) • H.264 720p (30fps) + MJPEG D1 (30fps) • H.264 720p (30fps) + MJPEG CIF (30fps) • H.264 720p (30fps) + MJPEG VGA (30fps) •...
  • Page 84 To rotate the image, users can select “Flip”, for instance. Then the displayed image will be reversed as shown below. The following is descriptions for different video rotate type. • Flip If select <Flip>, the image will be rotated vertically. •...

  • Page 85: Video Compression

    5.4.2 Video Compression Users can specify the values for MJPEG/ H.264 compression in the video Compression page (see the figure below), depending on the application. MJPEG Q (Quality) factor Higher value implies higher bit rates and higher visual quality. The default setting of MJPEG Q factor is 35;...
  • Page 86 CBR Mode Setting The CBR (Constant Bit Rate) mode could be the preferred bit rage mode if the bandwidth available is limited. It is important to take account of image quality while choosing to use CBR mode.

  • Page 87: Video Ocx Protocol

    5.4.3 Video OCX Protocol In the Video OCX protocol setting page, users can select RTP over UDP, RTP over TCP, RTSP over HTTP or MJPEG over HTTP, for streaming media over the network. In the case of multicast networking, users can select the Multicast mode.

  • Page 88: Video Frame Skip

    5.4.4 Video Frame Skip Video frame skipping is for saving bandwidth if necessary. The setting page is shown as below. Video Frame Skip options include: • No skipping, default • Frame skipping at 2 frame internal • Frame skipping at 3 frame internal •...

  • Page 89: Video Mask

    5.4.5 Video Mask Active Mask Function • Add a Mask Check a Video Mask checkbox, and a red frame will come out in the Live Video pane at the right side. Use the mouse to drag and drop to adjust the mask’s size and place it on the target zone.

  • Page 90: Audio Mode And Bit Rate Settings

    • Type Select to change the mask type as solid or transparent. Click “Save” to confirm the setting. 5.4.6 Audio Mode and Bit Rate Settings The audio setting page is show as below. In the Audio page, the Administrator can select one transmission mode and audio bit rate. Transmission Mode •...
  • Page 91 • Simplex (Talk only) In the Talk only Simplex mode, the local/remote site can only talk to the other site. • Simplex (Listen only) In the Listen only Simplex mode, the local/remote site can only listen to the other site. •...

  • Page 92: Camera Settings

    Camera Settings The figure below is the camera configuration page. Details of each parameter setting are described in the following subsections. NOTE: Camera settings and function buttons will vary depending on the camera model.

  • Page 93: Exposure Setting

    5.5.1 Exposure Setting The Exposure pull-down menu is shown as follows: The exposure is the amount of light received by the image sensor and is determined by the width of lens diaphragm opening, the amount of exposure by the sensor (shutter speed) and other exposure parameters. With this item, users can define how the Auto Exposure function works.

  • Page 94: White Balance Setting

    Fixed Shutter Mode In this mode, fixed shutter speed could be selected from the dropdown menu. The shutter speed range is from 1/10000 to 1 (1/1.5) sec. with 19 (18) options. Users could select suitable shutter speed according to the environmental illumination.

  • Page 95: Brightness Setting

    Manual Mode In this mode, users can change the White Balance value manually. Users can select a number between 0 ~127 of “Rgain/ Bgain” item to gain the red/ blue illuminant on the Live Video Pane. Press < √ > to confirm the new setting. 5.5.3 Brightness Setting Users can adjust the image’s brightness by adjusting the item.

  • Page 96: Hue Setting

    5.5.7 Hue Setting Camera image hue level is adjustable; please select ranging from -12 to +13. Press < √ > to confirm the new setting. 5.5.8 TV System Setup Select the video format that matches the present TV system. Press < √ > to confirm the new setting.

  • Page 97: Logout

    Logout Press the tab “Logout” in the top of the page, and the login window will pop up. This enables login with another user name.

  • Page 98: Cms Software Introduction

    Appendix A: Technical Specifications Camera Full HD Real time Full HD Image Sensor 1/2.7" Progressive CMOS Picture Elements 1920(H) x 1080(V) Color 0.2 lux @ F 1.2 Minimum Illumination 0.02 lux @ F 1.2 Shutter Speed 1~ 1/10000 sec. White Balance Manual / AWB / ATW Lens C/CS mount Lens...
  • Page 99 Security HTTPS, IP Filter Mechanical Lens Mounting C / CS mount Power DC jack Ethernet RJ-45 Micro SD; optional SDHC support Stereo phone jack, ∅ 3.5 mm Audio Connectors Alarm 4 pins terminal block, pitch 3.5 mm Auto Iris (optional) DC Drive Analog Video (optional) 1.0 Vp-p / 75Ω, BNC...

  • Page 100: Appendix B: Internet Security Settings

    Appendix B: Internet Security Settings If ActiveX control installation is blocked, please either set Internet security level to default or change ActiveX controls and plug-ins settings. Internet Security Level: Default Step 1: Start the Internet Explorer (IE). Step 2: Select <Tools> from the main menu of the browser. Then Click <Internet Options>. Step 3: Click the <Security>...
  • Page 101 Step 4: Down the page, press “Default Level” (see the figure above) and click “OK” to confirm the setting. Close the browser window, and open a new one later when accessing the IP Camera. ActiveX Controls and Plug-ins Settings Step 1~3: Refer to the previous section above. Step 4: Down the page, press “Custom Level”...
  • Page 102 The Security Settings screen is displayed as below: Step 5: Under “ActiveX controls and plug-ins”, set ALL items (as listed below) to <Enable> or <Prompt>. ActiveX controls and plug-ins settings: 1. Automatic prompting for ActiveX controls 2. Binary and scrip behaviors 3.

  • Page 103: Appendix C: Dc Viewer Download Procedure

    Appendix C: DC Viewer Download Procedure The procedure of DC Viewer software download is specified as follows. Step 1: In the DC Viewer installation page, click “Next” for starting installing. Step 2: Setup starts. Please wait for a while until the loading bar runs out.
  • Page 104 Step 3: Click “Finish” to close the DC Viewer installation page. Then, the IP Camera’s Home page will display as follows: NOTE: Please note that the function buttons will vary depending on the camera model.

  • Page 105: Appendix D: Back Focus Adjustment

    Appendix D: Back Focus Adjustment When to adjust back focus Back Focus refers to the distance from the rear lens element to the camera focal plane. In most cases, it is required to adjust back focus only when the camera’s lens cannot hold focus throughout its zoom range, What requirements Tools required when carrying out back focus adjustment include:...

  • Page 106: Appendix E: Install Upnp Components

    Appendix E: Install UPnP Components Please follow the instructions below to install UPnP components. Step 1: Go to “Start”, click on “Control Panel”, and then double click “Add or Remove Programs”. Step 2: Click on “Add/Remove Windows Components” in the Add or Remove Programs page..
  • Page 107 Step 3: Select “Networking Services” from the Components list in the Windows Components Wizard window, and then click “Details”. Step 4: Select “UPnP User Interface” in the Networking Services’ subcomponents list and then click “OK”.
  • Page 108 Step 5: Click “Next” in the Windows Components Wizard page. Step 6: Click “Finish” to complete installation.

Table of Contents