Service; Features; Removing; Fitting - Black & Decker Planer Manual

g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from those intended could result
in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions for planers
Wait for the cutters to stop before setting the tool
N
down. An exposed cutter may engage the surface and
lead to possible loss of control and serious injury.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
This appliance is not intended for use by young or infirm
N
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
N
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
3. Shavings discharge outlet
4. Planing depth adjustment knob
5. Planing depth graduation
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Replacing the cutting blades (fig. A)
The cutting blades provided with this tool are reversible.
Replacement cutting blades can be obtained from your local
retailer.

Removing

Loosen the bolts (6) using the spanner supplied.
N
Slide the blade (7) out of the holder (8).
N
Reverse the blade so that the unused side comes in position.
N
If both sides are worn, the blade must be replaced.
6

Fitting

Slide the blade into the holder until it is centred in the holder.
N
Make sure that the holder remains centred in the barrel (9).
N
Tighten the bolts using the spanner supplied.
N
Always replace both cutters.
N
Adjusting the depth of cut (fig. B)
The depth of cut is indicated by the marking (10). The setting
range can be read from the graduation (5).
Turn the planing depth adjustment knob (4) to the required
N
depth of cut.
Turn the knob to the 'P' postion whenever the tool is not in use.
N
Fitting and removing the parallel fence (fig. C)
The parallel fence (11) is used for optimum control on narrow
workpieces.
Hold the parallel fence (11) in front of the tool as shown.
N
Fit the parallel fence by inserting the locking knob (12)
N
into the hole (13).
Tighten the locking knob.
N
To remove the parallel fence proceed in reverse order.
N
Fitting and removing the rebating depth stop (fig. D)
The rebating depth stop (15) is used for limiting the planing
depth during rebating.
Hold the stud (16) in front of the tool as shown.
N
Fit the rebating depth stop by inserting the locking knob (17)
N
into the hole (18).
Fasten the locking knob.
N
To remove the rebating depth stop proceed in reverse order.
N
Adjusting the shavings discharge outlet (fig. E)
The tool facilitates both left-hand and right-hand side
shavings discharge.
Insert the adaptor (19) into the desired outlet opening,
N
aligning the notch with the recess. Twist the adaptor
clockwise as soon as it is fully inserted.
Insert the plug (20) into the opposite opening, following
N
the above procedure.
Provide for a suitable dust extraction.
N
Fitting and removing the shavings bag (fig. F)
Slide the shavings bag (21) into the shavings discharge
N
outlet (3).
Push the shavings bag into place. Make sure that the lug
N
(22) is correctly located into the hole (23) on the inside of
the shavings bag.
To remove the shavings bag, press the tab (24) and pull
N
the shavings bag out of the outlet.