Yamaha CP4 Stage Reference Manual page 42

02: MIDI
The MIDI screen is used to set the instrument's MIDI-related parameters.
NOTE
Refer to the Appendix section
Parameter name Description
This parameter can be used to set the interface used for exchanging MIDI
messages.
(MIDI IN/OUT)
Settings: MIDI and USB
MIDI: MIDI messages will be exchanged via the [IN] and [OUT] MIDI terminals.
USB: MIDI messages will be exchanged via the [TO HOST] USB terminal.
NOTE
This parameter can be used to turn local control on and off. When "off" is
selected, the stage piano's tone generator is essentially disconnected from
(Local Switch)
its controllers, and no sound will be produced in response to playing of the
keyboard. The stage piano does, however, continue to transmit MIDI
messages when LocalSw has been set to "off", and the tone generator will
continue to produce sound in response to received MIDI messages.
Settings: off (disconnected) and on (connected)
This parameter can be used to specify whether Bank Select and Program
Change MIDI messages are to be exchanged between the stage piano and
(Transmit & Receive
other MIDI devices.
Switch)
Settings: off, pgm, and bank&pgm
off: Neither Bank Select nor Program Change MIDI messages will be transmitted and
received.
pgm (Program Change): Program Change MIDI messages will be transmitted and
received, but Bank Select MIDI messages will not.
bank&pgm (Bank Select & Program Change): Both Bank Select and Program
Change MIDI messages will be transmitted and received.
This parameter can be used to specify whether metronome playback or
tempo-dependent effect parameters should be controlled based on the
(MIDI Synchronization)
stage piano's internal clock or on external clock messages received from a
DAW application on a connected computer or from a connected MIDI
device.
Settings: int, ext, and auto
int (internal): Synchronization is based on the internal clock. Use this setting when
your stage piano is to be used alone or as the master clock source for other
equipment.
ext (external): Synchronization is based on clock messages received via MIDI. Use
this setting when an external device is to be used as master.
auto: Clock messages received via MIDI will be prioritized over the stage piano's
current tempo. If no such messages are received, synchronization will be based on
the internal clock set to the last tempo received via MIDI.
NOTE
This parameter can be used to enable ("on") or disable ("off") the sending of
MIDI Clock messages (i.e., F8 Timing Clock) via the MIDI [OUT] terminal.
(MIDI Clock Out)
Settings: on and off
This parameter can be used to set the channel for transmission and
reception of Performance changes.
(Basic Channel)
Settings: 1 to 16 and off
NOTE
42 CP4 STAGE/CP40 STAGE Reference Manual
(page 50) for more details regarding MIDI.
It is not possible to exchange MIDI messages with another instrument via the
MIDI and USB interfaces at the same time. Be sure, therefore, to set this
parameter correctly in accordance with your equipment setup.
When this parameter is set to "ext", you will need to configure your DAW
application or external MIDI device to send MIDI Clock messages to the CP4
STAGE or CP40 STAGE.
Irrespective of this parameter's setting, the channels for transmission and
reception of Part changes are permanently set to channels 1 to 3 for the CP4
STAGE or channels 1 and 2 for the CP40 STAGE.
Design of the CP4 STAGE & CP40 STAGE
Reference
Performances
Editing Performances
Common Edit Area
01: Chorus Effect
02: Reverb Effect
03: General
04: Name
Part Edit Area
01: Play Mode
02: Filter/EG
03: Effect-A
04: Effect-B
05: Controller
06: Receive Switch
Master Keyboard Area
Job Area
01: Recall
02: Copy
03: Bulk
Store Performance Function
Compare Performance Function
File Area
01: Save
02: Load
03: Rename
04: Delete
05: Format
06: Memory Info
Utility Area
01: General
02: MIDI
03: Controller
04: MasterComp
05: Master EQ
06: Panel Lock
Utility Job Area
01: Factory Set
02: Version
Appendix