Konica Minolta DiMAGE X1 Firmware Update Manual
Camera firmware ver.1.10
Hide thumbs
Also See for DiMAGE X1:
- Instruction manual (58 pages) ,
- (57 pages) ,
- Instruction manual (57 pages)
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
DiMAGE X1 Camera Firmware Ver.1.10
This section explains how to install DiMAGE X1 firmware version 1.10. (Firmware is soft-
ware used internally to control the camera.) Be sure to read through the following explana-
tion before you install the firmware. Do not turn the camera OFF during installation; doing
so could damage the CPU inside the camera.
Contents of update
1. Shortened shutter-release time lag.
(Time period from when the shutter-release button is pressed down fully to when exposure
begins.)
2. Shortened operation time lag.
(Time period from zooming lever is operated to when operation of any other function button
is accepted.)
Target products
This firmware is for use only with the DiMAGE X1 and cannot be used with other products.
If the firmware version is already Ver.1.10, it is not necessary to update the firmware.
(Check the firmware version as shown below.)
www.konicaminoltasupport.com
1
www.konicaminolta.com
Advertisement
Related Manuals for Konica Minolta DiMAGE X1
Summary of Contents for Konica Minolta DiMAGE X1
- Page 1 Target products This firmware is for use only with the DiMAGE X1 and cannot be used with other products. If the firmware version is already Ver.1.10, it is not necessary to update the firmware. (Check the firmware version as shown below.)
- Page 2 Checking the camera firmware version 1. Press the main switch (a) to turn on the camera. 2. Press the menu button (b) to open the recording menu. 3. Press the left/right keys of the controller (c) to high- light the setup menu icon, and press the center but- ton to enter.
- Page 3 Prepare an 8MB or larger SD memory card and insert it in the camera. • Make sure that the SD memory card has been formatted by the camera. Copying via SD memory card reader Copying via DiMAGE X1 (loaded on the Cradle CA- 1) connected to PC •...
- Page 4 Preparing the SD memory card for updating 1. Download the firmware file suitable for your PC after carefully reading the end-user license agreement, and save the file in your PC. The downloaded file is compressed. -Windows- x1v110.exe--636KB Double-click the downloaded file. The file is a self-extracting archive, and decompresses automatically.
- Page 5 Preparing the SD memory card for updating 2. Open the FIRMWARE folder of the SD memory card to confirm that the FIRMWARE.BIN file has been successfully copied. 3. Disconnect the camera from the computer or remove the SD memory card from the card reader. - If you are using Windows Me, 2000 or XP, click the unplug-or-eject-hard- ware icon in the lower right-hand corner of the screen, wait until the safe-to remove-hardware window appears, then remove the SD memory card from...
-
Page 6: How To Update Firmware
How to update firmware Note: When performing the firmware update, use fully charged Lithium-ion Battery NP-1 or the AC Adapter Set (sold separately). When using the AC Adapter Set, be sure not to inadvertently disconnect the camera during the firmware updating procedure, other- wise the camera may be permanently damaged. - Page 7 How to update firmware 5. The updating-completed message appears. Turn the camera off. 6. Turn the camera on by pressing the main switch, to confirm the firmware version. 7. Check that the camera firmware version number has changed to “Ver.1.10”. (See the “Checking the camera firmware version”) •...
- Page 8 How to update firmware 10. When the confirmation screen appears, highlight “Yes” and press the center button of the controller. • In advance of using the prepared SD memory card for recording image, format it via the camera or delete the file/folder prepared for firmware update. Windows and Windows Me, 2000 and XP are registered trademarks of Microsoft Corporation in the U.S.A and other countries.