Download
Share
Print this page
  1. Manuals
  2. Brands
  3. ELPRO Manuals
  4. Switch
  5. SDZ16
  6. Installation and use manual

ELPRO SDZ16 Installation And Use Manual

16x16 sd & audio matrix
Hide thumbs

Advertisement

Quick Links

SDZ16
• Automatic rate selection from 143 to 360Mbit/sec
• External switching reference
• Switching line selectable
• Command by keypad, RS232 or LAN
• 16 recallable presets
• Balanced audio combined
SDZ16 – M 05/03/2007
ELPRO Video Labs s.r.l.
1
Strada della Pronda, 45/B 10142 TORINO – ITALY
Tel.+39 0117701583 – Fax +39 011703751
16x16 SD & AUDIO MATRIX

Advertisement

loading
Need help?

Need help?

Do you have a question about the SDZ16 and is the answer not in the manual?

Questions and answers

Related Manuals for ELPRO SDZ16

Summary of Contents for ELPRO SDZ16

  • Page 1 • Switching line selectable • Command by keypad, RS232 or LAN • 16 recallable presets • Balanced audio combined SDZ16 – M 05/03/2007 ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751...

  • Page 2: Table Of Contents

    Firmware upgrade Technical data 10.0 Notes When installing the SDZ16 unit, please read this handbook carefully. The manufacturer shall not be held responsible for any damage or injury caused by use, even correct, of its products. The data and characteristics of the product may be modified without prior notice.

  • Page 3: Overview

    CE certificate the mains cable SDZ16 is a SD 16x16 digital matrix with associated analog audio. The analog audio’s presence does not exclude the possibility of using SD signal’s digital audio (embedded audio). The user has the possibility to save and recall 16 configurations, via keypad and RS232.

  • Page 4: Power Supply

    Do not remove the cover without unplugging the mains cable. In european countries, SDZ16 requires a 230 Vac 50 Hz power suppling through the mains cable. The socket of the cable must be inserted in the related panel plug on the left at the back of the unit.

  • Page 5: Settings

    SD is usually a 270 Mbit/sec signal (4:2:2 component) as required by ITU-R- 601 normatives, or rather SMPTE 259M. However SDZ16 is able to treat also 143 Mbit/sec (4fsc NTSC), 177 Mbit/sec (4 fsc PAL) and 360 Mbit/sec (4:2:2 widescreen) signals.
  • Page 6 Audio inputs and outputs are balanced. If the source to connect at the input has an unbalanced output, place the hot signal at the a input of the SDZ16, connect the signal’s mass and the b input to the GND.

  • Page 7: Local Control

    Once activated, the Default configuration status will be maintained for all the successive switch ons independently of the active state before switching off. If inactivated, at switch on SDZ16 will maintain the status had at the previous switch off. At switch on, Active Default Configuration is mark ed by the “ Default Status”...
  • Page 8 The switch will be decided pressing the TAKE button. Press the TAKE to effectuate the switch that will be confirmed by the visualization on the display. ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751...
  • Page 9 16x16 SD & AUDIO MATRIX 5.2 SETTINGS USING THE KEY PAD SDZ16 allows some of the settings to be operated using the keypad with the help of an LCD display. To activate settings press FUNCTION. Display shows the writing MENU with its first submenu:...
  • Page 10 This switching state of the SDZ16 becomes Default configuration for all the successive switch ons independently of the active state before switching off. When switched on, in case of an inactive function the SDZ16 will preset itself to the same status had at the previous switch off.
  • Page 11 PC the program it is available in the Software Download section of the mentioned site. SDZ16 must be connected to a PC serial using a f./f. crossed RS232 cable as in the further instructions and the management program must be activated.
  • Page 12 42 30 34 31 30 30 33 0D The SDZ16 matrix replies: (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected ELPRO Video Labs s.r.l.
  • Page 13 Example: To bring video output 15 to high impedance, the following characters must be sent on line: 56 31 35 3030 0D The SDZ16 matrix replies: (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 6.4 AUDIO SWITCHING COMMAND...
  • Page 14 D followed by CR where: D is the character Hex 44 The SDZ16 matrix replies: D (Hex 44) followed by: -N° 32 couples of Hex characters each one representing the video or audio input switched on the output (Each input is represented by 1 couple of ASCII characters).
  • Page 15 30 38 30 38 30 39 30 39 31 30 31 30 31 31 31 31 31 32 31 32 31 33 31 33 31 34 31 34 31 35 31 35 31 36 31 36 31 32 30 30 33 30 30 36 0D ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY...
  • Page 16 52 31 35 0D 6.7 CREATION OF A PRESET (SAVING CURRENT STATUS) The SDZ16 can create and perform up to 16 internal presets. A preset is a predefined configuration of 32 switching points, 16 video and 16 audio, saved in the memory and which can be recalled at any time.
  • Page 17 X indicates if the 16th output must be used as a preview output: 1 = 16 output is a preview output 0 = 16 output is a normal output The SDZ16 matrix replies: (Hex 06) if the command has been performed correctly NACK (Hex 15)
  • Page 18 Once activated the Default configuration status will be maintained for all the successive switch ons independently of the active state before switching off. If inactivated, at switch on SDZ16 will maintain the status had at the previous switch off. At switch on, Active Default Configuration is marked by the “Default Status”...

  • Page 19: Lan Control

    1 ( H ex 31). 7 .0 LAN CONTROL It’s possible to control the SDZ16 through LAN,using the same protocol as in case of the RS232. SDZ16 requires the optional LAN202 for the LAN control possibility. To set the LAN parameters and the SDZ16 available to the...

  • Page 20: Firmware Upgrade

    16x16 SD & AUDIO MATRIX 8.0 FIRMWARE UPGRADE As for all the last generation Elpro products a remote firmware upgrade is available. Such is very useful as also customers that previously aquisted our products may benefit and add the new performances to their equipments.

  • Page 21: Technical Data

    :230Vac / 115Vac (Selectable) Power consumption :20VA Dimensioni (WXDXH) :483X220X132 Weight :4.9Kg Operating temp.range :0÷45° Safety :according to EN60065 :according to EN55103-1 e 55103-2 ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751...

  • Page 22: Note

    During the warranty period, Elpro will repair the faulty units free of charge. The faulty units must be sent CARRIAGE FREE to the Elpro offices in Turin with a regular accompanying note.
  • Page 23 SDZ16 16x16 SD & AUDIO MATRIX YOUR NOTES ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751...
  • Page 24 SDZ16 16x16 SD & AUDIO MATRIX ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751...