Advertisement
Table of Contents
Service manual
Type: WM25
Contents
Introduction .....................................................................................................................................................................................................3
Type overview .................................................................................................................................................................................................4
Programme .......................................................................................................................................................................................................5
Indication of programme sequence ........................................................................................................................................................7
Options and settings .....................................................................................................................................................................................7
Variant settings ...............................................................................................................................................................................................9
Test programme ............................................................................................................................................................................................10
Fault indications............................................................................................................................................................................................12
Components and measurement values ...............................................................................................................................................13
Technical data ................................................................................................................................................................................................15
Circuit diagram ..............................................................................................................................................................................................16
Timer diagram ..............................................................................................................................................................................................18
This service manual describes washing machine type WM25 and is a supplement to the general service
manual for the 600 series.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Asko WM25
Summary of Contents for Asko WM25
-
Page 1: Table Of Contents
Test programme ......................................10 Fault indications......................................12 Components and measurement values ...............................13 Technical data ........................................15 Circuit diagram ......................................16 Timer diagram ......................................18 This service manual describes washing machine type WM25 and is a supplement to the general service manual for the 600 series. - Page 2 Service manual WM25 Revision history Initials Revision Date Description 2008-04-28 WM25.2 can be specified with display, hence change type from WM25.2 to WM25.3 Delayed Start 1-24h implemented W723 CIM motor (brushless)
-
Page 3: Introduction
You are holding the service manual for the WM25 generation of washing machines. There are three types of washing machine in the WM25 series: WM25.1, WM25.2, WM25.3. The following page presents the different versions, to help you identify the machine types. The variants are named differ- ently from market to market. -
Page 4: Type Overview
Service manual WM25 Type overview WM25.1 (USA) Power Stain Colors Perma press Whites Hand/Wool Extra rinses W 6 0 2 2 Q U A T T R O 1 2 0 0 R P M Programme: 4 (For further information, see timer diagram at the foot of the document.) -
Page 5: Programme
Service manual WM25 Programme WM25.1 (USA) Water con- Energy Tempe- Programme Program- Pre- Main Short spin Rinses sumption consumption rature spin Max rpm time (ap- wash wash load (number) (number) (approx. (approx. ° F cycle prox.min) litres) kWh) White Long... - Page 6 Service manual WM25 WM25.3 CIM-motor Machine pre-programmed for 3 rinses Pro- Water gram- Short Rinses con- Energy Pre- Main Final Max. Programme Temp°C spin (num- sumption (approx. time wash wash spin speed(rpm) load (number) ber) (approx. kWh) (ap- litres) prox.
-
Page 7: Indication Of Programme Sequence
Service manual WM25 Indication of programme sequence During the programme, the current programme sequence is indicated by a fixed light in the LEDs around the start/stop/ door open button (see the image). Start Final rinse Heating up Rinsing and spinning... - Page 8 Service manual WM25 Produces extra water in the main wash and rinses Cannot be selected for wool/ hand wash, spinning and draining Settings It is possible to select spin speed between 400 and 1400 rpm, CIM-motor between 400 och 1600 rpm, ”No spin” and ”No draining” (option depending on machine type).
-
Page 9: Variant Settings
Service manual WM25 Variant settings The variable settings below can only be made on a replacement card S = Push button L = LED Main power switch Total reset Hold the start/stop button (S1) in when you switch on the main power switch until an LED on the panel lights. -
Page 10: Test Programme
Service manual WM25 Test programme The entire test programme is run in a sequence as follows. You can cancel the test programme at any time during the programme by pressing the main power switch. S = Push button L = LED... - Page 11 Service manual WM25 Testing element, motor, thermistor, high level, for leakage, drain pump, spinning and door opening Press the start/stop button (S1). Indication of faults: • The element switches on. Fault indication/symp- Cause • The washing sequence starts. • The water is heated to 20°C.
-
Page 12: Fault Indications
Service manual WM25 Fault indications The following faults are indicated by a flashing red light in the start/stop/door opening button LEDs and as a trouble code on the display (not on all machine versions). Fault indication Cause Action Display L E D s ( f l a s - hing) Over filling. -
Page 13: Components And Measurement Values
Service manual WM25 Components and measurement values Item number Component Measurement value Comments 80 655 63 Motor 50 Hz Resistances: All resistance values have tolerances Pins 2-3 stator 1.41 Ω of ±8 %. Pins 1-3 stator 0.57 Ω Pins 4-5 rotor 1.54 Ω... - Page 14 Component Measurement value Comments 80 616 64 Pressure sensor 0.5 V out from the ASKO level sensor type 1166. Controls sensor (at 0 bar pres- intake and level sure and 230 V mains voltage, measurement carried out with the drain pump running...
-
Page 15: Technical Data
Service manual WM25 Technical data Height: 850 mm Width: 595 mm Depth: 585 mm Weight: 73 kg / 78 kg (with outer door) Cylinder volume: 50 l Max. washing capacity: 6.0 kg Spin speed max: 800/1400 rpm Spin speed max: CIM motor max... -
Page 16: Circuit Diagram
Service manual WM25 Circuit diagram CIM motor... - Page 17 Service manual WM25 Circuit diagram...
-
Page 18: Timer Diagram
Service manual WM25 Timer diagram... - Page 19 Service manual WM25 Timer diagram...
- Page 20 Service manual WM25 Timer diagram Servicemanual WM25 Timer diagram, table explanation Option Factory settings Action type Fill action fills up to the specified level Fills for selected time, if selected level is not reached within the time, continue to fill to selected level is reached Drain action, which pumps until specified level is reached + 30 seconds.
Need help?
Do you have a question about the WM25 and is the answer not in the manual?
Questions and answers