Front Panel Controls - Harman Kardon AVR4000RDS Service Manual

Front Panel Controls

30 29
•
• DIGITAL
• PRO LOGIC
• 3 STEREO
• 5CH STEREO
1
Power Phones
2
3 4
Main Power Switch
1
System Power Control
2
3 Power Indicator
Headphone Jack
4
5 Selector Buttons
Tone Mode
6
7 Surround Mode Selector
Tuning Selector
8
9 Tuner Band Selector
Preset Stations Selector
)
1 Main Power Switch: Press this button to
apply power to the AVR 4000. When the switch
is pressed in, the unit is placed in a Standby
mode, as indicated by the amber LED 3 sur-
rounding the System Power Control 2. This
button MUST be pressed in to operate the unit.
To turn the unit off completely and prevent the
use of the remote control, this switch should be
pressed until it pops out from the front panel
so that the word "OFF" may be read at the top
of the switch.
NOTE: This switch is normally left in the "ON"
position.
ˆ ıÙ
AVR 4000
• HALL 1
DTS MUTE
RDS PTY
• HALL 2
DOLBY D
• THEATER
PCM
MP3
• VMAx
OPTICAL 1 2 3 COAXIAL
• LOGIC 7
DIGITAL
• SURR. OFF
Test Tone
Tone Mode Surround Mode Tuning
¤ ⁄ ¤
5 6 7 8
Input Source Selector
!
@ RDS Select Button
# Digital Optical 3 Input
Digital Coax 3 Status Indicator
$
% Digital Coax 3 Jack
Video 4 input jacks
^
& Bass Control
Balance Control
*
( Treble Control
Volume Control
Ó
2 System Power Control: When the Main
Power Switch 1 is "ON, " press this button to
turn on the AVR 4000; press it again to turn the
unit off (to Standby). Note that the Power
Indicator surrounding the switch 3 will turn
green when the unit is on.
3 Power Indicator: This LED will be illumi-
nated in amber when the unit is in the Standby
mode to signal that the unit is ready to be
turned on. When the unit is in operation, the
indicator will turn green.
4 Headphone Jack: This jack may be used to
listen to the AVR 4000's output through a pair
of headphones. Be certain that the headphones
have a standard 6.3 mm stereo phone plug.
Note that the main room speakers and all
Preamp Outputs
off when the headphone jack is in use.
Ú
Û
O O
AUTO TUNED ST MEMORY PRESET
CT RT TA
L 0 C 0 R
SLEEP
O O
O O
LS LFE RS
1 2 3 ANALOG OSD O O
VMAx NF 5.1 LOGIC 7 CM
NIGHT MULTI
PRO LOGIC 3- STEREO 5 CH STEREO HALL 12 THEATER
Speaker Channel Digital Select Delay
Set
Band Preset Source
⁄ ¤ ⁄ ¤ ⁄
9 ) ! @
will automatically be turned
Ò  Ô
Volume
• VID 1 • CD
• VID 2 • TAPE
• VID 3 • FM
• VID 4 • AM
• DVD • 6 CH.
Bass Treble Balance
RDS
Min Max Min Max L
In – DIgital – In/Out Video 4
S-Video Video L – Audio – R
Optical 3 Coaxial 3
^
$
# %
Set Button
Ô
 Input Indicators
Ò Delay
Digital Input Selector
Ú
Û Main Information Display
Channel Select Button
Ù
ı Speaker Select Button
Test Tone Selector
ˆ
˜ Surround Mode Indicators
Remote Sensor Window
¯
5 Selector Buttons: When you are establish-
ing the AVR 4000's configuration settings, use
these buttons to select from the choices available,
as shown in the Main Information Display Û.
6 Tone Mode: Pressing this button enables or
disables the Balance, Bass and Treble tone con-
trols. When the button is pressed so that the
words TONE IN appear in the Main
Information Display Û, the settings of the
Bass & and Treble ( controls and of the
Balance control * will affect the output sig-
nals. When the button is pressed so that the
words TONE OUT appear in the Main
Information Display Û, the output signal
will be "flat, " without any balance, bass or treble
alteration.
FRONT PANEL CONTROLS 3
Ó
(
*
R
&