Table of Contents
Advertisement
Quick Links
CFI230J
Indigo Quadrant
Enclosure
with integrated
Mira Magna Shower System
(646)
Slide Rail
Fixed Head
Kohler Daryl Limited
Alfred Road, Wallasey, Wirral, CH44 7HY England
Fitting + User Instructions
Tel 44 (0)151 606 5000 Fax 44 (0)151 638 0303
www.daryl-showers.co.uk
E-mail Daryl@daryl-showers.co.uk
Advertisement
Table of Contents
Related Manuals for Kohler CFI230J
Summary of Contents for Kohler CFI230J
- Page 1 Indigo Quadrant Enclosure with integrated Mira Magna Shower System (646) Slide Rail Fixed Head Kohler Daryl Limited Alfred Road, Wallasey, Wirral, CH44 7HY England Fitting + User Instructions Tel 44 (0)151 606 5000 Fax 44 (0)151 638 0303 www.daryl-showers.co.uk E-mail Daryl@daryl-showers.co.uk...
-
Page 3: Safety Precautions
When the door is closed the edge of the seal should touch the side panel along it’s length. STEP CFI230J Fit top cap - Water delivery side The following pages aim to provide comprehensive installation instructions, plus advice on how to care and maintain your product. - Page 4 COMPONENTS Standard Top Caps Lintel Seal Side Panel Door Splashguard CFI230J Fixed Head Water Delivery Only Parking Block Nylon Grub Screw Blanking Support the weight of the column. Connect the water pipe to the connector from Caution Fixed Roller Support the weight of the column. Plug the...
- Page 5 Plug the electrical cable into the connector from the Water Delivery System at the top of the column. Caution STEP CFI230J Slide Rail Water Delivery Only Carefully lift the Water Delivery System column and place the bottom into the wall jamb...
-
Page 6: Enclosure Installation
Remove wall channel from jamb and place edge of the tray ‘A’. When jamb is vertical mark edge of wall channel on the wall ‘B’. ±0mm STEP CFI230J Fit roller securing caps to both top roller brackets. the tray ‘B’ STEP Cut the 2 metre pipe against mark on wall to size. - Page 7 Whilst supporting the weight of the door slide Lift the glass door up and slide the rollers onto the bottom roller into the bottom track Caution STEP CFI230J Check the wall channel is vertical and mark the roller and plastic glass guide Caution Seal behind channel STEP Slide glass panel into slot in tray “A’...
- Page 8 2mm lower than the top of the wall jamb. Tighten screws ‘A’ when the glass is in STEP CFI230J Check glass is vertical. If not Fit the fixed roller to the tray on the same side as remove screws, re-drill and lintel wall fixing, applying sealant on the edges.
- Page 9 When the lintel is level tighten screw ‘B’ on each panel clamp until it grips the glass. IMPORTANT - DO NOT OVER TIGHTEN Fit caps to lintel ‘C’ ± CFI230J 3. Drill holes with 6mm drill 4. Plug holes 7. Secure the lintel to parking block by tightening allen screw ‘A’...
- Page 10 Fit the splashguard to the bottom of the glass STEP CFI230J of the slot in the tray ‘B’. To adjust the glass it is the correct postion. Re-tighten screws Check end of...
-
Page 11: User Instructions
Coated surfaces are kept clean simply by rinsing or wiping with a damp cloth and regular use of Daryl Glass Cleaner. CFI230J USER INSTRUCTIONS Hint - these User Instruction pages can be separated from the Fitting Instruction pages if desired... -
Page 12: Customer Service
CUSTOMER SERVICE Kohler Daryl and Kohler Mira We take the question of customer service seriously. Consequently, there is one initial point of contact – Daryl Showering Technical Services (0151-606-5000). This team will ensure that the quality of support you require is provided by specialists appropriate to that field;... -
Page 13: Troubleshooting
Digital Mixer Valve malfunction Maximum temperature Incorrect shower temperature incorrectly set Digital Mixer Valve incorrectly fitted CFI230J Remedy Check water supply Check cable connections Check electrical supply Isolate product and turn back on after 30 seconds If the problem still... - Page 14 Option 2 - Locks the interface so no push-buttons can be used. Note! The Warm Up/Stop push-button will be illuminated on the interface used to set the lock mode, no other interface will be illuminated. CFI230J Temperature Selection °C Factory Set 45°C 45°C...
Need help?
Do you have a question about the CFI230J and is the answer not in the manual?
Questions and answers