Advertisement
Quick Links
Element 302 User Manual
1
Thank'you of purchasing this EamLab product. Who are dedicated to the
policy of creating the highest quality audio components, are proud to
introduce. You can be assured that in preparing this component, every
attention was paid in great detail by our entire staff to strict quality control .
This dedication was followed throughout the wole manufacturing process –
from basic research, the selection of each parts, assembly and testing – so
that we could supply a product with every confidence that it will give full
owner satisfaction and pride.
We welcome you to the fast-growning Eam Lab circle of dedicated audio
enthusiasts and true sound lovers
Advertisement
Related Manuals for eamlab Element 302
Summary of Contents for eamlab Element 302
- Page 1 Element 302 User Manual Thank’you of purchasing this EamLab product. Who are dedicated to the policy of creating the highest quality audio components, are proud to introduce. You can be assured that in preparing this component, every attention was paid in great detail by our entire staff to strict quality control .
- Page 2 Element 302 is a big power amplifier capable up 900 Wm rms for channel at 2 ohm impedance. Massive parallel output device combined with biggest and fast power supply guarantee a very high output driven current for difficult system speakers .
- Page 3 Contents 2 …………….Introduction & features 3 …………….Table of contents 4 …………….Safety instructions 5 …………….Unpackaging & preparation 6 …………….Function & protection 8 …………….Front pannel function 9 …………….Connections 10 …………….Troubleshooting guide 11 …………….Datasheet 12 …………….guarantee policy...
-
Page 4: Safety Information
WARNING: BEFORE YOU START TO USE READ AS FOLLOWS INFORMATION 5. The openings of the lid Safety information : provides adequate ventilation of the unit. In case of obstruction of 1. For best performance, please the same, the temperature inside read the rooms very quickly. - Page 5 EAMLAB to be overhauled or repaired. expeditions or long-term storage. Installation : Introduction : thanks to its ease of use, there are no first of all thank you for choosing our a...
-
Page 6: Function & Protection
Function and protection Ready to Power on After making connections 3- immediately disconnects the load in case correctly we are ready to turn on of failure of the transistors amplifier. 4 - disconnect the load in the event of a just made, amplifier... - Page 7 100 °. if the problem persists (LED always blinking) contact a service center The intervention THL will be signaled by EAMLAB. the fixed LEDs on the front panel (see fig.) Note : these LEDs will light when the heatsink it may happen sometimes, after the temperature reaches 70 °...
-
Page 8: Front Pannel Function
Front pannel function ILP : status led of protection or DC offset output Turn ON /OFF THL : status led of power amp Stand-by led temperature control... -
Page 9: Connections
Connection Input XLR and Switch single ended via input select : XLR or RCA Left and Right General switch : Powercord output to connect speaker : min. 2 and service ON/OFF fuse Front pannel back light : 1 : Trigger control. ON/OFF For turn ON/OFF amplifier with... - Page 10 troubleshooting problem Possible cause remedy No power on The plug on the power Securely connect the cord is not connected or plug or check the fuse on is not fully inserted . the rear panel next to The mains fuse is blown the socket No sound or sound very Connecting signal Input...
-
Page 11: Datasheet
datasheet Output power in Watt rms each 300 / 600 / 900 channel driven 20 hz to 20khz 8 / 4 / 2 ohm THD +N 0.03% full power at 8 ohm 1Khz Signal to noise ratio >105dB Damping factor 200 at 150 Hz 8 Ohm Input impedance 47 Kohm xlr / 25 Kohm RCA... -
Page 12: Return Authorization Procedure
MAIL : support@eamlab.com Website : www.eamlab.com How to return a product To return a product to EAMLAB, please follow this procedure so that we may serve you better: Obtain a Return Authorization Number (R/A number) and shipping address from the Krell Service Department.