1. Manuals
  2. Brands
  3. Alware Manuals
  4. Camera Accessories
  5. Lensman-X
  6. Instruction manual

Alware Lensman-X Instruction Manual

Camera 3-axis gimbal
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Lensman-X Camera 3-Axis Gimbal
Instruction Manual
V1.0
Page 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Lensman-X and is the answer not in the manual?

Questions and answers

Related Manuals for Alware Lensman-X

Summary of Contents for Alware Lensman-X

  • Page 1 Lensman-X Camera 3-Axis Gimbal Instruction Manual V1.0 Page 1...

  • Page 2: Table Of Contents

    Contents 1. Disclaimer & Warning......................3 2. Check List..........................4 3. Equipment Required For 360 Panning Operation..............6 4. Assembly Steps – Gimbal.......................7 5.0 Assembly Steps – Mounting onto Streak 800Pro..............10 5.1 Assembly Steps – Mounting onto DJI S800...............12 5.2 Assembly Steps – Carbon Battery Mount For DJI S800............14 5.3 Assembly Steps –...

  • Page 3: Disclaimer & Warning

    Due to unexpected changes or upgrades, the information contained in this manual is subject to change without notice. Please strictly follow the manual to assemble and use the Lensman-X Camera 3-Axis Gimbal. Since Alware has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury.

  • Page 4: Check List

    2. Check List Please Check the Follow parts. Tilt-Roll Assembly Pan Axis Assembly Boom Connection Assembly 1 Pcs 1 Pcs 1 Pcs Tripod Landing Gear Damping System (For Streak Damping System Screw Set Assembly 800Pro) 2 pcs (For Strek 800Pro) 4 Sets 3 pcs (Included with ALLENS- (Included with ALLENS-...

  • Page 5: Equipment Required For 360 Panning Operation

    3. Equipment Required For 360 Panning Operation 2-Axis Gimbal Stabilizer Transmitter (2CH or above) Receiver (2Ch or above) System 1 Pcs 1 Pcs 1 Pcs (e.g. ZYX-GS Gimbal Stabilization System) UBEC (Output 4.8-6V, 5A or 3S 11.1V Lipo Battery above, Input 12V or above ) (800mAh or above) 1 Pcs 1 Pcs...

  • Page 6: Assembly Steps - Gimbal

    4. Assembly Steps – Gimbal Step 1. Step 2. Loosen two M3x6mm Screw from the Pan Insert the Boom Connection Assembly into Axis Assembly for the installation of next the Pan Axis Assembly. step. Step 3. Step 4. Adjust the position of the Boom Connetion Secure the Boom Connection Assembly onto Assembly and secure with 2pcs M3x6mm the Pan Axis Assembly completely using...
  • Page 7 Step 7. Step 8. Insert the Tilt-Roll Assembly into the Boom Adjust the position of the Tilt-Roll- Connection Assembly. Assembly and seucre it with a M3x6mm Screw. (Apply little amount of Thread Locker when assembly metal to metal parts.) Step 9. Step 10.
  • Page 8 Step 13. Step 14. Secure the Tripod Landing Gear Assembly Repeat step 11-13 to install the other two using 2pcs M3x18mm Screws. (Apply little Tripod Landing Gear Assembly. amount of Thread Locker when assembly metal to metal parts.) Page 8...

  • Page 9: Assembly Steps - Mounting Onto Streak 800Pro

    Damping System. 3x5x20mm Collars. Step 5. Step 6. Repeat step 4 to install the other Damping Install the X-Mounting Frame of Lensman-X System onto Strealk 800Pro. Gimbal to the Damping System on the Streak 800Pro using M3x10mm Screws. (Apply little amount of Thread Locker when assembly metal to metal parts.)
  • Page 10 Step 7. Step 8. Close view of step 6. Lensman-X is now installed with Streak 800Pro. Page 10...

  • Page 11: Assembly Steps - Mounting Onto Dji S800

    5.1 Assembly Steps – Mounting onto DJI S800 Step 1. Step 2. Prepare the O-ring Damping System (For Prepare the DJI S800 H-Frame for DJI S800). installation. Step 3. Step 4. Insert the center rod of DJI S800 H-Frame Loosen the 12mm Metal Mount on O-ring into the center 12mm Metal Mount.
  • Page 12 Step 7. Step 8. Notice the mounting holes on the O-ring Notice the mounting holes on the X- Damping System which will be connected Mounting Frame which will be connected to X-Mounting Frame. the O-ring Damping System. Step 9. Step 10. Install the O-ring Damping System to the X- Close view of step 9.

  • Page 13: Assembly Steps - Carbon Battery Mount For Dji S800

    5.2 Assembly Steps – Carbon Battery Mount For DJI S800 Step 1. Step 2. Prepare the Carbon Fiber Battery Mount Remove 6pcs M2.5 screws from your DJI For DJI S800, 6pcs M2.5x18mm Screws and S800 Main frame as to install the Carbon 6pcs 9mm Nylon Collar.

  • Page 14: Assembly Steps - Mounting Onto Streak 1000

    5.3 Assembly Steps – Mounting onto Streak 1000 Step 1. Step 2. Prepare the O-ring Damping System (For Prepare your Streak 1000 Octocopter with Streak 1000). Landing Gear reomved. Step 3. Step 4. Disassembly the FPV & GPS Mount from Streak 1000 with FPV &...
  • Page 15 X-Mounting Frame. Step 11. Step 12. Notice the mounting holes on the X- Install the Lensman-X Gimbal to the O-ring Mounting Frame which will be connected Damping System which is mounted on the with the O-ring System. Streak 1000 using 8pcs M3x10mm Screws.
  • Page 16 Step 13. Step 14. Side view of Lensman-X Gimbal installed Install the FPV & GPS Mount back to Streak with Streak 1000. 1000 Main Frame. Step 15. Step 16. Close view of step 14. Complete installation of Lensman-X with Streak 1000.

  • Page 17: Assembly Steps - O-Ring Damping System

    5.4 Assembly Steps – O-Ring Damping System Step 1. Step 2. Part list of each O-ring Damping System. Default 4pcs O-ring have been used. It is able to support Camera with Appro. 1kg. You can adjust the number of O-ring used to suit your own camera.

  • Page 18: Electronic Installation

    6. Electronic Installation Step 1. Step 2. Prepare your own 2-Axis Gimbal Stabilizer. Stick the IMU sensor on the bottom of (We use ZYX-GS Gimbal Stabilizer as an Camera Mount Frame with double side foam example here.) tape. Please follow the installation direction of the IMU according to factory's instruction.

  • Page 19: Camera Cg Adjustment

    7. Camera CG Adjustment Step 1. Step 2. Remove 3pcs Screws from the Tilt Servo. Close view of step1. Step 3. Step 4. Rotate the Tilt Servo downward to disconnect Remove 3pcs Screws from the Roll Servo. the servo gear away from the main gear. So the Tilt Axis can be move freely now for the CG adjustment with your camera.
  • Page 20 ZYX-GS Gimbal Stabilizer Setting for Lensman-X Gimbal + Canon 60D (Appro. 1.2kg) (This is for reference only, you will need to adjust the Gain values to suit your own operation.) Page 20...
  • Page 21 Step 7. Step 8. 1/4 x 13mm Camera Screw on the Camera Install your Camera onto the Camera Stand Stand Frame is used to secure standard DSLR Frame using the 1/4x13mm Camera Screw. Cameras. Step 8. Step 9. Back view. Adjust the CG for Tilt Axis by adjusting the position of the camera on the Camera Stand Frame.
  • Page 22 Step 12. Step 13. Re-install the Tilt Servo back to original Ensure the Tilt Servo gear is fully contact position and secure with the M3 Screws and with Tilt Main gear without any gap between Nuts. the gears for stable operation. CG Adjustment Completed (Adjust the CG again once you have change the camera or lens for better and...

  • Page 23: Specifications

    8. Specifications - Made of 3K carbon fiber frames + 3K carbon boom + CNC anodized Aluminum metal parts - Pan axis control: ±360° continuous rotation (including the landing gear) - Tilt axis control: ±90° - Roll axis control: ±45° - Work with 3 Digital Metal Gear Standard Size Gimbal Servos - Working Voltage: 4.8-6V - Max.

  • Page 24: End Of Manual

    End of Manual Page 24...

Table of Contents