Related Manuals for Alware Lensman-Pro 3 Axis
Summary of Contents for Alware Lensman-Pro 3 Axis
- Page 1 Lensman-Pro 3 Axis DSLR Brushless Gimbal (For Handheld/ DJIS800/ 1000) Instruction Manual Updated Date: 22 Sept 2014...
-
Page 2: Table Of Contents
Table of Contents Check list..................................3 Equipment Required To Operate..........................4 STEP 1: Stand Assembly.............................5 STEP 2: Gimbal Assembly............................7 STEP 3: Gimbal Balancing – Pitch Axis........................9 STEP 5: Gimbal Balancing – Roll Axis........................12 STEP 6: Gimbal Balancing – Yaw Axis........................14 STEP 7: Power On and Controling..........................16 STEP 8: Converting to Aerial Mode..........................17 STEP 9: Gimbal Tuning Software..........................19 STEP 10: Firmware Upgrade.............................21... -
Page 3: Check List
Check list All the package should be packed and contain all the items as shown below. Please contact the vendor you purchased from if anything is missing at once. Alware Accessory Carry Bag and Stand Assembly Parts Main Body Assembly... -
Page 4: Equipment Required To Operate
Equipment Required To Operate DSLR Camera 3S 11.1V 2200mAh (or above) Lipo 3 Channel Radio and Receiver with XT-60 Connector (Optional) -
Page 5: Step 1: Stand Assembly
STEP 1: Stand Assembly Insert the Stand Lower Parts Around 265mm Secure the Stand Lower Parts by Tighten one Insert the Stand Upper Parts screw. - Page 6 Adjust the position to be Parallel. Secure the Stand Upper Part by Tighten one Complete Assembly of Stand Unit Screw...
-
Page 7: Step 2: Gimbal Assembly
STEP 2: Gimbal Assembly Put the Main Body Assembly as shown. Take off four Mounting Screws. Release the Upper Handle of the Handle Unit. Insert the Main Cable through the hole. Secure the Handle Unit to the Yaw Motor Plug the 5-wires Cable to the Joystick. with 4pcs Screws. - Page 8 Install back the Upper Handle. Put the Gimbal on the Stand. Release four Screws from the Battery Holder. Insert that four Screws to the frame as Secure the Battery Holder. Tighten your Battery to the Gimbal before Shown. move on to next step.
-
Page 9: Step 3: Gimbal Balancing - Pitch Axis
STEP 3: Gimbal Balancing – Pitch Axis Balancing the Center of Gravity (CG) for a Brushless Gimbal is extremely import. The more accurate the CG, the better the gimbal performance will be. Balancing require experience and time, so be patient. Before start Balancing the Gimbal, make sure Secure your Camera completely. - Page 10 Tighten these Screws. Holding the Side Fame of the Gimbal. Tilt the Camera in about 45 degrees. Camera should remain steady there when you release you hand when the CG is correct. Loosen total 8pcs Screws as to adjust the Up- Adjust the Camera (Up/ Down) and tighten Test the CG again in about 45 degrees.
- Page 11 Tighten all 8pcs Screws when the CG is well Make sure the Camera Plate is always set to Test the CG again with more angles. Camera tuned. be 90 degree (right angle). should remain steady in any angle if the CG is set correctly.
-
Page 12: Step 5: Gimbal Balancing - Roll Axis
STEP 5: Gimbal Balancing – Roll Axis Loosen these 2 Screws. (Hold the Camera at Adjust the Roll Assembly to Left/ Right as to Set it to be Parallel before tighten the Screws. the same time) balance the CG. Tighten these 2 Screws. Test if the Roll Axis is balanced well. - Page 13 Test again in another position. Test again in another position. Test again in another position.
-
Page 14: Step 6: Gimbal Balancing - Yaw Axis
STEP 6: Gimbal Balancing – Yaw Axis Rotate the Gimbal Main Assembly as to Tilt the Handle Unit to test if the Yaw Axis has Adjust the Gimbal in this direction if the CG is Parallel to the Handle Bar. correct CG. - Page 15 Set the Gimbal Main Assembly to be around If not, loosen these 2 screws and do the Adjust the CG by given a small rotation of the 45 degree. Tilt the Handle, the Camera adjustment. assembly. should remain steady if the CG is correct. Tighten the Screws and test again.
-
Page 16: Step 7: Power On And Controling
STEP 7: Power On and Controling Place the Gimbal on the Stand and set to this Connect the 3S 11.1V Battery to the Gimbal Gimbal is now controllable by the Joystick. recommended position. and wait around 3-5 seconds for the Operation Modes could be refer to: initialization. -
Page 17: Step 8: Converting To Aerial Mode
STEP 8: Converting to Aerial Mode Before Converting to Aerial Mode, main sure your Gimbal is entered in the Mode 4. When the Gimbal is powered on, Press 4 times of the Joystick as to enter to Mode 4. Now you can turn off the Gimbal and convert it to an Aerial Mode easily. Push the Joystick Release the Upper Handle. - Page 18 Connect the RC Control Cable to three Complete assembly in Aerial Mode. Installing on Cyclone X8/ DJI S800/ 1000 channels of your Receiver. multicopters. 3-wires Cable: Control Lock and Follow Mode (Connet to any 2-way or 3-way switch channel) Blue wire: Control Yaw movement Green wire: Control Pitch movement...
-
Page 19: Step 9: Gimbal Tuning Software
STEP 9: Gimbal Tuning Software Specification for the 32 bits SimpleBGC Camera Stabilizer System with [Lensman-Pro Gimbal]: Board: version 3.0 Firmware: v2.42 b7 (Can be upgraded via the GUI software easily!) Tuning Software: SimpleBGC GUI v2.42b7 Input Voltage: 11.1V 3S Lipo with XT-60 Connector (for the Default Setting) Default PID and Power Setting suitable for: DSLR Camera with Lens 0.8-1.4kg (Remarks: For other camera out of this range will need to have different PID setting.) How to connect to the computer? - Page 20 Step 3. Run the GUI Software (2_42b7): SimpleBGC_GUI_2_42b7 → SimpleBGC_GUI(.exe) Step 2. Select the correct COM, then click Step 1. Run the GUI.exe Software Step 3. If the Connection is successful, you Connect will see the current firmware. Before start tuning the gimbal, select the specific Profile (mean the Mode) and click “Write”...
-
Page 21: Step 10: Firmware Upgrade
STEP 10: Firmware Upgrade Step 3. Step 1 Step 2 Step 5. Step 4. You can Input your email (Optional) Step 6. Wait for Upgrading... - Page 22 Step 7. Wait for Upgrading Step 8. Step 9. Now you can see the updated Firmware of your Gimbal Controller. For more details, please refer to offical manual of the Gimbal Controller: SimpleBGC_32bit_manual_2_42_eng.pdf...
-
Page 23: End Of Manual
End of Manual...
Need help?
Do you have a question about the Lensman-Pro 3 Axis and is the answer not in the manual?
Questions and answers