Table of Contents
Advertisement
P/N 900129-00 REV. NC 01/2014
Ce manuel d'installation est disponible en
francais, s implement en faire la demande.
Numéro de la pièce 900186-00.
WARNING
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile
home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating
plate. This appliance is not convertible for use with other gases, unless a certified kit is used.
WARNING: If the information in these instructions is
not followed exactly, a fire or explosion may result
causing property damage, personal injury or death.
- Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire
department.
- Installation and service must be performed by a quali-
fied installer, service agency or the gas supplier.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
INSTALLATEUR: Laissez cette notice avec l'appareil.
CONSOMMATEUR: Conservez cette notice pour consul-
tation ultérieure.
Direct-Vent
SEREFINA™ SERIES
Portland
US
OTL Report No. 116-S-08-5
P900129-00
AVERTISSEMENT
INSTALLATION AND OPERATION
MODELS
CI1500DVF
UNE SURFACE VITRÉE CHAUDE PEUT
CAUSER DES BRÛLURES.
LAISSER REFROIDIR LA SURFACE
VITRÉE AVANT D'Y TOUCHER.
NE PERMETTEZ JAMAIS À UN ENFANT
DE TOUCHER LA SURFACE VITRÉE.
AVERTISSEMENT : Assurez-vous de bien suivre les
instructions données dans cette notice pour réduire
au minimum le risque d'incindie ou d'explosion ou
pour éviter tout dommage matériel, toute blessure
ou la mort.
- Ne pas entreposer ni utilizer d'essence ni d'autres
vapeurs ou liquides inflammables dans le voisinage
de cet appareil ou de tout autre appareil.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucan interrupteur. Ne pas vous servir
des téléphones se trouvant dans le bâtiment où vous
trouvez.
• Appelez immédiatement votre fournisseur de gaz
depuis un voisin. Suivez les instructions du fournis-
seur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service des incindies.
- L'installation et l'entretien doivent être assurés par un
installateur ou un service d'entretien qualifié ou par
le fournisseur de gaz.
CI2500DVF
Advertisement
Table of Contents
Related Manuals for IronStrike CI1500DVF
Summary of Contents for IronStrike CI1500DVF
-
Page 1: Installation And Operation
Direct-Vent SEREFINA™ SERIES Portland P/N 900129-00 REV. NC 01/2014 MODELS OTL Report No. 116-S-08-5 Ce manuel d’installation est disponible en CI1500DVF CI2500DVF francais, s implement en faire la demande. Numéro de la pièce 900186-00. P900129-00 WARNING AVERTISSEMENT HOT GLASS WILL UNE SURFACE VITRÉE CHAUDE PEUT... -
Page 2: Table Of Contents
CONGRATULATIONS! Step 4 Remove Front Glass ........15 Step 5 Remove Firebox Contents ......15 When you purchased your new gas stove, you joined the ranks Step 6 Remove Cardboard Packaging ....15 of thousands of individuals whose answer to their home heat- Step 7 Install LP Conversion / Options ....15 ing needs reflects their concern for aesthetics, efficiency and Step 8 Install Lower Access Door ......16... -
Page 3: Safety And Warning Information
IMPORTANT SAFETY AND WARNING AVERTISSEMENT INFORMATION On ne devrait pas placer de vêtements ni d’autres matières inflammables sur l’appareil ni à proximité. WARNING WARNING Young children should be carefully supervised when they are in the same room as the appliance. Tod- Any safety screen or guard removed for servicing dlers, young children and others may be susceptible the appliance must be replaced prior to operating... - Page 4 T hese appliances are vented gas appliances. Do not burn wood F OR YOUR SAFETY do not install or operate this appliance without or other material in these appliances. first reading and understanding this manual. Any installation or operation of the appliance deviating from that which is stated T his appliance is only for use with the type of gas indicated on in this manual WILL void the warranty and may be hazardous.
-
Page 5: Homeowner - Attaching Safety In Operation Warnings
Cat. No. H8024 Replacement Label Kit recevoir gratuitement des étiquettes supplémentaires. Juego de etiquetas de repuesto - Nº de cat. H8024 Étiquettes de remplacement, n° cat. H8024 www.IronStrike.us.com www.IronStrike.us.com www.IronStrike.us.com NOTE: English is red text on clear label. French Nota: La etiqueta en inglés es transparente con texto and Spanish are white text on black label. -
Page 6: General Information
Provide adequate clearances around air openings and adequate acces- Model Natural Propane Elevation sibility clearance for service and proper operation. Never obstruct the Feet (meters) front openings of the appliance. CI1500DVF #37 (.104") 1.55mm (.061") 0-4500 (0-1372) CI2500DVF .121" 1.75mm (.068") 0-4500 (0-1372) These appliances are designed to operate on natural or propane gas only. -
Page 7: Introduction
WARNING: This appliance must be properly connected to a venting INTRODUCTION system. Operation of this gas appliance when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. The stove models covered in this manual are Direct-Vent sealed combustion vented gas stove heaters designed for residential and Carbon Monoxide Poisoning: Early signs of carbon monoxide manufactured home applications. -
Page 8: Orifice Size/Altitude Adjustment
ORIFICE SIZE/ALTITUDE ADJUSTMENT CODES AND APPROVALS Certification For altitudes above 4,500 FT (1370 M), the orifice should be de-rated by 4% for every 1,000 feet to maintain the proper ratio of gas to air. Improper Gas appliances must be tested and certified by a nationally recognized orifice sizing may result in damage and unsafe conditions. -
Page 9: Pre-Installation
• Blower Kit • Firebox Liner Kits • Warming Shelves * Other approved chimney brand is Simpson Dura-Vent DV-GS. • Firescreen Kits CI1500DVF CI2500DVF RATINGS NATURAL GAS LP GAS NATURAL GAS LP GAS... -
Page 10: Specifications / Dimensions
SPECIFICATIONS: Serefina™ Dimensions CI1500DVF CI2500DVF 24-1/2” (622 mm) 30-1/2” (775 mm) 27-1/2” (699 mm) 28-1/2” (724 mm) 19” (483 mm) 22” (559 mm) 7” (178 mm) 7” (178 mm) 20-1/2” (521 mm) 23-1/2” (597 mm) (with ashlip) 6” (152 mm) 6”... -
Page 11: Clearances To Combustibles
* Dimensions with a single asterix are reference dimensions only. ** If the optional warming shelves are installed, a greater alcove width is required as follows: CI1500DVF - 44" (1118 mm) min. CI2500DVF - 52-1/2" (1334 mm) min. Figure 2B ***This includes any projections such as shelves, windowsills, mantels, etc. -
Page 12: Manufactured (Mobile) Home Requirements
MANUFACTURED (MOBILE) HOME REQUIREMENTS TERMINATION HEIGHTS FOR VENTS ABOVE FLAT OR SLOPED ROOFS Horizontal Overhang These models may be installed in an aftermarket permanently located, manufactured home, where not prohibited by local codes. 2 FT Vertical MIN. 2 FT MIN. Wall When installed in Manufactured Housing the following supplemental Lowest... -
Page 13: Installation
Exterior Horizontal Vent Termination Clearance Requirements * See Item D in the Text Below. Center Line Exterior Wall Inside of Termination Corner Detail *18” Horizontal Termination 18” Ventilated Soffit Inside Corner = 9" in U.S. = 12" in Canada DETAIL D 3 ft. -
Page 14: Typical Installation Sequence
The gas supply line should be plumbed from the fuel source to the WARNING area where the appliance is to be installed per requirements outlined in NFPA 54 - latest edition (USA) and CAN/CGA-B149.1 - latest edi- Failure to position the parts in accordance with these tion (Canada). -
Page 15: Step 4 Remove Front Glass
NOTE: Install Leg Leveling Bolts if Necessary: The four leg leveling CAUTION: Label all wires prior to disconnection when servic- bolts (included in literature package), are provided for leveling the stove ing controls. Wiring errors can cause improper and dangerous if necessary. -
Page 16: Step 8 Install Lower Access Door
Wiring - Optional Forced Air Blower Kit: Step 8: INSTALL LOWER ACCESS DOOR BK-CI (see Figure 8 for wiring diagram) - (An optional field-provided Install the lower access door by inserting the tabs on the door sides outletbox/J-Box may also be used). Install the blower kit according to into the corresponding holes on the brackets on the stove bottom the installation instructions provided with the kit. - Page 17 Horizontal Termination Vertical Termination The vent must rise vertically, a minimum of 24" (610 mm) off the A vertical vent system must terminate no less than 8 feet ( 2.44 meters) top of the appliance for Natural Gas and 36" for Propane Gas before and no more than 40 feet / 12 meters (above the appliance flue collar).
- Page 18 The chimney conversion should not be applied to the portion of the vent Installing Support Brackets system that is in the room of the appliance. Use only Co-Axial direct- vent pipe (4” inner pipe, 6 5/8” outer pipe as listed on Page 19) from the Install support brackets per vent manufacturers instructions.
- Page 19 DIRECT-VENT SYSTEM COMPONENTS The following "Secure Vent " or "Simpson Dura-Vent" brand Direct-Vent components may be safely used with these appliances. ® IMPORTANT NOTE: Seal the first section of pipe to the stove collar using mill-pac black, high temperature sealant. Model # SECURE VENT - Description Model #...
-
Page 20: Step 10 Connect Gas Line
When first lighting the appliance, it will take a few minutes for the line Step 10. CONNECTING GAS LINE to purge air from the appliance. Once purging is complete, the pilot and burner will light and operate as indicated in the instruction manual. Subsequent lightings of the appliance will not require such purging. - Page 21 5. Install the right front log onto the corresponding burner pin and NOTE: If an optional Brick Liner Kit was purchased, install it now, per instruc- tions provided in kit sub-floor right tab as shown in Figure 21. 2. Place the largest log onto the rear log stoppers (see Figure 17). Ensure that the grooves on the bottom of the log aligns onto the corresponding places on the rear log stoppers.
-
Page 22: Step 12 Reinstall Front Glass
8. Install the front right twig onto the corresponding pin on the right front log. Align the twig with the indentation on the front right log as shown in Figure 24. Right Front Twig DO NOT PLACE EMBERS ON TOP OF THE BURNER SLOTS. Figure 26 VERIFYTHATTHEGASLINEHASBEENPURGEDOFAIR(SEESTEP10). -
Page 23: Step 14 Check Appliance Operation
Step 15. BURNER ADJUSTMENTS Step 14. CHECKING APPLIANCE OPERATION With gas line installed run initial system checkout before closing up Flame Appearance and Sooting the front of the unit. Follow the pilot lighting instructions on Page 30 (or pull out the instruction label located in a holder on rear shield Proper flame appearance is a matter of taste. -
Page 24: Step 16 Install Top, Trivet & Ash Lip
Align the ash lip below the firebox as shown in Figure 33 (the tapped holes in ash lip should align with 5/16" 5/8" CI1500DVF corresponding slots below firebox). Reinstall the 2 bolts that were (7.93 mm) (15.9 mm) removed from the ash lip (finger tight only. -
Page 25: Operation And Care Of Your Appliance
OPERATION AND CARE OF YOUR APPLIANCE HI / LO Knob Inlet Variable Flame Height Adjustment Pressure Appliance operation may be controlled through a remotely located optional Port Manifold Pressure Port wall thermostat or remote control. In lieu of remote or remote wall thermostat operation, the appliance must be operated directly through the on/off rocker switch located on the upper right side of the rear shield. -
Page 26: Front Glass Enclosure Panel
B. Reach under the bottom front of the front glass enclosure and pull FRONT GLASS ENCLOSURE PANEL, REMOVAL AND INSTAL- it forward as shown in Figure 38. LATION WARNING • Do not attempt to substitute the materials used on these doors, or replace cracked or broken glass. •... -
Page 27: Maintenance
MAINTENANCE WARNING Do not use abrasive cleaners. Never clean the glass WARNING when it is hot. Turn off gas and electrical power to the fireplace and allow it to cool before cleaning or servicing WARNING the appliance. Do not attempt to touch the front enclosure glass with your hands while the stove is in use. -
Page 28: Wiring Diagrams
WIRING DIAGRAMS OPTIONAL ROOM AIR BLOWER IMPORTANT: Ground supply wire must be connected to the green Wiring diagrams are provided here for reference purposes only. This wire attached to the green ground screw. Failure to do so will information is also provided on schematics attached directly to the appli- result in a potential safety hazard. -
Page 29: For Your Safety Read Before Lighting
LIGHTING INSTRUCTIONS – SIT MILLIVOLT GAS VALVE FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. • Immediately call your gas supplier from a neighbor’s phone. A. - Page 30 INSTRUCTIONS D’ALLUMAGE - VANNE GAZ MILLIVOLT SIT POUR PLUS DE SéCURITé, LIRE AVANT D’ALLUMER AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice risque de déclencher un incendie ou une explosion entraînant des dommages, des blessures ou la mort. •...
-
Page 31: Rating Labels
PROFONDEUR D'ALCÔVE MAXIMALE 1219.2mm 6/24/03 T-2185: MODEL WAS CI1500DVF DIRECT VENT GAS STOVE / APPAREIL A GAZ AVEC EVACUATION DIRECTE DIRECT VENT GAS STOVE / APPAREIL A GAZ AVEC EVACUATION DIRECTE VENTED GAS STOVE HEATER – NOT FOR USE WITH SOLID FUEL. -
Page 32: Maintenance Schedule
MAINTENANCE SCHEDULE Annually (Before the onset of the Burning Season) Maintenance Task Accomplishing Person Procedure Inspecting/Cleaning Burner, Logs Qualified Service Technician Inspect valve and ensure it is properly operating. Check piping for and Controls leaks. Vacuum the control compartment, fireplace logs and burner area. -
Page 33: Troubleshooting
TROUBLESHOOTING THE Millivolt GAS CONTROL SYSTEM NOTE: Before troubleshooting the gas control system, be sure external gas shut off valve (located at gas supply inlet) is in the “ON” position. Important: Valve system troubleshooting should only be accomplished by a qualified service technician. SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION... -
Page 34: Replacement Parts List
Item Cat. No. Description Where Used Contact an IHP dealer to obtain any of these parts. H3703 Glass Panel Enclosure Assem- CI1500DVF Series bly, Complete WARNING H3704 Glass Panel Enclosure Assem- CI2500DVF Series bly, Complete Never use substitute materials. Use of non-approved Knob, Rheostat, 1 ea. - Page 35 Trivet, Enamel Mid. Blue, 1 ea. CI2502DVF 1 ea. 55M98 Trivet, Painted Black, 1 ea. CI1500DVF 66M08 Leg Casting, Painted Black, CI1500DVF & CI2500DVF 66M19 Trivet, Painted Black, 1 ea. CI2500DVF 1 ea. Room Air Blower System (Optional Kit) H1007 Side Casting, Left - Enamel CI1506DVF Hunter Green, 1 ea.
- Page 36 REPLACEMENT PARTS DIAGRAMS Front View Log Set Does Not Include Ember Strip (purchased separately) Front View NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
-
Page 37: Accessories
ACCESSORY COMPONENTS Cost Effective Solution • Simple On/Off operation • Works with millivolt and low voltage electronic ignition controls Flame and Heat modulation Kit includes: • Includes solenoid for SIT millivolt valves Remote and Receiver • Thermostatic, manual or up to 9 hour Count- Thermostatic or Manual modes down Timer modes G-Fire Remote, Simple On/Off... - Page 38 Cat. No. Model Description disc. H0773 BLK-CI15 Brick Liner Kit CI1500DVF Series H0774 BLK-CI25 Brick Liner Kit CI2500DVF Series (ref. form # 775151M) Blower Warming Shelves These attractive warming shelves are designed to be functional for placing food to stay warm.
- Page 39 Model Description Where Used 55M63 Paint, Touch-up for enamel, 1/2 oz - Ivory White, 1 ea. H0768 FSF-CI15 Flat Screen CI1500DVF 55M61 Paint, Touch-up for enamel, 1/2 oz - Maj. Brown, 1 ea. H0770 FSF-CI25 Flat Screen CI2500DVF 55M60 Paint, Touch-up for enamel, 1/2 oz - Mid. Blue, 1 ea.
-
Page 40: Warming Shelves - Installation Instructions
4. Place the insets (4 ea. for the CI1500 series or 6 ea. for the CI2500 OPTIONAL WARMING SHELVES KIT series) into the recessed areas on both warming shelves as shown in Figures 44 and 45. NOTE: Common ceramic tiles (4-1/4” square) can Kit Contents: be used in place of insets on the warming shelves (available at most 2 ea. -
Page 41: Warranty
THE WARRANTY Innovative Hearth Products ("IHP") 20 Year Limited Warranty warrants your IronStrike™ brand gas fireplace or insert ("Product") to be free from defects in materials and workmanship at the time of manufacture. The Product body and firebox carry the 20 Year Limited Warranty. Ceramic glass carries the 20 Year Limited Warranty against thermal breakage only. -
Page 42: Product Reference Information
See Page 34 for a complete replacement parts list. Use only parts sup- 1508 Elm Hill Pike, Suite 108 plied from the manufacturer. Nashville, TN 37210 visit us at www.IronStrike.us.com Model Number _____________________________________________________ Serial Number _____________________________________________________ Date Installed ______________________________________________________ Your Dealer's Name _________________________________________________...
Need help?
Do you have a question about the CI1500DVF and is the answer not in the manual?
Questions and answers