Cupboard Dimensions - Electrolux STM3900 Installation Manual

CuPBoaRd dIMEnSIonS

IMPORTANT!
Pages 5, 6, 7 and 8 should be given to the person
responsible for cupboard design and construction.
The cupboard dimensions required for each model are
shown on page 6, 7 & 8.
1. all sizes are internal and measured in millimetres.
2. It is important to ensure that the correct cupboard
sizes are used to ensure adequate air flow around
the refrigerator.
3. Cupboard hinges should be a 120° opening type.
(use hinges supplied).
4. Three hinges should be used on each cupboard
door higher than 1000mm.
5. Ensure the refrigerator is not connected to a power
supply whilst installation takes place.
6. Each operation should be carried out in the sequence
specified in this instruction sheet.
NOTE: All sizes are internal and in millimetres.
Model
2 door top freezer models
WTB2300
WTB2500
WTB2800
WTM2800, KTM2800
WTM3000, KTM3000
WTM3300, KTM3300
WTB3400
KTM3600
WTB3700
WTM3900, KTM3900, STM3900
WTM4200, WTE4200, KTM4200, STM4200
WTM4400, KTM4400
WTM5200, WTE5200, KTM5200
2 door bottom freezer models
WBM3700
WBM3800, KBM3800, SBM3800
WBM4000
WBM4300, WBE4300, KBM4300, SBM4300
WBM5100, WBE5100, KBM5100
single door models
WFM3000
WFM3600
WRM3700
WRM4300
Step 1
Measure and confirm dimension 'a'.
Step 2
To calculate dimension 'I' use the equation below.
Dim 'I' = Dim 'A' - (Dim 'D' + 5mm) mm
Dim 'A' Dim 'B' Dim 'C'
(mm) (mm) (mm)
minimum
1485 680 645
1550 680 645
1650 680 645
1640 680 700
1710 680 700
1810 680 700
1690 715 700
1730 680 795
1800 715 700
1810 680 795
1730 740 795
1810 740 795
1810 740 895
1660 740 745
1810 680 795
1760 740 745
1810 740 795
1810 740 895
1810 680 700
1810 680 795
1810 680 700
1810 680 795
Step 3
Dim 'D'* Dim 'E' Dim 'G'
(mm) (mm)
910 450
975 450
1075 450
1047 500
1117 500
1217 500
1110 500
1137 600
1220 500
1217 600
1137 600
1217 600
1217 600
702 600
702 600
702 600
702 600
702 600
– 500
– 600
– 500
– 600
* add cabinetry thickness to dimension 'd' and
dimension 'I' for final measurement before construction.
Dim 'H' Dim 'I' *
(mm) (mm) (mm)
270 250
270 250
270 250
219 300
219 300
219 300
298 300
241 395
298 300
Please
241 395
use the
241 395
calculation
241 395
below to
278 495
measure
Dimension
'I' for your
specific
241 395
model.
241 395
241 395
278 395
495
219 300
241 395
219 300
241 395
5