Page 1
SEC-DVRMON20 4CH DVR MONITOR Short description guide of the DVR monitor. For full details of using the DVR monitor, refer to advanced manual ANLEITUNG MANUAL MODE D’EMPLOI GEBRUIKSAANWIJZING MANUALE MANUAL DE USO HASZNÁLATI ÚTMUTATÓ KÄYTTÖOHJE NÁVOD K POUŽITÍ BRUKSANVISNING...
Page 2
Description top panel: MENU/POWER: A) Long press: turn on or turn off the LCD monitor (Stand-by mode) B) Short press: used for menu of the monitor (not DVR) / move the cursor left or right. Select the parameters of the sub menu upwards. DOWN: Select the parameters of the sub menu downwards Increase the volume or increase the value of the parameter in the sub...
“SLEEP”: 0~240 minutes. The value is increased or decreased by ten. The value of “sleep” indicates how long the LCD monitor will be turned off automatically if “OFF-TIME” is not set. Second, sets for closedown time and time of starting the LCD monitor, the screen closes and reveals at corresponding time point.
Page 4
7. RECORD (REC) To start manual recording. To stop recording, press REC button again. 8. HDD (Hard Disk Drive) LED (RED) System is recording or in playback mode. 9. POWER (PWR, GREEN) System power is ON. 10. IR EYE Receiver for remote control signal. 11.
Page 5
1. DC POWER INPUT Use only supplied AC/DC power supply. 2. AUDIO OUTPUT Audio for playback. 3. MAIN POWER SWITCH Switch ON or OFF the DVR system. 4. VIDEO OUT Video output signal for another monitor. 5. AUDIO INPUT (1&2) Audio input for microphone connection.
Page 6
Description remote control: 1.CH1↑ Select CH1 or move cursor up 2.CH2↓ Select CH2 or move cursor down 3.CH3← Select CH3 or reduce value 4.CH4→ Select or increase value 5.QUAD Quad view 6.◄◄ (Z-) Rewind or zoom- 7.► (F+) Play record list or focus+ Forward or zoom+...
GETTING STARTED Install a hard disk drive into your DVR. Connect cameras (up to 4) to DVR. Connect other peripheral devices (mouse, external motion sensors or alarm) if necessary. And PS/2 Mouse must be connected to DVR before startup system. Plug the power cord into the power jack on the wall.
SATA Hard Drive Installation Connect the cables as follows. Monitor Connection To display video image from cameras on the monitor, the DVR’s video output signal should be transferred to your TV set or monitor. Connect a monitor with “VIDEO OUT” ports on DVR “VIDEO IN”...
Sensor Connection Our 4 CH DVR system can connect up to four sensors. There are two steps for sensor installation. (a) Connect the sensor signal lines to the signal input terminal. (b) Connect the sensor power lines to the appropriate power source. In general, there are three different types of sensors available in the home electrics store, where you can buy them.
Mouse Connection Connect PS/2 mouse with the port below on the system. And PS/2 Mouse must be connected to DVR before startup system. DVR Power Connection Connect a DVR power adapter to the adapter jack at the rear panel of DVR unit. And turn the power switch on.
Page 11
The system allows up to four user accounts. The administrator can set up the login name, password and level for each user. (Please refer to Section 5.6.2 for Account Setup.) The admin can operate everything. The operator can operate anything except examining user accounts, formatting HDD and modifying his password level.
Page 12
Logout The DVR Front Panel or Remote Control Press the “UP” or “DOWN” key on the DVR front panel or remote control to move the cursor. Press “SELECT” button on the front panel or remote control in order to change the settings. In the MAIN MENU, the cursor “...
Page 13
A: [RECORD FRAMERATE] Change the record frame rate for each channel. The higher the record frame rate, the more natural movement you will see while playback. Independent each channel frame rate adjustment is possible. System default value is 12 frames per second with each channel, which means the system will record 48 frames per second with all channels.
Page 14
- Grey bar: No record will be made for this time period if user can’t activate manual recording. - Red bar: The time period with a red bar will activate continuous recording mode (Time record) unless there is any manual stopping during recording during that time. - Green bar: The time period with a green bar for built-in motion recording (MD).
D: [SENSOR] Activate / deactivate or choose the type of sensor. There are three different modes for sensor setting: N.C (NORMAL-CLOSE) & N.O (NORMAL-OPEN) & NONE. Select “None” to deactivate sensor recording or if there was no sensor installed in DVR system. Chose the type of sensor (N.O or N.C) installed in DVR.
right. Mouse function: Hold a right mouse click button, there will be some icons on the screen as follows “ ”. Hold a left mouse click button to click each icon to select. -“▲for up, ▼ for down, ◄ for left, ► for right, “ ”...
HARD DISK SETUP [OVERWRITE ENABLED] If you choose Yes, recording continues and overwrites previous recording when hard disk drive space is full. If you choose No, the recording stops when the hard disk drive is full. It won’t record until “overwrite enable” is “Yes”.
ACCOUNT SETUP Only user log in the system at Admin level, the Account Setup allows the administrator to add new users, delete existing ones, and modify the user’s name/password/level. The system allows up to 4 user accounts. [Account]/[Password] In setup Menu display, move the cursor to change the highlighted option to Account, and then press [SEL] to call up Account/Password as shown.
PASSWORD SETUP The default password is 111111. All numbers, letters and sign in the pane can be used as password. Press 「SEL」to input value, and move the prompt to the option of “Enter”, press 「SEL」to input current password. — CH1 for up, CH2 for down, CH3 for left, CH4 for right.
To move the cursor on the screen, use “UP” and “DOWN” key on the DVR front panel or remote control and then press “SELECT” button to change the numeric value. Once you finish time setting, press “MENU” button. Then press “DOWN” key and “SELECT” button to apply the new time set.
Page 21
Button function On the Front Panel or Remote Control: 「Select」:Make sure the setting. 「Up」「Down」:Move the cursor. 「REC」: Auto scan. 「Ch1」「Ch2」: Move the dome upwards and downwards. 「Ch3」: Move the dome leftwards or Reduce Value 「Ch4」: Move the dome rightwards or Increase Value. 「STOP」:Stop the dome running.
Page 22
Attention: User can start-up automatic scout in “PTZ SETUP” menu or PTZ mode. It doesn’t stop when user exits. If user wants to stop scouting, press 「STOP」button in PTZ mode. During live view, user can press「PTZ」button to enter PTZ mode, and then user can operate to control the dome according to the method of above paragraphs.
PLAYBACK WITH TIME SEARCH FUNCTION This is an enhanced playback option, which enables the user manually to adjust a specific starting time for playback. [Keypad Control]: In order to playback with time search function, press "PLAY” button on front panel or remote control first. And then press “SELECT”...
It will take a few minutes to write the video data on USB memory stick. The file size number is going up until it’s done with the message below. WRITING… Then it will show the following message on the screen. FIXATING…...
PLAYBACK WITH BACK-UP VIDEO DATA ON PC Install 1). Put the Driver Program CD in your CD-ROM. 2). Go for installing by setup. 3). Set up the install directory. 4). Execute: Start >Program >VxViewer >Vx4SLPlayer. Program Interface Double click icon “ ”...
Page 26
Button Function 1. Open File 2. Fast Backward 3. Play Reverse 4. Previous Frame 5. Pause 6. Next Frame 7. Play 8. Fast forward 9. Still Capture 10. Split 1 11. Split 4 12. Volume Scroll Bar 13. Mute On/Off 14.
Page 27
2) Still Capture Click “ ” to still capture. Click the right mouse button to select “Options…” to setup path for still capture. Click the left mouse button to select folder that you want to, for example select the folder as “E:\VOC 4CH\backup”. 3) In “Options”...
Page 28
5) Translate “VVF File Format (*.VVF)” into “AVI File Format (*.AVI)”. According to the below figures, first click the right mouse button to select the option “Export”, and then click the left mouse button you will see the window “Export To AVI”. Secondly select channels you want to export, you can choose the audio to export whether or not.
Page 29
7) Open Disk… User can playback the record data in the HDD directly through the client software. User can install the HDD to PC directly. Click the option “Open Disk…”, and there will be a dialog of “Disk Select”. Select the HDD including video data to play.
SPECIFICATION ITEM DESCRIPTION Video Format NTSC / PAL Operation System Linux Camera Input Channel 4 channel Composite BNC Video Output Channel 1 channel Composite BNC Max 60 fps (Total) NTSC Recording Frame Max. 30 frames/s (Each Channel) Rate Max.50 fps (Total) Max.
Page 31
APPENDIX System Connect Sketch Map Fitting Come Along With DVR 1. Power Adapter 1pcs 2. Power Cord 1pcs 3. Remote Control (Optional) 1pcs 4. User Manual 1pcs 5. USB Drive CD 1pcs 6. Mouse (Optional) 1pcs 7. Batteries of Remote Control 1pcs...
Page 32
Used the compatible USB Stick. In case the noise occurs on USB line due to a variety of reasons such as power noise, it might cause the error while data transferring process. In this case, it requires re-transfer the date on memory stick.
Safety precautions: Do not expose the product to water or moisture. Maintenance: Clean only with a dry cloth. Do not use cleaning solvents or abrasives. Warranty: No guarantee or liability can be accepted for any changes and modifications of the product or damage caused due to incorrect use of this product.