Advertisement
Quick Links
SECURITY SYSTEM NOTES
Installing/Service Company
For Service Call
1
"Chime" Digit
ENTRY / EXIT DELAY TIMES
Exit Delay Time
Entry Delay Time
Partial Arm Warning Time
Master Code/User #
01
04
05
08
09
12
13
1
3
SPECIAL CODES
2
"Partial Arm" Digit
Secondary Exit Delay Time
Secondary Entry Delay Time
ARM / DISARM CODES
02
06
10
14
ZONE DESCRIPTIONS
2
4
1
3
"Quick Arm" Digit
03
07
11
15
Advertisement
Related Manuals for DAS DL100
Summary of Contents for DAS DL100
- Page 1 SECURITY SYSTEM NOTES Installing/Service Company For Service Call SPECIAL CODES "Chime" Digit "Partial Arm" Digit "Quick Arm" Digit ENTRY / EXIT DELAY TIMES Exit Delay Time Secondary Exit Delay Time Entry Delay Time Secondary Entry Delay Time Partial Arm Warning Time ARM / DISARM CODES Master Code/User # ZONE DESCRIPTIONS...
- Page 2 THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION. ALL USERS OF YOUR SECURITY SYSTEM SHOULD READ AND FOLLOW THE INSTRUCTIONS AND PRECAUTIONS IN THIS BOOKLET. FAILURE TO DO SO COULD RESULT IN THE SECURITY SYSTEM NOT WORKING PROPERLY.
- Page 3 PLEASE READ THIS ENTIRE BOOKLET CAREFULLY BEFORE OPERATING YOUR SECURITY CONTROL SYSTEM. IF YOU DO NOT UNDERSTAND ANY PORTION OF THIS MANUAL, OR IF YOU HAVE ANY QUESTIONS ABOUT YOUR SYSTEM, CONTACT THE INSTALLING COMPANY LISTED ON PAGE 1 OF THIS BOOKLET.
-
Page 4: Alarm Memory
HOW TO ARM YOUR SECURITY SYSTEM To Arm the security system, close all of the protected doors and windows. The green "READY" light on the code pad control will be illuminated when all of the protected zones and sensors are secure. -
Page 5: Automatic Arming Option
programmed. This feature will allow you to arm the security system by pressing one, pre- designated key on the code pad control. This "QUICK ARM" code is for ARMING ONLY, and will not disarm the security system. This makes it ideal for a maid code, babysitter code, etc. This code can only be programmed and/or changed by your installing company. -
Page 6: Duress Code
TURNING ON THE CHIME FEATURE If this box is checked, your security system will operate in the "CHIME" mode, allowing the monitoring of pre-designated zones while the security system is not armed. While in the "CHIME" mode, the opening of any of these zones will produce a tone from the code pad control. - Page 7 immediate, or delayed audible notification by sounding the siren and/or code pad sounder. Check with the installing company listed on page 1 to find out if notification will be delayed or immediate, and what kind of sound will be created in case of a telephone line fault.
- Page 8 (Master Code) USER PROGRAMMABLE TELEPHONE NUMBERS When pager or siren tone formats are selected, any of the DL100's three phone numbers may be programmed or altered in the run mode. The process would consist of entering the phone number via the LED or LCD code pads with a read back facility only on the LED code pad.
- Page 9 REVIEWING PHONE NUMBERS IN THE RUN MODE Once the [#] is pressed to mark the end of the phone number, the DL100 will then read back the entered number, (ignoring 15's and 13's) displaying it on the LED code pad.
- Page 10 AUDIBLE ALARM SOUNDS FIRE Steady Siren INTRUSION & PANIC Yelping siren CODE PAD CONTROL LIGHT INDICATORS ARMED RED: On when system is armed; off otherwise. Blinks as alarm memory if alarm was activated during arming cycle. READY GREEN: On when all zones are secure and/or isolated and the system is ready to arm;...
-
Page 11: Emergency Evacuation Plans
EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition. For example, the following steps are recommended by the National Fire Protection Association and can be used as a guide in establishing an evacuation plan for your building. Draw up a floor plan of your home. - Page 12 FOR SERVICE CONTACT: DL100 USER’S MANUAL DL100UC98 REV C (09-25-98)