Important Safety Instructions - Klipsch REFERENCE Floorstanding Speaker Owner's Manual

REFERENCE SERIES

IMPORTANT SAFETY INSTRUCTIONS

1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings.Install in accordance with the manufacturer's
instructions.
8. DO NOT install near any heat sources such as radiators,heat registers,stoves,or other
apparatus (including amplifiers) that produce heat.
9 . DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wider blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. PROTECT the power cord from being walked on or pinched,particularly at plugs,conve-
nience receptacles,and the point where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the manufacturer.
12. USE only with a cart,stand,tripod,bracket,or table specified by the manufacturer, or sold
with the apparatus.When a cart is used,use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.
14. REFER all servicing to qualified service personnel.Servicing is required when the apparatus
has been damaged in any wa y, such as power-supply cord or plug is damaged,liquid has
been spilled or objects have fallen into the apparatus,the apparatus has been exposed to
rain or moisture,does not operate normally, or has been dropped.
This symbol indicates that there are important operating and maintenance instructions
in the literature accompanying this unit.
This symbol indicates that dangerous voltage constituting a risk of electric shock is
present within this unit.
WARNING: To reduce the risk of fire or electrical shock,do not expose this apparatus
to rain or moisture.
RISKOFELECTRICSHOCK
WARNING: Voltages in this equipment are hazardous to life.No user-serviceable parts inside.
Refer all servicing to qualified service personnel.
CAUTION: Changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate this device.
ABOUT YOUR KLIPSCH PURCHASE
Thank you for your purchase of Klipsch floorstanding loudspeakers.After reading this manual
and connecting your system,you will hear the result of over 55 years of stringent engineering
and class-leading research and development.Like all Klipsch products,your floorstanding
loudspeakers feature Klipsch Tractrix Horn-loaded Technology—the guiding design for the first
®
Klipschorn developed in 1946 and for every product that has followed.Horn-loading allows
®
your speakers to deliver high sensitivity, low distortion, flat frequency response and wide
dispersion,which translates to unequaled power, detail and dynamics,the hallmarks of "The
Klipsch Sound."Please be sure to fill out the warranty card at the back of this manual or online
at www.klipsch.com so we are better able to serve you.Again,thank you for choosing Klipsch
and we hope that your speakers bring life to your music and movies for many years.
DONOTOPEN
UNPACKING AND ASSEMBLING THE SPEAKER
NOTE: Although this loudspeaker can be unpacked and set up by a single person,a helper will
make the job easier, not to mention safer, for speaker and owner alike.
The easiest way to remove the speaker from its carton is to turn the open end of the box down
so that it is resting on the floor, with the flaps spread out and away. Then pull the box straight up
and off.Remove any packing material from the speaker and grille,place it back in the carton,
and store in case you ever need to ship the loudspeaker. Locate the speaker's four stabilizing
feet and retaining screws,which are needed for the next step.
If the speaker is not already standing on its head,carefully turn it over so that the bottom is fac-
ing up.Near the corners are threaded inserts for attaching the feet.For each one,take one of
the supplied feet and align it so that its screw hole is over the insert.Thread one of the supplied
screws through and tighten it firmly with a phillips-head screwdriver. (See Figure 1.)
Once the feet are attached,install either a carpet spike or a rubber tipped bolt into the threaded
insert in each foot.The best sonic performance on carpeted surfaces will be achieved by using
the supplied spikes.Then,carefully turn the speaker right side up.Once installed,the speaker
must be lifted when moved to avoid carpet damage.The spikes are sharp; keep your feet clear!
Align the magnetic posts on the inside of the grille with the screws on the front of the speaker,
and it will snap into place.
PLACEMENT
Although your Reference Series speakers will perform well in a wide variety of locations,you will
get the most out of them by following some simple guidelines:
• The speakers require a few inches of clearance behind them to allow their ports to breat h e ,a n d
t h ey will sound best when they are at least two feet (60 centimeters) from any nearby walls.
• If possible,arrange both speakers so that they are equal distances from the floor and the wall
behind them.It can also help to have the left and right speakers at different distances from
their nearest side walls.This sort of staggering helps smooth the bass range.
• A ny speaker's bass output and response is strongly influenced by its distance from room
b o u n d a r i e s , such as walls and the fl o o r. Moving a speaker closer to a room boundary will
increase its bass output, while moving it aw ay will reduce the bass. Following the sugg e s t i o n s
above will typically yield good results with Klipsch Reference Series floorstanding speakers,
but you may find that you can " f i n e - t u n e " the sound by moving them slightly from side to side
or front to back until music recordings with strong bass content sound just right to you. Don't be
afraid to experiment.
Two-Channel Stereo System - Figure 2 shows a typical speaker arrangement for a two-channel
stereo system. A good starting point is to create an equilateral triangle with the speakers and your
listening position. Depending on the size of the room and the furniture arrangement, you may find
Figure 1