Encore E-7 Quick Start User Manual

ACTIVE ARMING – LOCK & ARM:
1. Press button on the transmitter.
2. The siren will chirp once and parking light will flash once indicating that
the system is now armed. The vehicle's doors will lock upon arming if
interfaced with the security system.
DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps, then you
have left a door, trunk, or hood lid ajar.
SILENT ARMING / DISARMING: Press the transmitter and
at the same time. This will arm or disarm your security system, No chirp
sound will be heard, arm / disarm confirmation will be through the vehicles
parking lights only.
SENSOR BY-PASS: Press the button two times within 5 seconds will
arm the security system and by-pass the shock sensor.
PASSIVE ARMING (Programmable)
Active arming / disarming is controlled by your security system via the
remote transmitter. This security system is equipped with an optional
Passive Arming feature which allows the security system to arm 30
seconds after the last door is closed. Operation is as follows.
1. Turn the ignition to the "OFF" position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for
30 seconds. If you reopen any door / hood / trunk, the security system
LED will stop flashing. It will begin flashing again once all vehicle
entrances are closed.
3. After the 30-second time has elapsed, the security system will
automatically "ARM". The siren will chirp [1] time and the parking lights
will flash [1] time.
PASSIVE ARMING WITH PASSIVE DOOR LOCKING
The vehicle doors will automatically lock after the passive arming cycle
has been completed.
PASSIVE ARMING BY-PASS: While the system is disarmed, Press the
button twice, the system will respond with [1] chirp and LED will turn
"ON". The security system will remain in this temporary state for as long
as you wish. To exit passive by-pass, press the transmitter
buttons and the system will return to normal status.
ACTIVE DISARMING – UNLOCK & DISARM:
1. Press button on the transmitter.
2. The siren will chirp twice and the parking lights will flash twice
indicating that the security system is now disarmed. The vehicle's
doors will unlock.
TAMPER DISARMING: If the alarm is triggered, upon disarm the system's
siren will chirp 4 times, and the parking lights will flash 3 times telling you
the alarm has been triggered during the last armed state.
PATHWAY ILLUMINATION: When receiving an unlock /disarm signal, this
feature will turn the parking lights "ON" for 30 seconds and for 10 seconds
upon the lock signal. (Programmable)
AUTOMATIC RE-ARM: If this feature is selected, the security system will
automatically re-arm itself in 60 seconds after disarming with remote
transmitter. Automatic rearm will cancel if any door is opened before the 60
seconds timer has elapsed.
DISARMING WITHOUT A TRANSMITTER:
The Override function may be used if the remote transmitter is lost or
inoperative.
1. Enter the vehicle and turn the ignition switch to the 'ON' position.
2. (Alarm will sound.)
3. Within 10 seconds push and release the valet switch. The alarm will stop
sounding and enter the disarm mode. You can now start and operate the
vehicle normally.
VALET MODE: (System is in Disarm Mode)
The valet switch allows you to temporarily bypass all alarm function,
eliminating the need to hand your transmitter to parking attendants or
garage mechanics. When the system is in valet mode, all alarm functions
and remote start functions are bypassed, however, the remote panic
feature and remote door locks will remain operational. To use the valet
mode, the system must first be disarmed either by using your remote
transmitter, or by operating the Manual Override sequence.
a). Under disarm mode, turn the ignition to "ON" position.
b). Press and hold valet switch for 2 seconds until the LED turns ON
solid. The LED will remain on as long as the system is in 'valet mode'.
Exit Valet Mode:
a). Turn ignition 'ON'.
b). Push and hold valet switch for 2 seconds, The LED will turn off
indicate the system are exiting the valet mode.
CAR LOCATOR
Under armed mode, press the button to active car locator function. The
siren will chirp 6 times. The parking light will flash 12 times, for you to
easily locate your car.
PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger
the alarm in case of emergency.
Press and hold the button for 3 second. The alarm will immediately
buttons
sound.
To stop the alarm, press the trunk button on the remote control.
If the button is not pressed, the alarm will automatically stop after 30 seconds.
TRIGGER THE SYSTEM
When armed, your vehicle is protected as follows:
Light impact will trigger the warn-away signal.
Heavy impacts / Doors open /(if installed) Hood open / (if installed) Trunk
open / Turning on the ignition key will trigger the programmed sequence.
The starter disable relay (if installed) prevents the vehicle's starter from
cranking. The siren, horn, parking lights, and dome light will turn on alerting
of an intrusion for 30 seconds. Then it will stop and automatic reset and re-
arm. If the any one of the sensors or detectors is still active, the alarm
system will sound a maximum of 3 times of 30 seconds cycles.
NOISE ABATEMENT CIRCUIT: Your system has a "Noise Abatement
Circuit". It prevents annoying repetitive trigger sequences due to faulty door
pin switches or environmental conditions such as thunder, jackhammers,
airport noise, etc.
Here's how "Noise Abatement Circuit" works: The shock sensor triggers
five times, the "Noise Abatement Circuit" will interpret this pattern of
th
triggers as a false alarm. After the 5 trigger, the "Noise Abatement Circuit"
ignores, or bypasses, that sensor or switch until a different sensor or switch
is triggered.
SYSTEM'S TRIGGER CHECK (For two-way transceiver operation only)
Press & hold + button of LCD remote until 1 beep sound, press
button (see LCD Remote manual Table 1) to activate system trigger check.
Note: If the system has no response then you are out of range.
or
SYSTEM'S STATUS CHECK (For two-way transceiver operation only)
Press & hold + button of LCD remote until 1 beep sound , press
button (see LCD Remote manual Table 1) to activate system trigger
check. Note: If it has no response then you are out of range.
TRUNK RELEASE: Press and hold button on the transmitter for two
seconds to remotely control the trunk release.
CHANNEL4 TIMER CONTROL OUTPUT:
Press the transmitter and buttons at the same time to active Channel
4 function.
Channel 4 is user-programmable timer output. You may program the built-
in timer to send a ground signal for any time duration from 1 second to 120
seconds. For instance, this timer output may be used to turn on the
headlight, power window or sunroof.
CHANNEL5 TIMER CONTROL OUTPUT:
Press the transmitter and buttons at the same time to active
Channel 5 function.
Channel 5 is user-programmable timer output. You may program the built-
in timer to send a ground signal for any time duration from 1 second to 120
seconds. For instance, this timer output may be used to turn on the
.
headlight, power window or sunroof
Clear the Flashing Icon and Melody Sound: The Transmitter will reset the
flashing icons the next time the Ignition is cycled to the ON position.
Stopping The Trigger Melody Sound: When the alarm is triggered, the LCD
screen will alert the user through a melody sound and a flashing trigger icon.
Press any button on the LCD remote transmitter to stop melody sound.
ANTI CAR- JACKING (Programmable)
Warning: If you don't need the carjacking function in this alarm system, be
sure to set carjacking feature "OFF". This systems default setting is "OFF" for
all carjacking modes.
Please download the complete manual for this and other
advanced functions.
www.encoreautomotivesystems.com
ADVANCED USER'S MODE:
LCD REMOTE TRANSCEIVER OPERATION:
Transmitter button LCD Feature & remark
Press + Backlight turns on for 3 seconds
Press & Hold + U 01 Press & Hold
for 2 seconds (until 1 (chirp one time )
chirp is heard) LCD display show U: 01 = enter 1
programming of LCD Remote
Press button Press
status.
Press button Press
trigger condition
Press button PRESS
1 / CAR 2
Press & hold button Press & hold
on
for 2 sec. Lock On (1 beep) / Off (2 beep, default =
= Button
Off)
Lock
Press & hold button Press & hold
for 2 sec. or Melody mode selection (default =
Melody)
Press & hold Press & hold
button for 2 sec. Count
20m/30m/1HR / 1.5HR / 2HR)
Press & hold button Press & hold
for 2 sec. Beep Sound mode Enable (1 beep) /
Disable (2 beeps, default = disable)
Table 2: two beeps to confirm
.
Transmitter button LCD Display System feature & remark
Press & hold button clock time adjust
+ for 3 12 is flashing
seconds (Two chirps increase "Hour" digit, adjust hour from
will be heard) 0 to 12.
Complete adjust "Hour, "Press
button.
00 is flashing "Minute" from 0 to 59.
Press
setting.
Alarm Clock adjust
increase "Hour" digit, adjusts clock
hour from 0 to 12.
12 is flashing
Complete adjust "Hour, "Press
button.
"Minute" from 0 to 59.
00 is flashing
Press
setting.
Count Down Timer
setting
+ for 2 seconds
button = check the vehicle's
Press & hold button
+ for 5
button = check the system
seconds (chirp x 3)
button FOR OPTION OF CAR
button for 2 sec. Button
Exit : Press + buttons or not press any button within 10 seconds, it will
exit remote programming mode automatically.
Low Battery Indication:
When the power of the battery weakens, it has two short "bi" sound and flash
button for 2 sec. Vibrator
icon while pressing the button of the LCD screen transceiver.
Stop The Trigger Melody Sound: While triggering the alarm the LCD screen
will alert user through melody sound and flashing trigger icon, press any button
on the LCD remote transmitter to stop melody sound only, the remote control
button for 2 sec. Fast buttons will not send a command to the system.
Down Timer (Off / 10m/
button for 2 sec. Button
E
ncore Automotive Systems, LLC. All
rights reserved
For Warranty information, Please go to
www.encoreautomotivesystems.com
complete user's manual. For customer service, please call us
toll free @ (855) GO-ENCORE 855.463.6267. 8:00-5:00 PST
Thanks for your purchase!
or button to decrease or
or button - Adjusts clock
button complete clock
or button to decrease or
or button - Adjusts clock
button complete Alarm clock
or adjust parking "Hour"
(value from 0 to 2).
0 :00
Complete adjust "Hour, "Press
0 is flashing
button.
or adjust parking "Minutes"
(value from 0 to 30).
Press button complete count
down timer setting.
Full battery
Power Save mode : ON ? OFF
LCD remote transceiver uses "0"
icons flash
current to save the battery power.
and download the