SERVICE MANUAL COLOR MONITOR HP V7650 Series THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS LIABILITY FOR CHANGES,...
2. PRECAUTIONS AND NOTICES SAFETY PRECAUTIONS Observe all caution and safety related notes located inside the display cabinet. Operation of the display with the cover removed, may cause a serious shock hazard from the display power supply. Work on the display should not be attempted by anyone who is not thoroughly familiar with precautions necessary when working on high voltage equipment.
PRODUCT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety visual inspections and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Before replacing any of these components read the parts list in this manual carefully.
3. OPERATING INSTRUCTIONS This procedure gives you instructions for installing and using the Color display. Position the display on the desired operation and plug the power cord into a convenient AC outlet. Three-wire power cord must be shielded and is provided as a safety precaution as it connects the chassis and cabinet to the electrical conduit ground.
4. ADJUSTMENT 4-1 ADJUSTMENT CONDITIONS AND PRECAUTIONS Approximately 30 minutes should be allowed for warm up before proceeding. Adjustments should be undertaken only on those necessary elements since most of them have been carefully preset at the factory. 4-2 MAIN ADJUSTMENTS FUNCTION LOCATION DESIGNATION...
Page 10
H-SIZE H-MOIRE REDUCE H-CENTER MOIRE DISABLE V-SIZE NO USE V-CENTER NO USE PINCUSHION NO USE PARALLELOGRAM V-LINEARITY PIN-BALANCE V-LINEARITY TRAPEZOID TOP CORNER ROTATION BOT CORNER NO USE NO USE CONTRAST MAX-HSIZE MODIFY BRIGHTNESS MAX-VSIZE MODIFY R-BIAS MAX-TRAPEZOID MODIFY G-BIAS BI SELECT FUNCTION R-BIAS DEGAUSS R-GAIN...
Page 11
3. White Balance, Luminance adjustment: A. Bias (Raster) adjustment: (a) Set mode8 1024×768 @85Hz full white pattern(100% white field). (b) To make the adjustment condition is under the Factory preset OSD menu. Same as step 2-B. (c) Warm up more than 20 minutes. (d) Put the probe in the middle of screen, Brightness set to maximum.
Page 12
5. Purity Adjustment A. Be sure that the display is not being exposed to any external magnetic fields. B. Ensure that the spacing between the Purity, Convergence, Magnet, (PCM), assembly and the CRT stem is 29mm. (See below diagram) C. Produce a complete, red pattern on the display. Adjust the purity magnet rings on the PCM assembly to obtain a complete field of the color red.
5. CIRCUIT DESCRIPTION 5-1 MICRO CONTROLLER CIRCUIT MICRO Controller The IC101 contains a 6502/8051 8-bit CPU core, 512 bytes of RAM, 16K bytes of ROM,14 channel 8 bit PWM D/A converters, 2 channel A/D converters for key detection, one 8 bit pre-loadable base timer, internal H-sync and V-sync signals processor providing mode detection, watch- dog timer preventing system from abnormal operation, and an I²C bus interface.
X-ray Protection The X-ray protection input pin25 provides a voltage detector with a precise threshold. If the voltage exceeds this threshold for a certain time, an internal latch switches the whole IC into protection mode. In this mode several pins are forced into defined states: Pin28 (BDRV) is floating Pin26 (HDRV) is floating Vertical Oscillator...
6.TROUBLE SHOOTING CHART 6-1 NO RASTER, CRT RELATIVE CIRCUIT PROBLEMS CHECK MAIN PCB POWER CHECK MAIN PCB POWER SUPPLY SUPPLY 47.0V,13V 53V, 14V, 78V CHECK POWER SAVING CIRCUIT, H-SYNC, V-SYNC SIGNAL Q909, Q910 CHECK THE HIGE VOLTAGE OF CHECK THE HIGE VOLTAGE CRT ABOUT 23~24KV REFER ITEM S.M.P.S.
Page 16
2.ABNORMAL VIDEO LEVEL ON SCREEN 3. ABNORMAL DDC (PLUG & PLAY)