Moxa Technologies IEX-402-SHDSL Series Hardware Installation Manual
  1. Manuals
  2. Brands
  3. Moxa Technologies Manuals
  4. Extender
  5. IEX-402-SHDSL Series
  6. Hardware installation manual
Moxa Technologies IEX-402-SHDSL Series Hardware Installation Manual

Moxa Technologies IEX-402-SHDSL Series Hardware Installation Manual

Managed shdsl ethernet extender
Hide thumbs Also See for IEX-402-SHDSL Series:
Table of Contents

Advertisement

Quick Links

IEX-402-SHDSL Series
Hardware Installation Guide
Moxa Managed SHDSL Ethernet Extender
First Edition, October 2012
 2012 Moxa Inc. All rights reserved.
P/N: 1802004020010

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IEX-402-SHDSL Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Moxa Technologies IEX-402-SHDSL Series

Summary of Contents for Moxa Technologies IEX-402-SHDSL Series

  • Page 1 IEX-402-SHDSL Series Hardware Installation Guide Moxa Managed SHDSL Ethernet Extender First Edition, October 2012  2012 Moxa Inc. All rights reserved. P/N: 1802004020010...

  • Page 2: Package List

    10/100BaseT(x) port and a DSL interface that provides an economical solution for your Ethernet connections. Utilizing SHDSL technology over copper wires, the IEX-402-SHDSL series supports data rates of up to 15.3 Mbps and long transmission distance of over 8 km. Advanced managed functionality provides highly reliable communication for networks.
  • Page 3 IEX-402-SHDSL Panel Layout Front Panel View 1. Terminal block for power input (PWR1, PWR2) 2. Power input PWR1/PWR2 LED 3. State LED 4. Fault LED 5. 10/100BaseT(X) Port 6. DSL speed/SNR LED 7. Detachable 2-contact DSL Port 8. Link/ACT LED 9.
  • Page 4 Mounting Dimensions (unit = mm[inches]) - 4 -...

  • Page 5: Din-Rail Mounting

    DIN-Rail Mounting The aluminum DIN-Rail attachment plate should already be fixed to the back panel of the IEX-402-SHDSL when you take it out of the box. If you need to reattach the DIN-Rail attachment plate, make sure the stiff metal spring is situated towards the top, as shown in the following figures.

  • Page 6: Wiring Requirement

    NOTE Before tightening the screws into the wall, make sure the screw head and shank size are suitable by inserting the screw into one of the keyhole-shaped apertures of the wall mounting plates. Do not screw the screws in completely—leave about 2 mm to allow room for sliding the wall mount panel between the wall and the screws.

  • Page 7: Wiring The Redundant Power Inputs

    Wiring the Redundant Power Inputs Both power inputs can be connected simultaneously to live DC power sources. If one power source fails, the other live source acts as a backup, and automatically supplies the IEX-402-SHDSL with power. The two 2-contact terminal block connectors on the IEX's top panel are used for IEX's two DC power inputs.
  • Page 8 RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring DSL Port Connection The DSL port located on the IEX-402-SHDSL has two connection options. One is the RJ45 connector interface (2-wire on pin 4 and pin 5), the other is the screw detachable interface.
  • Page 9 RS-232 Console Port Connection The IEX-402-SHDSL has one RS-232 (10-pin RJ45) console port, located on the top panel. Use either an RJ45-to-DB9 (see the cable following wiring diagrams) to connect the IEX-402-SHDSL‘s console port to your PC’s COM port. You may then use console terminal software, such as Moxa PComm Terminal Emulator, to access the IEX-402-SHDSL’S serial console.

  • Page 10: Restore Factory Defaults Button

    NOTE Do NOT power off the Ethernet extender when loading default setting DIP Switches Settings The IEX-402-SHDSL series provides 4 hardware DIP switches for quick configurations, based on terminal type (CO/CPE), DSL signal measurement type (Speed/SNR), communication media type (ANNEX A/ANNEX B) and data rate mode (STD/Turbo).

  • Page 11: Led Indicators

    rate follows defined defined Turbo mode value standard mode value LED Indicators Color State Description Power is being supplied to the power input PWR1 PWR1 AMBER Power is not being supplied to the power input PWR1 Power is being supplied to the power input PWR2 PWR2 AMBER...

  • Page 12: Specifications

    DSL Speed/SNR LED Indicator Five Levels of SNR/SPEED Setting Turbo Speed (K bits) 10297 – 15304 5697 – 10296 3457 – 5696 1025 – 3456 192 – 1024 STD Speed (K bits) 4609 – 5760 3073 – 4608 2049 – 3072 769 –...
  • Page 13 Reverse Polarity Present Protection Physical Characteristics Housing Metal, IP30 protected Dimension 35 x 130 x 105 mm Weight 0.29 kg Installation DIN-Rail, Wall Mounting (optional kit) Environmental Limits Operating Temperature -10 to 60°C (32 to 140°F); -40 to 75°C (-40 to 167°F ) for -T models Storage Temperature -40 to 85°C (-40 to 185°F) Ambient Relative...

Table of Contents