Table of Contents
Advertisement
Quick Links
Black Box Tech Support: FREE! Live. 24/7.
Tech support the
way it should be.
Great tech support is just 20 seconds away at
724-746-5500 or blackbox.com.
About Black Box
Black Box Network Services is your source for more than 118,000 networking
and infrastructure products. You'll find everything from cabinets and racks and
power and surge protection products to media converters and Ethernet switches
all supported by free, live 24/7 Tech support available in 20 seconds or less.
©
Copyright 2010. All rights reserved.
724-746-5500 | blackbox.com
040-MT1400-001 7/10
MT14230A-SM-SC
MT14320A-SM-LC
DFCS 4xT1/E1 Multiplexer
Multiplexes up to four T1/E1 copper circuits and
one optional 10/100 Ethernet UTP port onto a
fiber optic link.
Supports multimode and singlemode fiber
SC or LC connectors
Supports local and remote fiber and copper loopback modes
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
Customer
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax
Support
724-746-0746 • Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence,
Information
PA 15055-1018 • Web site: www.blackbox.com • E-mail: info@blackbox.com
July 2010
MT1415A-MM-SC
MT1430A-SM-SC
MT1405A-MM-SC
MT1415A-MM-LC
MT1430A-SM-LC
MT1405A-MM-LC
Advertisement
Table of Contents
Related Manuals for Black Box MT14230A-SM-SC
Summary of Contents for Black Box MT14230A-SM-SC
- Page 1 724-746-5500 or blackbox.com. About Black Box Black Box Network Services is your source for more than 118,000 networking and infrastructure products. You’ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free, live 24/7 Tech support available in 20 seconds or less.
-
Page 2: Specifications
DFCS 4xT1/E1 Multiplexer DFCS 4xT1/E1 Multiplexer DFCS 4xT1/E1 Multiplexer DFCS 4xT1/E1 Multiplexer Specifications Defi nitions of Terms FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS Alarm Indication Signal (all 1’s) BERT Bit Error Rate Test This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the Loss of frame manufacturer’s instructions, may cause inter ference to radio communication. - Page 3 DFCS 4xT1/E1 Multiplexer NOM Statement Specifi cations 5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca, Model Type 4xT1/E1 MUX etc.. Protocols (TDM) ANSI: T1.403, T1.102, AT&T: T62411, 6.
-
Page 4: Led Indicators
DFCS 4xT1/E1 Multiplexer LED Indicators 17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean Verify the Transport module is operational by viewing the LED indicators. derramados sobre la cubierta u orificios de ventilación. LED Function “Legend” Color Off State ON / Blinking State... -
Page 5: Trademarks Used In This Manual
DFCS 4xT1/E1 Multiplexer Trademarks Used in this Manual TRADEMARKS USED IN THIS MANUAL LED Indicator Function Black Box and the Double Diamond logo are registered trademarks of Stat Local Remote BB Technologies, Inc. No power Green - 1Hz Normal Not peered with remote Mux (searching) -
Page 6: Operation
DFCS 4xT1/E1 Multiplexer Operation Product Overview 4) Verify Operation Verify the MUX is operational by viewing the LED indicators. DFCS 4xT1/E1 MUX multiplexes up to four T1/E1 copper circuits and one optional 10/100 Ethernet UTP port onto a fi ber optic link. The aggregated services can be extended LED Legend Function Color... -
Page 7: Installation And Configuration
DFCS 4xT1/E1 Multiplexer Installation and Configuration 3) Connect Cables When using the SFP model, insert the SFP Fiber transceiver into the Port 1 SFP receptacle on the Transport module NOTE: The release latch of the SFP Fiber transceiver must be in the closed (up) position before insertion. -
Page 8: Installation
DFCS 4xT1/E1 Multiplexer Installation SW5: Circuit Test (C/T) Mode “Off / On” When this DIP-switch is in the “Off” down position (default), the Circuit Test Mode is disabled. When this DIP-switch is in the “On” up position, the Circuit Test Mode is enabled.