Black & Decker GH750 Instruction Manual page 20

20 • ENGLISH
which it is able to cut effectively.
► Use the right tool: Do not use this tool for any job except
that for which it is intended.
► Don't overreach: Keep proper footing and balance at all
times.
► Don't abuse cord: Don't yank cord from power supply.
Keep cord from heat, oil, and sharp edges.
► Damage to unit: If you strike or become entangled with
a foreign object, stop tool immediately, unplug, check for
damage and have any damage repaired before further
operation is attempted. Do not operate with a broken hub
or spool.
► Damage to cord: Keep power cord away from rotating
line. If you damage the cord, unplug it from the power
supply before moving the tool or examining the damage.
A damaged cord must be replaced before further use.
► Disconnect tool: When not in use, when replacing line,
or prior to cleaning.
► Avoid dangerous environmental conditions: Do not
use electric tools in damp or wet locations. Follow all
instructions in this instruction manual for proper operation
of your tool. Don't use the tool in the rain.
► Do not operate portable electric tools in gaseous or
explosive atmospheres: Motors in these tools normally
spark, and the sparks might ignite fumes.
► Store idle tools indoors: When not in use, tools should
be stored indoors in a dry, locked-up place out of reach of
children.
► Ground fault circuit interrupter (GFCI) protection
should be provided on the circuits or outlets to be
used for the gardening appliance: Receptacles are
available having built in GFCI protection and may be used
for this measure of protection.
► Secure extension cord: Using the cord retainer.
► Stay alert: Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
► Maintain appliances with care: Follow instructions in
maintenance section. Inspect extension cords periodically
and replace if damaged. Keep handles dry, clean and free
from oil and grease.
► Check damaged parts: Before further use of the appliance,
a guard or other part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other condition that may affect its
operation. A guard or other part that is damaged should
be properly repaired or replaced by an authorized Service
Center unless otherwise indicated elsewhere in this manual.
Warning! When servicing double insulated tools, use only
identical replacement parts. replace or repair damaged cords.
Warning! To prevent electrical shock hazard, use only with
an extension cord suitable for outdoor use. Always connect
extension cords to a fused line or one protected by a circuit
breaker.
Safety Warnings and Instructions:
Polarized Plugs
To reduce the risk of electric shock, this equipment has a
polarized plug (one blade is wider than the other) and will
require the use of a polarized extension cord. The appliance
plug will fit into a polarized extension cord only one way. If the
plug does not fit fully into the extension cord, reverse the plug.
If the plug still does not fit, obtain a correct polarized extension
cord. A polarized extension cord will require the use of a
polarized wall outlet. This plug will fit into the polarized wall
outlet only one way. If the plug does not fit fully into the wall
outlet, reverse the plug. If the plug still does not fit, contact a
qualified electrician to install the proper wall outlet. Do not
change the equipment plug, extension cord receptacle, or
extension cord plug in any way.
Minimum Gage for Cord Sets
Volts Total length of cord in feet
120V 0-25
220V 0-50
Ampere Rating
More No more American wire gage
than than
0- 6 18
6- 10 18
10- 12 16
12- 16 14
Safety Warnings and Instructions:
Extension Cords
Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized cord
will cause a drop in line voltage resulting in loss of power and
overheating. The table shows the correct size to use depending
on cord length and nameplate ampere rating. If in doubt, use
the next heavier gauge. The smaller the gauge number, the
heavier the cord. If the extension will be used outside, the cord
must be suitable for outdoor work. The letters "WA" on the
cord jacket indicate that the cord is suitable for outdoor use.
ASSEMBLY/ADJUSTMENT SET-UP
Assembly tools required (not supplied):
Phillips Screwdriver
Attaching the Two Piece Guard
Warning! Unplug the tool before attempting to attach the
guard. Never operate tool without guard firmly in place. The
26-50 51-100 101-150
51-100 101-200 201-300
16 16 14
16 14 12
16 14 12
12 Not recommended