Advertisement
Preparation
General
1
2
[SRC] (Source)
Set your car's ignition switch
Press [SRC] (PWR: Power).
selects a source.
A
C
C
to the ACC or ON position.
O
N
[PWR] (Power)
toggles power on/off.
The demonstration message appears for initial
5
Turn [VOL] counterclockwise.
use.
For using the remote control, press [0] ().
1
Set your car's ignition switch to the ACC or
ON position.
2
Press [SRC] (PWR: Power).
Notes:
[SQ] (Sound Quality)
3
Hold down [VOL] (PUSH SEL: Select) for
selects a sound type (SQ).
• To return to the regular mode, press [DISP].
2 sec. or more to open the function menu.
• Refer to the section on "Function Settings".
4
Press [VOL] (PUSH SEL: Select) to select
• When "NO USB" (\CQ-RX420U\ \CQ-RX320L\) or "NO
DISC" is displayed, the Demonstration cannot be cancelled.
DEMO.
Pull the insulation film out from
Note: Battery Information:
the backside of the remote control
Battery Type: Panasonic lithium battery (CR2025) (Included
gently.
in the remote control)
Battery Life: Approximately 6 months under normal use (at
room temperature)
Power On/Off
Set your car's ignition switch to the ACC or ON position.
The 12-hour system is used for the clock.
5
Power on: Press [SRC] (PWR).
Adjust the minute.
1
Power off: Hold down [SRC] (PWR) for more
Press [DISP].
Minute entered
(clock display)
2
Hold down [DISP] for more than
[9]: sets the minute ahead.
2 seconds.
[:]: sets the minute back.
Source Selection
Hour blinks
6
Press [DISP].
Press [SRC] to change the source.
Completed
3
Adjust the hour.
\CQ-RX420U\
Notes:
Hour entered
Radio
• "ADJUST" is displayed before adjusting the clock.
• Hold down [:] or [9] to change numbers rapidly.
• When "NO DISC" is displayed, the clock cannot be
[9]: sets the hour ahead.
adjusted.
[:]: sets the hour back.
System-up
4
Connector
Press [DISP].
Clock Display at Power Off
(Below)
Press [DISP] to change the display.
Minute blinks
Display off
Note: Select USB Connector mode to operate the iPod
series connected with USB connector.
Guidebook)
Clock display (Default)
(Continued below)
\CQ-RX320L\
Remote Control Unit
Notes:
• This instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded)
• Aim the remote control at the remote sensor and operate it.
[BAND] (SET)
[0] to [9]
selects a band in the tuner source, toggles pause/play in player source,
selects a preset station (1 to 6),
executes the APM (Auto Preset Memory) in tuner source
presets the current station (Hold it down for more than
(Hold it down for more than 2 seconds).
\CQ-RX120U\ \CQ-RX120L\
2 seconds.),
inputs the number in direct selection.
[SRC] (SOURCE)
[MENU] (SEL: Select)
Radio
[#] (NUMBER)
selects a source.
selects the items in the audio menu.
executes the direct selection.
(POWER)
[RANDOM] [SCAN] [REPEAT]
toggles power on/off.
[VOL] (volume)
toggles on/off each play mode.
adjusts the volume, and selects the
[] []
value in the audio menu, etc.
down/up the frequency (Hold it down for more than
0.5 seconds and release it for seek tuning.)
[MUTE]
AUX1 Connector
[] []
toggles mute on/off.
skip to the previous/next folder in player mode.
AUX IN*:
(Only for remote control unit)
[:] [9]
Note: You can select mute or
skip to the previous/next track/file in player mode. Hold
attenuation.
(
"Function Settings")
it down for fast reverse/fast forward.
\CQ-RX420U\
[DISP] (Display)
switches the information on display,
Direct Access
and exits the audio menu.
Note: The connector is labeled "AUX1", but it appears on the
A track (CD mode), file, folder (MP3/WMA/AAC mode) can
display as "<AUX IN>".
be directly selected.
2 Put a battery in the
Example: Track number 5
case with (+) side
1
Press [#] (NUMBER).
facing up.
3 Put the case back.
2
Press [5].
3
Press [BAND] (SET).
Notes:
Warning
• To suspend direct selection, press [DISP].
Keep batteries and insulation film out of reach of infants.
• For folder selection, enter a number after pressing [#]
Batteries and insulation film can be ingested, so keep
(NUMBER) twice.
them out of the reach of infants. If an infant ingests a
Functions only on Main unit
battery or insulation film, please seek immediate medical
attention.
The following functions are not available on remote control
unit.
Caution
• SQ selection
• Scroll
• Remove and dispose of an old battery immediately.
• Disc eject
• Tag on/off
• Do not disassemble, heat or short a battery. Do not
throw a battery into a fire or water.
Battery Replacement
• Follow local regulations when disposing of a battery.
• Improper use of batteries may cause overheating, an
1 Remove the battery holder with
Tough pointed object
explosion or ignition, resulting in injury or a fire.
the remote control unit placed on
a flat surface.
Notice
1 Stick your thumbnail into
This product contains a CR Coin Cell Lithium Battery
the groove, and push the
which contains Perchlorate Material - special handling
holder in the direction of
may apply.
the arrow, and at the same
2
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
time.
1
2 Pull it out in the direction
Notes: Battery Information:
of the arrow using a tough
Back side
Battery Type: Panasonic lithium battery (CR2025) (Included
pointed object.
in the remote control)
Battery Life: Approximately 6 months under normal use (at
room temperature)
Radio (AM/FM)
[SRC] (Source)
Remote Control Sensor
selects a source.
[VOL] (Volume)
[DISP] (Display)
switches the information on the
display.
[BAND]
selects a band in the radio source.
[APM] (Auto Preset Memory)
executes APM in the radio source. (Hold it
down for more than 2 seconds.)
AUX1 Connector (3.5 mm stereo)
1
From line output of external sound/audio device (ex. Silicon-
Press [SRC] to select the radio source.
audio player, HDD player, etc.)
2
Press [BAND] to select a band.
Caution
• Set the volume level to low enough before the AUX
connection is completed.
3
Select a station.
Failure to observe this, the loud noise may come out and
damage your speakers and your hearing.
Volume Adjustment
Band
Frequency
(Setting Range: 0 to 40, Default: 18)
Turn [VOL].
than 1 second.
lights while receiving an FM stereo signal.
Up to 6 stations can be preset in AM, FM1, FM2, and FM3 respectively.
USB Connector
Preset stations can be simply called up by pressing [1] to [6].
\CQ-RX420U\ \CQ-RX320L\
Auto Preset Memory (APM)
When an optional USB memory is connected:
When loading MP3/WMA/AAC data \CQ-RX420U\
Disc Player
With this operation, stations with good receiving conditions
When loading MP3/WMA data \CQ-RX320L\
can be automatically stored in the preset memory.
1
Select a band.
When an optional USB memory is not connected:
2
AUX 1
*
USB Connector
Hold down [BAND] (APM) for more than
2 seconds.
(Right)
The preset stations under best receiving conditions are received
for 5 seconds each after presetting the stations (SCAN). To stop
scanning, press one of the buttons from [1] to [6].
(
System Upgrade
Note: New stations overwrite existing saved stations.
System-up Connector
Player (Disc Player)
\CQ-RX420U\
Radio
Disc Player
When an optional device is connected:
Shift to connected device
When connecting CD changer
AUX
*
USB Connector
Notes:
• The power will be turned on automatically when a disc is loaded.
(Right)
When connecting iPod
• A disc which has both CD-DA data and MP3/WMA/AAC data on it
may not be reproduced normally.
When connecting XM Receiver
Disc Player
AUX
*
When connecting Sirius Receiver
Disc slot
When connecting Bluetooth
®
Unit
takes a disc in with the
Printed side up
printed side facing up.
OR
When an expansion module is connected:
The devices connected to the ports 1 to 4 are activated in
[SRC] (Source)
sequence after shifting to AUX2 (device connected to the
selects a source.
AUX terminal of the expansion module).
Source connected to the
[DISP] (Display)
Expansion Module
switches the information on the display.
(CY-EM100U, option)
\CQ-RX420U\
Note: For information about connectable devices, refer to
the System Upgrade Guidebook or the instruction manual for
(1;) (Play/Pause)
[:] [9]
each device.
toggles pause/play in the player source.
skip to the previous/next track/file in
\CQ-RX320L\
the player mode.
Note: For information about connectable devices, refer to the
Hold down either of them for fast
Operating Instructions USB or the instruction manual for each
reverse/fast forward.
device.
Notes:
• Do not insert a disc when the
indicator lights.
• Refer to the section of "Notes on Discs" and "Notes on MP3/WMA/
AAC".
• This unit does not support 8 cm {3} discs.
1
Press [SRC] to select the Disc Player
source.
2
Select a desired portion.
Track/File Selection
Press [:] / [9].
Note: To perform fast forward/reverse, hold down either of
them.
Disc Player (CD-DA disc):
Previous/next track
Disc Player (MP3/WMA/AAC disc):
Previous/next file
Folder Selection (MP3/WMA/AAC)
Press [] / [].
Audio Settings
[TUNE :] [TUNE 9]
[VOL]
down/up the frequency. (Hold it down for more than 0.5 seconds
selects a value in the audio menu.
and release it for seek tuning.)
(PUSH SEL) (Push to select)
selects items in the audio menu.
[DISP] (Display)
exits from the audio menu.
1
Preset buttons [1] to [6]
Press [VOL] (PUSH SEL) to open the audio menu.
selects a preset station in the radio source,
Note: If no operation takes place for more than 5 seconds in audio setting (2 seconds in the volume adjustment,
and presets the current station. (Hold it down for more than
10 seconds in the SQ adjustment), the display returns to the regular mode.
2 seconds.)
2
3
Press [VOL] (PUSH SEL) to select a
Frequency Adjustment
mode to be adjusted.
[TUNE :]: Lower
Volume
[TUNE 9]: Higher
(Setting Range: 0 to 40, Default: 18)
Note: Hold down for 0.5 sec. or more and release for
station search.
Bass
Preset Station Selection
(Setting Range: –12 dB to +12 dB by 2 dB, Default: 0 dB)
Press the corresponding preset button from
[1] to [6] to tune in a preset station.
Treble
(Setting Range: –12 dB to +12 dB by 2 dB, Default: 0 dB)
Display Change
SQ Adjustment
Preset Number
Press [DISP] to change the display.
(Tone/SQ adjustable range: 12 dB to 12 dB (by 2 dB))
Radio mode display
Setting range:
(Default)
SQ Low/Bass:
±12 dB (at 60 Hz, 80 Hz, 100 Hz, 200 Hz)
SQ Mid:
±12 dB (at 500 Hz, 1 kHz, 2 kHz, 3 kHz)
Clock display
SQ High/Treble: ±12 dB (at 10 kHz, 12 kHz, 15 kHz, 18 kHz)
Balance
(Setting Range: 15 levels each, Default: CNT (center))
Fader
Manual Station Preset
(Setting Range: 15 levels each, Default: CNT (center))
1
Tune into a station.
Notes:
2
Hold down one of the preset buttons from
• The volume can also be adjusted directly using [VOL] on the main unit. (
[1] to [6] for more than 2 seconds.
• For further information on SQ (Sound Quality) settings, refer to "Sound Control".
• Do not activate SQ and Bass/Treble at the same time to avoid causing sound distortion.
(blinks once)
\CQ-RX420U\
• The sequence and contents of setting items may depend on the conditions of devices to be connected. For further information,
Note: New stations overwrite existing saved stations.
refer to the System Upgrade Guidebook or the instruction manuals for the devices to be connected.
\CQ-RX320L\
• If the fader is set to front, the pre-amp. output (rear) is decreased.
Playable Audio File
CD-DA Mode Display
Display Change
Lights when the disc is loaded.
Press [DISP] to change the display.
CQ-RX420U
MP3/WMA/AAC
CQ-RX320L
MP3/WMA
Disc Player
CQ-RX120U
MP3/WMA
(CD-DA disc):
CQ-RX120L
MP3/WMA
Notes for AAC playback is only for the model CQ-RX420U.
Track number
Play time
Play Mode indicators
[] []
[<] (Eject)
skip to the previous/next folder.
ejects the disc.
MP3/WMA/AAC Mode Display
Folder number
File number
Play Mode indicators
Lights when folder random/repeat/scan is on.
[4] (RANDOM)/[5] (SCAN)/[6] (REPEAT)
toggles on/off each play mode.
[3] (SCROLL)
scrolls the information on display.
Notes:
• For scrolling text, press [3] (SCROLL).
• "NO TEXT" is displayed when there is no information on the disc.
• If you insert an 8 cm {3} disc and cannot eject it, turn ACC of your
car off once and turn it on again, then press [<] (Eject).
• Do not insert foreign matter into the disc slot.
Random Play
All the available songs (tracks/files) are played in a random
sequence.
Pause
Press [4] (RANDOM).
Press [BAND] (1;).
Press again to cancel.
Press again to cancel.
Folder Random Play (MP3/WMA/AAC)
All the available files in current folder are played in a random
sequence.
Hold down [4] (RANDOM) for more than
2 seconds.
Hold down again to cancel.
Repeat Play
The current song (track/file) is repeated.
Press [6] (REPEAT).
Press again to cancel.
Function Settings
[VOL]
selects a value in the function menu.
(PUSH SEL) (Push to select)
selects items in the function menu.
[DISP] (Display)
exits from the function menu.
1
Hold down [VOL] (PUSH SEL) for 2 sec. or more to open the function menu.
Note: If no operation takes place for more than 5 seconds in function setting, the display returns to the regular mode.
2
3
Press [VOL] (PUSH SEL) to select a mode to
Turn [VOL] clockwise or counterclockwise to
Turn [VOL] clockwise or counterclockwise to
be adjusted.
adjust.
adjust.
Demonstration
1: Up
2: Down
You can set up the monitor to display or hide the
demonstration screen.
Note: Button operation with either the main unit or
1: Increased
remote control allows users to cancel the demonstration
2: Decreased
screen for 20 seconds and enable the selected operation
even in the demo-on mode.
1: Increased
Mute/Attenuation
2: Decreased
You can select mute or attenuation.
1/2: center frequency up/down
[:] [9]: Band selection
[] []: Level up/down
AUX1 Skip
\CQ-RX420U\
If AUX1 is not used, the AUX1 mode is skipped when
1: Right enhanced
selecting the source.
2: Left enhanced
1: Front enhanced
\CQ-RX320L\
AUX Skip
2: Rear enhanced
\CQ-RX120U\ \CQ-RX120L\
"General")
If AUX is not used, the AUX mode is skipped when
selecting the source.
Notes:
• To return to the regular mode, press [DISP].
\CQ-RX420U\
• The sequence and contents of setting items may depend on the conditions of devices to be connected. For further information,
refer to the System Upgrade Guidebook or the instruction manuals for the devices to be connected.
Troubleshooting
If You Suspect Something Wrong
Warning
Check and take steps as described below.
• Do not use the unit in an irregular condition, for example,
If the described suggestions do not solve the problem, it is
without sound, or with smoke or a foul smell, which can cause
recommended to take the unit to your nearest authorized Service
Disc Player (MP3/WMA/AAC
ignition or electric shock. Immediately stop using the unit and
Center. The product should be serviced only by qualified personnel.
disc):
consult your dealer.
Please refer the checking and the repair to professionals. Panasonic
• Never try to repair the unit by yourself because it is dangerous
Normal
Normal
shall not be liable for any accidents arising out of neglect of checking
to do so.
the unit or your own repair after your checking.
Disc title
Play time
Never take measures especially those other than
indicated by italic letters in "Possible Solution" described
below because those are too dangerous for users to
Track title
Folder name/
Album*
handle themselves.
Clock
File name/
Trouble
Possible Solution
Trouble
Title, artist*
Common
Radio
Clock
•
Start the engine. (Or turn the ignition
•
switch to the ACC position.)
*ID3/WMA/AAC Tag On/Off
Frequent noise
•
•
Verify the wiring. (battery lead, power
Hold down [3] for more than
lead, ground lead, etc.)
No power
2 seconds.
•
Fuse blown (Contact the nearest Service
•
Center.)
Preset data
album title and song title/
•
Ask a professional for fuse replacement.
deleted
artist name are displayed.
•
Be sure to use the same rated fuse.
(Default)
•
Disable the mute function.
folder name/file name are
•
Verify the wiring.
Error Display Messages (Disc Player)
No sound
displayed.
•
Wait until the dew disappears before
turning on the unit.
(The disc is ejected automatically.)
The disc is dirty or upside down.
•
Make sure that grounding is established
•
Noise
properly.
(The disc is ejected automatically.)
No sound from
•
Adjust the balance and fader.
The disc has scratches.
left, right, front,
•
Verify the wiring.
•
or rear speaker
No operation by some cause.
Folder Repeat Play (MP3/WMA/AAC)
Left and right
•
Connect the speaker lead correctly.
•
The current folder is repeated.
sounds are
Hold down [6] (REPEAT) for more than
reversed
2 seconds.
Cannot read the file
Hold down again to cancel.
•
Disc Player
Scan Play
WMA/AAC file can be copyrighted.
No sound,
•
Load the disc correctly.
•
•
Clean the disc.
The first 10 seconds of each songs (tracks/files) is played in
or disc is
sequence.
automatically
Press [5] (SCAN).
ejected
\CQ-RX420U\
Press again to cancel.
Note: Refer to the System Upgrade Guidebook for error messages
Sound skip,
•
Clean the disc.
regarding optional products.
poor sound
Folder Scan Play (MP3/WMA/AAC)
\CQ-RX320L\
quality
Note: Refer to the Operating Instructions USB for error messages
From the next folder, the first 10 seconds of the first file in
regarding optional products.
•
The maximum permissible tilt angle is
each folder is played in sequence.
Sound skip due
30°.
Hold down [5] (SCAN) for more than
to vibration
•
Secure the unit.
2 seconds.
Hold down again to cancel.
•
Press [<]. If the disc is still not ejected,
Disc not
contact the nearest Service Center.
ejectable
Sound Control
You have 6 preset modes (FLAT, ROCK, POP, VOCAL, JAZZ,
CLUB). You can customize your settings for these and save
(FLAT) flat frequency response:
them for instant recall.
does not emphasize any part. (Default)
SQ Changeover
(ROCK) speedy and heavy sound:
1 Press [SQ] to activate the SQ selection mode.
exaggerates bass and treble.
2 Press [SQ] to select the sound type as follows.
Press [DISP] to return to the regular mode.
(POP) wide-ranged and deep sound:
slightly emphasizes bass and treble.
Notes:
• After pressing [SQ] on the main unit, you can also select a
(VOCAL) clear sound:
sound type by pressing the preset buttons [1] to [6].
emphasizes middle tone and slightly emphasizes treble.
• Please refer to "Audio Settings" for the adjustment to each
speaker.
(JAZZ) jazz-specific deep sound:
sound with emphasis on sharpness of high-hat and echo
saxophone.
1: On (Default)
(CLUB) club and disco-specific sound:
reproduction of realism being in a club.
2: Off
You can adjust the characteristics of the currently selected
1
Press [VOL] (PUSH SEL:
sound type (SQ). (
Above)
Select) to open the audio
It is also possible to preset up to 5 different adjusted SQs.
1: Volume down
menu.
2
by 10 steps
Press [VOL] (PUSH SEL: Select) to
SQ3 (3-Band Sound Quality)
select SQ SET.
Center frequency and level are adjustable in each of 3 bands.
3
This lets you fine-tune sound quality for each genre to suit
Adjust each band.
2: Volume off
car-interior acoustics and your personal preferences.
1/2: center frequency up/down
(Default)
Tone/SQ adjustable range: 12 dB to 12 dB (by 2 dB)
[:] [9]: Band selection
SQ Low/Bass:
±12 dB (at 60 Hz, 80 Hz, 100 Hz, 200 Hz)
[] []: Level up/down
1: On (Skip
SQ Mid:
±12 dB (at 500 Hz, 1 kHz, 2 kHz, 3 kHz)
disabled.) (Default)
SQ High/Treble: ±12 dB (at 10 kHz, 12 kHz, 15 kHz, 18 kHz)
Level
Frequency
• The bass/treble control level of each frequency is fixed to
the frequency that has been selected for SQ.
4
Hold down the numeric button [2] to [6]
2: Off (Skip
for 2 sec. or more.
To return an adjusted SQ to the default setting
enabled.)
1 Press [SQ], and select the SQ which is to be returned to
• The adjusted SQ is preset in the number of the selected
the default setting. (Only for main unit)
button, and return to the regular mode resumes.
1: On (Skip
2 Hold down [BAND] for 2 sec. or more.
• When you suspend the SQ preset adjustment, each level
disabled.) (Default)
remains your recent adjustment until a new SQ presetting
Notes:
operation is performed or you call up the SQ preset.
• You cannot save any SQ presetting value in [1] button.
• Any SQ adjustments will not change the call up screen
names such as ROCK and JAZZ.
2: Off (Skip
• Do not activate SQ and Bass/Treble at the same time to
enabled.)
avoid causing sound distortion.
Memorandum
Possible Solution
Tune in to another station of high-intensity
waves.
Make sure that the antenna mounted point
is grounded properly.
The preset memory is cleared to return
to the original factory setting when
the power connector or battery is
disconnected.
Check the disc.
Check the disc.
If normal operation is not restored,
consult your dealer or the nearest
Service Center to ask for repairs.
Check the disc.
The file protected by copyright is not
playable.
Advertisement
