HT-CT770
MAIN BOARD IC2009 ADSST-AVR-3045 (DSP)
Pin No.
Pin Name
1
VDD_INT
2
CLK_CFG1
3
BOOT_CFG0
4
VDD_EXT
5
VDD_INT
6
BOOT_CFG1
7
GND
8, 9
NC
10
CLK_CFG0
11
VDD_INT
12
CLKIN
13
XTAL
14
VDD_EXT
15, 16
VDD_INT
RESETOUT/
17
RUNRSTIN
18
VDD_INT
19
MOSI
20
MISO
21
SPICLK
22
VDD_INT
23
DPI_P05
24
DSP_CS
25
MD
26
VDD_EXT
27
DPI_P08
28
RESET_MAIN
29
VDD_INT
30
UART_OUT
31
UART_IN
32
LED
33
DPI_P12
34
DPI_P13
35
DAI_P03
36
DPI_P14
37 to 39
VDD_INT
40
SL/SR_IN
41
SL/SR_OUT
42
BCLK_IN
OPTION_L/
43
OPTION_R_OUT
44
FRONTHI_L/R_OUT
45
VDD_INT
46
VDD_EXT
47
VDD_INT
48
L/R_OUT
49
MID/SW2_OUT
50
SBL/SBR_OUT
51
ZONE_L/R
52
VDD_INT
53
VDD_EXT
54
MCLK_IN
55
VDD_INT
56
C/SW1_OUT
57
A/D_2CH
58
C/SW_IN
59
LRCLK_IN
56
I/O
-
Power supply terminal (+1.1V) (for core)
Core instruction rate to CLKIN (pin 12) ratio selection signal input terminal
I
Fixed at "L" in this unit
I
Boot mode selection signal input terminal
-
Power supply terminal (+3.3V) (for I/O)
-
Power supply terminal (+1.1V) (for core)
I
Serial data input from the system controller
-
Ground terminal
-
Not used
Core instruction rate to CLKIN (pin 12) ratio selection signal input terminal
I
Fixed at "L" in this unit
-
Power supply terminal (+1.1V) (for core)
I
System clock input terminal (25 MHz)
O
System clock output terminal (25 MHz)
-
Power supply terminal (+3.3V) (for I/O)
-
Power supply terminal (+1.1V) (for core)
I/O
Reset signal output and running reset signal input terminal
-
Power supply terminal (+1.1V) (for core)
I
Serial data input from the system controller
O
Serial data output to the system controller
I
Serial data transfer clock signal input from the system controller
-
Power supply terminal (+1.1V) (for core)
I
Chip select signal input from the system controller
I
Chip select signal input from the system controller
-
Not used
-
Power supply terminal (+3.3V) (for I/O)
-
Not used
-
Not used
-
Power supply terminal (+1.1V) (for core)
O
Serial data output to the system controller
I
Serial data input from the system controller
-
Not used
-
Not used
-
Not used
-
Not used
-
Not used
-
Power supply terminal (+1.1V) (for core)
I
Audio signal (for surround L-ch/R-ch) input from the digital audio interface receiver
O
Audio signal output terminal
I
Bit clock signal input from the digital audio interface receiver
O
Audio signal output terminal
O
Audio signal output terminal
-
Power supply terminal (+1.1V) (for core)
-
Power supply terminal (+3.3V) (for I/O)
-
Power supply terminal (+1.1V) (for core)
O
Audio signal (for front L-ch/R-ch) output to the stream processor
O
Audio signal output terminal
O
Audio signal output terminal
I/O
Not used
-
Power supply terminal (+1.1V) (for core)
-
Power supply terminal (+3.3V) (for I/O)
I
Master clock signal input from the digital audio interface receiver
-
Power supply terminal (+1.1V) (for core)
O
Audio signal (for subwoofer) output to the stream processor and RF modulator
I
Audio signal input from the digital audio interface receiver
I
Audio signal (for center and subwoofer) input from the digital audio interface receiver
I
L/R sampling clock signal input from the digital audio interface receiver
Description
Fixed at "H" in this unit
Not used
Not used
Not used
Not used
Not used
Not used