Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Miranda Densite HDA-1861
Summary of Contents for Miranda Densite HDA-1861
- Page 1 DENSITÉ series HDA-1861 Reclocked HD/SD/ASI DA with EQ Guide to Installation and Operation M950-9900-100 15 Mar 2011 Miranda Technologies Inc. 3499 Douglas-B.-Floreani St-Laurent, Québec, Canada H4S 2C6 Tel. 514-333-1772 Fax. 514-333-9828 www.miranda.com © 2011 Miranda Technologies Inc.
-
Page 2: Electromagnetic Compatibility
EN 61000-4-8 Power frequency magnetic field immunity • EN 61000-4-11 Voltage-dips, short-interruptions and voltage variations immunity How to contact us: For technical assistance, please contact the Miranda Technical support centre nearest you: Americas Asia Europe, Middle East, Africa, UK Telephone:... -
Page 3: Table Of Contents
GUIDE TO INSTALLATION AND OPERATION Table of Contents HDA-1861 Reclocked HD/SD/ASI DA with EQ ................. 5 Introduction ............................5 Features .............................. 5 Block Diagram ............................. 5 Front Card-edge Interface ........................6 Installation ..........................7 Installation of Rear Connector Panels ....................7 Card Installation .......................... - Page 4 GUIDE TO INSTALLATION AND OPERATION HDA-1861...
-
Page 5: Hda-1861 Reclocked Hd/Sd/Asi Da With Eq
GUIDE TO INSTALLATION AND OPERATION 1 HDA-1861 Reclocked HD/SD/ASI DA with EQ 1.1 Introduction The HDA-1861 is a reclocked HD/SD distribution amplifier with up to 9 outputs and automatic equalization for up to 140 meters of cable (Belden 1694A). Reclocking of the video signals provides an additional level of signal integrity in long cable length applications. -
Page 6: Front Card-Edge Interface
GUIDE TO INSTALLATION AND OPERATION 1.4 Front Card-edge Interface The front card-edge of the HDA-1861 incorporates two elements: • Status LED (see section 3.1) • Select Button (see section 3.2) HDA-1861 Select Button Status LED Figure 1.2 Front card-edge layout 6 | HDA-1861... -
Page 7: Installation
Miranda Densité-series cards are each associated with a rear connector panel, which must be installed in the Densité frame before the card can be inserted. The HDA-1861 card is sized to fit into Miranda’s Densité-2 frame. Two different rear connector panels are available to fit the Densité 2 frame: •... -
Page 8: Card Installation
2.3 Installing Densité-2 Cards and Rear Modules in a Densité-3 Frame The Densité-3 frame supports many Miranda Densité-2 series cards, including the HDA-1861. Should you wish to install the HDA-1861 card in your Densité-3 frame, you will need an adapter for the card. You may use the 3 RU rear panel that is available for the HDA-1861 (HDA-185N/186N-3SRP), or you may use one of the two 2 RU rear panels. - Page 9 GUIDE TO INSTALLATION AND OPERATION Rear adapters: 3-RU rear module adapters are available for Single and Double Densité-2 rear panels: DENSITE DRP-3RU DENSITE SRP-3RU Install these as follows: 1. Position the adapter at the top of the empty slot(s) on the rear of the frame. 2.
-
Page 10: Signal Connections On Rear Connector Panels
GUIDE TO INSTALLATION AND OPERATION 2.4 Signal Connections on Rear Connector Panels Three rear panels are available for the HDA-1861. HDA-185N/186N-SRP – single-slot-width Densité-2 panel Connections: 1 x HD SDI IN 4 x HD SDI OUT * HDA-185N/186N-SRP – double-slot-width Densité-2 panel Connections: 1 x HD SDI IN 9 x HD SDI OUT * HDA-185N/186N-3SRP –... -
Page 11: Operation
GUIDE TO INSTALLATION AND OPERATION 3 Operation 3.1 Card-Edge Status LED The status monitor LED is located on the front card-edge of the HDA-1861, and is visible through the front access door of the DENSITÉ frame. This multi-color LED indicates the status of the HDA-1861 by color, and by flashing/steady illumination. -
Page 12: Menu For Local Control
GUIDE TO INSTALLATION AND OPERATION The local control panel displays a menu that can be navigated using the four pushbuttons located beneath the display. The functionality of the pushbuttons is as follows: [+] [–] Used for menu navigation and value modification [SELECT] Gives access to the next menu level. - Page 13 GUIDE TO INSTALLATION AND OPERATION CONFIG ALARM menu: For each alarm, select the way in which it will be displayed on the card-edge Status LED. Alarm level: [GREEN, YELLOW, RED, FLASH RED] For each alarm, select whether it will be reported on the GPI output of the frame controller. Alarm report: [NONE, GPI] FACTORY DEFAULT restores the HDA-1861 to the factory set-up conditions, shown underlined in the menu.
-
Page 14: Specifications
GUIDE TO INSTALLATION AND OPERATION Specifications INPUT Signal: HD-SDI SMPTE-292M (1.485, 1.485/1.001 Gbps) SD-SDI SMPTE-259M-C (270 Mbps) EN50 83-9 DVI-ASI (270 Mbps) SMPTE 310M/DVB-SSI Cable length: HD: 140 m Belden 1694A SD: 300 m Belden 1694A Return loss: > 15 dB up to 1.5 GHz OUTPUTS (9) Signal: HD-SDI SMPTE-292M (1.485, 1.485/1.001 Gbps)
Need help?
Do you have a question about the Densite HDA-1861 and is the answer not in the manual?
Questions and answers