Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Anolis ArcPower 72/K2
Summary of Contents for Anolis ArcPower 72/K2
- Page 1 version 1.7...
-
Page 2: Table Of Contents
8.4 Test sequences ......................14 8.5 Stand-alone mode ....................14 8.6 Special functions ...................... 14 9.Control of the ArcPower 72/K2 via RS-232 ..............17 9.1Wiring an RS-3 serial port ..................17 9. Selecting a zone ....................... 17 9.3 Setting a serial port of PC ..................17 9.4 Zone commands ...................... -
Page 3: Safety Instructions
CAUTION! Unplug mains lead before opening the housing! FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START - UP! 1. Safety instructions Every person involved with installation and maintenance of this product has to: - be qualilfied - follow the instructions of this manual CAUTION! Be careful with your operations. -
Page 4: Description Of The Arcpower 72/K2
3.Description of the ArcPower 72/K2 1 - Control board 2 - Power Indicator 3 - DMX Output 4 - DMX Input 5 - LED Zone outputs 6 - RS 3 Output 7 - Fuse Holder 8 - Power Cord DMX Input,Output... -
Page 5: Mounting The Arcpower 7/K
4.2.Mounting the ArcPower 72/K2 The ArcPower 72/K2 should be be placed on a non-f lammable f lat surface in any orientation and fixed by the 4 screws.There are 4 mounting holes of diameter 5 mm in housing of the driver. Ensure that instalation place Screws is enough ventilated. -
Page 6: Installing Instructions
Accidental connection DMX 512 Input/Output to non-DMX 512 device (e.g.Ethernet network Hub) can damage the ArcPower 72/K2. Maximum total cable length between one LED zone output of the Arcpower 72/K2 and all its connected LED modules is 40 metres. Single ArcPower 72/K2 installation:... - Page 7 Multiple ArcPower 72/K2 installation: Connect the DMX output of the first ArcPower 72/K2 with the DMX input of the next ArcPower 72/K2. Always connect one output with the input of the next ArcPower 72/K2 until all fixtures are connected.In this way,up to 32 fixtures can be chained together.
-
Page 8: Master-Slave Operating
5.2.Master-slave operating 1.Unplug from the mains before installation. 2.Connect the LED modules to the fixtures. 3.Connect the DMX output of the master fixture in the data-chain with the DMX input of the first slave. Always connect output with the input of the next slave until all slaves are connected.Up to 32 fixtures can be connected in master/slave chain 4.Insert the termination plug (with 120 Ohm) into DMX input of the master fixture and into the DMX output of the last slave fixture in the link in order to ensure proper transmission on the data link. -
Page 9: Operating Via Dynet Protocol
5.3. Operating via DyNet protocol 1.Unplug from the mains before installation. .Connect LED modules to the fixtures. Connect first fixture to the control panel which suports DyNet protocol. 3.Connect the DMX output of the first fixture in a data link with the DMX input of the second fixture. Always connect output with the input of the next fixture until all fixtures are connected.Up to 3 fixtures can be con- nected in data chain. -
Page 10: Arcpower 72/K2 - Control Menu Map
6.ArcPower 72/K2 - Control menu map Default settings=Bold print 001 (001-502) E.P.1 E.P. E.P.3 P.01 P.06 Aut (OFF,On) EdI. E.P.1 E.P. E.P.3 S.01 S.30 rE1 (0-255) MAn. rE1 (0-255) FA.t.(0-255) (0-255) S.tI. (0-255) (0-255) COP. MAC. (0-255) Str. (0-255) diM. (0-255) St.A. -
Page 11: Arcpower 72/K2-Dmx Protocol
7.ArcPower 72/K2-DMX protocol version 2.1 (software version 1.3 and higher) Mode/Channel Value Function Type of control ZONE 1 Red LED 1 0-55 Red LED saturation control (0-100%) proportional Green LED 1 0-55 Green LED saturation control (0-100%) proportional Blue LED 1... -
Page 12: Control Board
See the chapter "Stand-alone mode" for detail description. For DMX mode, it is important to define the starting DMX address from which the ArcPower 72/K2 will respond to the DMX controller Setting the DMX start channel for DMX operating: 1. -
Page 13: Manual Mode
Programming procedure: 1. Enter "EdI." menu . Press [UP] or [DOWN] to select the desired program which you wish to edit and press [ENTER]. 3. Press [UP] or [DOWN] to select the desired program step ("S.01" - "S.30") and press [ENTER]. 4. -
Page 14: Test Sequences
--- Balance.Select this function to enable (On) or disable (OFF) the white balance which is set in "White colour balance" menu below.If this function is set OFF,ArcPower 72/K2 will use maximum value (255) of satu- ration for red, green and blue channel. - Page 15 [ENTER] to confirm selection. i.bL. --- Initial blink.If this function is on,ArcPower 72/K2 makes auto-calibration (All LEDs light on 100% for short time) after switching it on.If this function is set off,you have to set manually every colour on max.bright- ness after switching on the driver before starting regular operating.This action should last min.
- Page 16 To update software in the fixture: 1.Installation of DMX Software Uploader: 1.DMX Software Uploader program is available from the ANOLIS web site at WWW.anolis.cz. 2.Make a new directory ( e.g. ANOLIS_Uploader) on your hard disk and download the software to it.
-
Page 17: Control Of The Arcpower 72/K2 Via Rs-232
9.Control of the ArcPower 72/K2 via RS-232 9.1Wiring an RS-232 serial port 9-pin D connector (male) Front view of the socket: Pin 1: Not connected Pin : Received Data Pin 3: Transmitted Data Pin 4: Pin 5: Signal Ground Pin 6:... - Page 18 zone Z blue; zone Z white; zone Z yellow; zone Z cyan; zone Z magenta; zone Z blackout; Z ...means number of the zone (0-9) red/green/blue/white/yellow/cyan/magenta..determines colour blackout..closes light output ;.....means end of character sequence Examples: zone 3 green; zone 0 blackout; Type 2: Colour mixing-RGB The syntax of the command is: zone Z r,g,b;...
-
Page 19: Technical Specifications
10.Technical Specifications: Power supply: Input Voltage: 100-40 V AC, 50/60 Hz Fuse:T 3.15 A H Max.Pover Consumption:40VA Input: Control:DMX 51 or DyNet protocol DMX connection:RJ45 RS 3 connection:9-pin D connector Output: Max.Output Voltage:48V DC Max.Output current:700 mA per colour Max.load per zone : 36x K LED´s in RGB mode, 4x K LED´s in RGBW mode Total load :7xK LED´s in RGB mode 84xK LED´s in RGBW mode Maximum total cable length between one LED zone output and all its connected LED modules:... -
Page 20: Replacing The Fuse
Adaptor RJ45/DMX 5 pin..No.13050731 11. Replacing the fuse 1.Before replacing the fuse, unplug mains lead! 2.Unscrew the fuse holder on the rear side of the ArcPower 72/K2 with a fitting screwdriver from the housing (anti-clockwise). 3.Remove the old fuse from the fuse holder.
Need help?
Do you have a question about the ArcPower 72/K2 and is the answer not in the manual?
Questions and answers