Advertisement
Advertisement
Table of Contents
Related Manuals for Trusted Clean Dura 18
Summary of Contents for Trusted Clean Dura 18
- Page 1 Trusted Clean Dura 18 Electric Auto Scrubber DURA 18 REV.01(06-12) 80189...
- Page 2 CONGRATULATIONS on your purchase of our product, and welcome to the family. We appreciate your business and will do everything in our power to keep you happy with your purchase for many years to come. As part of the family, you are entitled to the best protection by one of the most comprehensive warranties in the industry.
- Page 3 SAFETY PRECAUTIONS This machine is intended for commercial use. It is constructed for use in an indoor environment and : Flammable materials can cause an is not intended for any other use. Use only with explosion or fire. Do not use flammable materials recommended accessories.
-
Page 4: Installing Pad Driver Or Brush
the squeegee bracket. (the wheels on the squeegee point to the back) 2. Tighten the knobs securely. MACHINE SET UP & INSTALLATION UNPACK MACHINE FILLING THE SOLUTION TANK Be sure and check packing carton for any damage. Immediately report any damage to carrier. Be 1. -
Page 5: While Operating Machine
Adjust solution flow by adjusting the position 1. Remove the drain hose from the holder, and of ball valve knob. place the drain hose over the floor drain. Twist off the drain hose plug to begin the draining process. WHILE OPERATING MACHINE 2. -
Page 6: Vacuum Motor Maintenance
it down with a damp towel. Be sure to store the squeegee in the up position. 4. Remove the float shut-off assembly and rinse it out with clean water. 5. Clean machine with an approved cleaner and a damp towel. Don’t spray water to clean the outside of machine to avoid damage to motor and wiring. - Page 7 BASIC TROUBLESHOUTING PROBLEM CAUSE SOLUTION The wiring not connected correctly or Check the wiring or contact the distributor you purchased the machine from bad wiring No Power Bad brush motor Contact the distributor you purchased the machine from Carbon brushes worn out Contact the distributor you purchased the machine from Check the wiring or contact the distributor you The wiring not connected correctly or...
-
Page 8: Technical Specifications
Technical Specifications: 18” 30” Efficiency 18,000 ft²/ hr. . a i 18” 255 RPM 65 lbs. 110-115V, 750W, 1 HP 110-115V, 650W 8 gallons 11 gallons 150 lbs. 43” 38” 21.5” 82” Semi-Automatization 70 dB 65” (water lift) - Page 10 PART DESCRIPTION NUMBER REQ'D VF80111 FILTER, CLEAR DOME VF82139 “O” RING VF80113 FILTER VV20501 SCREW, PH, SST, M5 X 14 VV13654 WASHER, SST, M5 VF80112 MOUNTING BASE, FILTER VF82090 CLAMP, HOSE VF80349 HOSE, INLET, FILTER VF13521 NUT, M6 VF13533 WASHER, M6 VV13607 WASHER, LOCK, M6 VF13495...
- Page 11 PART DESCRIPTION NUMBER REQ'D BARB, HOSE, 90° DEG VF81403 VF14255 SET SCREW, M12 X 65 VF80262 VF80262 SPRING WIRE SPRING WIRE VF80219 SHAFT, DRIVEN PULLEY GT13015 SCREW, HEX SOCKET, M6 X 30 VF14400 SCREW, ST, M4.2 X 13 VF13502 NUT, NYLON INSERT, M6 VF14225A SCREW, FH, M6 X 40 VF13535...
- Page 13 PART DESCRIPTION NUMBER REQ'D VF82010 CLEAR COVER,RECOVERY TANK VF82010B GASKET,CLEAR DOME VA13483 WASHER, PLAIN, M4 VA13477 SCREW, ST, M4.2 X 16 VF80343A MODEL DECAL, RIGHT LOGO ZD55000A VACUUM MOTOR, 110V VF80357 HEAT RESISTANCE COVER VF13533 WASHER, PLAIN, M6 VF13502 NUT, NYLON INSERT, M6 VF13514A WASHER, PLAIN, M8 VF82013...
- Page 15 PART DESCRIPTION NUMBER REQ'D VF81408 ADJUSTING PLATE VF13535 WASHER, PLAIN, M8 VF13519 WASHER, LOCK, M8 VV13604 BOLT, M8 X 20 VF81710 ADJUSTING SCREW VF80322 PIN, HANDLE LOCK VF80323 TUBE, HANDLE ADJUSTMENT VF81716 SPRING VF80317BD LEVER, SWITCH, LEFT VV13650 SCREW, PH, M4 X 10 VF81712 SPRING VV13652...
- Page 17 PART PART DESCRIPTION NUMBER REQ'D VF81222 SCREW, HEX SOCKET, SHOULDER, 5/16 X 1.25" " VF13535 WASHER, PLAIN, M8 X M20 X 2 VV20203 NUT, NYLON INSERT, 5/16" VF82121 VF82121 KNOB, M6 KNOB, M6 VF82118 BACK UP STRIP, SQUEEGEE, FRONT VF82062 BLADE, SQUEEGEE, FRONT "...
Need help?
Do you have a question about the Dura 18 and is the answer not in the manual?
Questions and answers