Only use the recommended power cable for powering the Nextiva S5000 IP cameras. ● Turn off the Nextiva S5000 IP cameras as soon as smoke or unusual odors are detected. ● Keep the Nextiva S5000BX and FD models away from water. If they become wet, turn off immediately.
Preface The Nextiva® S5000 IP Camera User Guide presents information and procedures on installing, configuring, and using the IP camera. Audience This guide has been prepared for the following audience: ● IT system administrators ● Network administrators ● Engineers ●...
5678 (Monday to Singapore: +65-68266099 Thursday); 9:00 am to 5:30 pm (Friday) Related Documentation ● Nextiva S5000BX Quick Installation Guide ● Nextiva S5000FD Quick Installation Guide ● Nextiva S5000FDW Quick Installation Guide ● Sconfigurator User Guide ● Nextiva VMS 6.1 Administration Guide ●...
Page 10
Preface Send your questions or comments on the current document, or any other Nextiva user documentation, to our documentation feedback team at documentationfeedback@verint.com. Verint Video Intelligence Solutions viii...
Summary of Changes This section lists technical updates and new material added to the Nextiva S5000 IP Camera User Guide. Revision 5- February 2013 Update to the copyright page. Revision 4 - October 2011 ● New supported resolutions (2CIF and 4CIF) for the Nextiva S5003 model with Nextiva VMS.
Revision 1- May 2010 This is the first edition of the Nextiva S5000 IP Camera User Guide. The Nextiva S5000 IP cameras are compatible with Nextiva Video Management software and the Nextiva EdgeVR network video recorder. Features Nextiva S5000 IP Cameras...
Nextiva S5000 Overview Nextiva S5000 Overview These professional IP cameras feature resolutions from VGA to high-definition 2.0 megapixel to accommodate a wide range of video surveillance requirements. They provide excellent video quality in both day and night conditions, with an IR cut filter that is automatically removed for optimum image clarity in low-light environments or where secondary infrared illumination is used.
802.1X tamper trapping, and support for CS-mount manual or auto-iris lenses. Cameras can be configured using a Verint Web browser interface or Nextiva Control Center, a centralized management portal. All these features make the Nextiva S5000BX day/night IP cameras flexible, scalable, and suitable for virtually any application or environment.
Page 16
Hardware Overview Audio/Video out SD/SDHC Card Status LEDs Microphone External/ NTSC/ Internal 12V DC Power RJ-45 Network Hardware Reset Button Built-in Microphone Light Sensor RS-485 - 12V DC Input Relay Output RS-485 + Dry Contact AC 24V Input Input DC-Iris Control Ground Connector Auto Iris...
Chapter 1: Overview Nextiva S5000FD The Nextiva S5000FD models are ideal for indoor applications in which discreet and attractive surface-mounted cameras are needed. An elegant 3-axis gimbal and a wide varifocal lens facilitate setup at any mounting angle, and an optional recess ceiling adapter to further reduce obtrusiveness.
Hardware Overview Nextiva S5000FDW The Nextiva S5000FDW IP dome outdoor vandal resistant cameras feature resolutions from VGA to high-definition 2.0 megapixel to accommodate a wide range of video surveillance requirements. Dual streaming and supported video compressions from H.264 to MJPEG and MPEG-4 help optimize use of valuable bandwidth and storage.
Chapter 1: Overview Connecting the Camera Digital Input/Digital Output The Nextiva S5000 IP cameras supports digital input and output for connecting the camera to external devices such as motion and sound detectors, smoke detectors and alarm systems. Refer to the following illustration for the connection method.
Understanding the LED Indicators Understanding the LED Indicators The Nextiva S5000BX and S5000FD models have a dual-colored (red-green) LEDs to indicate the current status of the IP camera. The Nextiva S5000FDW models have a single LEDs. Nextiva S5000 IP Camera...
The following settings can be supported simultaneously on the two encoders when streaming in H264 format. Note that the S5000 series can also stream in MJPEG or MPEG4 format. The numbers are not represented. Do not assume any improvements if those codec are used since the S5000 cameras are optimized to stream H264 as well as MJPEG or MPEG4.
Page 22
Frame Rate and Performance www.verint.com/video_solutions...
Package Contents Package Contents Nextiva S5000BX: ● One Nextiva S5000BX IP camera (S5003BX-DN or S5020BX-DN) ● One allen key for SD Card installation and back focus adjustment ● One 3.5mm to BNC analog video cable ● Quick Installation Guide Nextiva S5000FD: ●...
TIP: Before installing the camera, look for a shooting area that best suits your needs. Installing the Nextiva S5000BX Models This section explains how to install the Nextiva S5000BX models. An outdoor enclosure is also available for the Nextiva S5000BX models, see “Installing the Nextiva S5000BX in an Outdoor Enclosure”...
Page 26
Installing the Nextiva S5000 IP Cameras Connecting the Nextiva S5000BX Models The Nextiva S5000BX models can use a 12V DC or 24V AC for power and are Power-over- Ethernet (PoE)-compliant, allowing transmission of power and data via a single Ethernet cable.
This section explains how to install the Nextiva S5000FD models. Multiple mounting accessories are available for the Nextiva S5000FD models. For a list of available accessories and installation procedures, see “Installing Mounting Accessories with the Nextiva S5000FD” on page 101.
Page 28
Installing the Nextiva S5000 IP Cameras Attach the supplied alignment sticker to the surface. 7 inches (18 cm) 7 inches (18 cm) Ceiling Mount Wall Mount NOTE: When placing the alignment sticker to the surface, keep a minimum distance of 7 inches (18 cm) from the wall or ceiling to allow attachment of the cover.
Verint contains two items: an injector and a power cord. The connection procedure may vary if you use another PoE kit; refer to the PoE kit documentation for more information. CAUTION: When assembling the Nextiva S5000FD models, ensure that the wiring does not get pinched when rotating the gimble.
Page 30
POE injector. If you use a POE injector, make sure the DATA port of the injector is properly connected to the ethernet switch. ► To power the Nextiva S5000FD models using a 12V DC power supply: Connect the power supply cable to the camera. Plug the power supply cable to the power outlet.
► To install the Nextiva S5000FDW models on a surface with the bottom base: Remove dome cover from the Nextiva S5000FDW IP camera using the supplied allen key to loosen the three screws. Attach the supplied alignment sticker to the surface.
Page 32
Installing the Nextiva S5000 IP Cameras Align the four holes on each side of the bottom base with the four plastic anchors on the surface. Secure the bottom base to the surface with a screwdriver. Hole A Hole B Hole A...
Page 33
Wall Mount Ceiling Mount ► To install the Nextiva S5000FDW models on the ceiling without a bottom base: Remove dome cover from the Nextiva S5000FDW IP camera using the supplied allen key to loosen the three screws. Verint Video Intelligence Solutions...
Page 34
Installing the Nextiva S5000 IP Cameras Attach the supplied ceiling hole template sticker to the ceiling. Drill three pilot holes through the three circles on the sticker into the ceiling. Hammer the supplied plastic anchors into the holes. Mount the camera into the ceiling and feed the cables through the hole.
Chapter 2: Installing the Nextiva S5000 IP Cameras Connecting the Nextiva S5000FDW Models The Nextiva S5000FDW models use 12V DC or 24V AC for power and are Power-over-Ethernet (PoE)-compliant, allowing transmission of power and data via a single Ethernet cable. The optional PoE kit sold by Verint contains two items: an injector and a power cord.
Page 36
Installing the Nextiva S5000 IP Cameras ► To power the Nextiva S5000FDW models using a 12V DC power supply: Connect the power supply cable to the camera. Plug the power supply cable to the power outlet. ► To power the Nextiva S5000FDW models using a 24V AC power supply: Connect the wires from the power supply cable to the 24V AC.
Page 37
Chapter 2: Installing the Nextiva S5000 IP Cameras ► To connect the Nextiva S5000FDW models to the network: Connect an ethernet cable with the RJ-45 connector on the harness of the IP camera using the RJ45 female to female adapter.
Setting the Video Standard Setting the Video Standard The Nextiva S5000 IP cameras can run in one of two video standards (NTSC or PAL) and you can use different standards when deploying the devices across multiple sites. The two video standards settings are: ●...
To adjust the viewing angle on the Nextiva S5000FD and Nextiva S5000FDW models: Connect the BNC connector to a CCTV test monitor. NOTE: On the Nextiva S5000FD models, first connect the 1/8in (3.5mm) jack from the Video to BNC cable to the A/V out connector.
Page 40
To adjust the zoom factor and focus range: Connect the BNC connector to a CCTV test monitor. NOTE: On the Nextiva S5000FD and Nextiva S5000BX models, first connect the 1/8in (3.5mm) jack from the Video to BNC cable to the A/V out connector.
Page 41
Nextiva S5000BX models Nextiva S5000FD and Nextiva S5000FDW models For the Nextiva S5000FD and Nextiva S5000FDW models, tighten the zoom controller once you have set the zoom level. Loosen the focus controller and adjust the focus range. ∞...
Completing the Installation Completing the Installation Once you have adjusted the lens, you can now reattach the dome covers on the Nextiva S5000FD and Nextiva S5000FDW models. For the Nextiva S5000BX models, you can begin using the IP camera. ►...
Page 43
Chapter 2: Installing the Nextiva S5000 IP Cameras For the Nextiva S5000FD models, tighten the dome screws with the supplied screwdriver. For the Nextiva S5000FDW tighten the dome screws with the Finally, make sure all parts of the camera are securely installed.
Page 44
Completing the Installation www.verint.com/video_solutions...
A device in APIPA mode does not reside on the same subnet as the other devices on the IP network. Therefore, it may not be able to view or be visible by the other devices. All Nextiva edge devices use the following temporary APIPA configuration: ●...
Page 47
Check Detect All Units on LAN. Ensure that the Discovery IP Address is 255.255.255.255; otherwise, click Reset to Broadcast. In the S5000 Authentication section, type the username and password for the Nextiva S5000. NOTE: The default username and password for the Nextiva S5000 is admin.
Page 48
7) In the Host Name box, type a unique name for the IP camera. ■ If the Nextiva S5000 IP camera s in APIPA mode, double-click the device. 1) Click Yes in the Reconfigure unit dialog box asking you if you want to set a new network configuration on the unit.
Page 49
Chapter 3: Configuring the Nextiva S5000 IP Cameras 2) In the IP Address box, type the IP address for the IP camera. 3) In the Subnet Mask box, type the address specifying in which subnet the IP address of the device belongs.
► To launch the home page from a web browser: In a web browser, type the IP address of the Nextiva S5000 in the Address bar, and then press ENTER to view the live video. NOTE: If you are using Microsoft Internet Explorer, the first time you connect to the Nextiva S5000 IP cameras, an information bar is displayed requiring you to install the RTSPVAPgDecNew2.cab from Verint Systems Inc.
Viewer privileges do not have access to the Configuration page. ► To update a user account: In a web browser, type the IP address of the Nextiva S5000 in the Address bar, and then press ENTER. From the Home page, click Configuration.
Page 52
Click Update to update the user account. ► To set the Operator and Viewer privileges: In a web browser, type the IP address of the Nextiva S5000 in the Address bar, and then press ENTER. Type the username and password.
Page 53
NOTE: Administrators can add up to 20 user accounts. ► To delete a user account: In a web browser, type the IP address of the Nextiva S5000 in the Address bar, and then press ENTER. From the Home page, click Configuration.
Auto Gain Control (AGC). ► To configure the image settings: In a web browser, type the IP address of the Nextiva S5000 IP Camera in the Address bar, and then press ENTER. Type the username and password. From the Home page, click Configuration.
Page 55
Auto: (Default value) The Nextiva S5000 IP camera automatically adjusts the color temperature of the light in response to different light source. Keep current value: The Nextiva S5000 IP camera uses the value according to the following procedure. Select Auto and click Save.
► To configure the normal sensor settings: In a web browser, type the IP address of the Nextiva S5000 IP Camera in the Address bar, and then press ENTER. Type the username and password.
Page 57
12. Click Close to exit the Sensor Settings page. ► To configure the second sensor settings: In a web browser, type the IP address of the Nextiva S5000 IP Camera in the Address bar, and then press ENTER. Type the username and password.
Page 58
Configuring Sensor Settings From the Video Settings section, click Sensor Settings to open the Sensor Settings page. www.verint.com/video_solutions...
Page 59
Chapter 3: Configuring the Nextiva S5000 IP Cameras Click Profile to open the Sensor Settings page for the second profile. Select Enable this profile. Select a mode. ■ Day Mode: Select this option if you want to apply the exposure settings during the day.
Page 60
Configuring Sensor Settings From the Maximum Exposure Time list, select an exposure time (in seconds) according to the light source of the surrounding area. Select from: 1/120, 1/60, 1/30, 1/15, and 1/5. NOTE: Shorter exposure times result in less light. 10.
SDHC memory card as well as view the recording. ► To format the SD/SDHC memory card: In a web browser, type the IP address of the Nextiva S5000 in the Address bar, and then press ENTER. From the Home page, click Configuration.
Page 62
Click Save. ► To search for recordings on the SD/SDHC memory card: In a web browser, type the IP address of the Nextiva S5000 in the Address bar, and then press ENTER. From the Home page, click Configuration. Click Local storage to view the Local storage page.
Page 63
Chapter 3: Configuring the Nextiva S5000 IP Cameras Click Search to display the results in the Search Results window. Once the search results are displayed, you can perform the following: ● Select a result and click View to play the video in a media dialog box.
Certificate Authority which can be validated by a RADIUS server. ► To create a certificate request: In a web browser, type the IP address of the Nextiva S5000 IP Camera in the Address bar, and then press ENTER. Type the username and password.
Page 65
14. Click Save to generate an encoded certificate request. 15. Send the encoded certificate request to a certificate authority, who will then issue a digital certificate that you can then upload to the Nextiva S5000 IP Camera. Verint Video Intelligence Solutions...
Certificate Authority (CA) that they both trust. ► To enable IEEE 802.1x support and select an EAP method: In a web browser, type the IP address of the Nextiva S5000 IP Camera in the Address bar, and then press ENTER. Type the username and password.
Chapter 3: Configuring the Nextiva S5000 IP Cameras Updating the Firmware You can use SConfigurator or a video management software to update the firmware of the Nextiva S5000 IP cameras when a new version becomes available. Updating the firmware allows you access to new features for the IP cameras while retaining its configuration.
Adding the Nextiva S5000 to Nextiva VMS To add the S5000 to Nextiva VMS 6.1, you need to install Nextiva 6.1 Rollup 4 that provides the S5000 adaptor to the system. Use the following procedure to add the S5000 adaptor to Nextiva VMS.
Page 71
Chapter 4: Configuring the Nextiva S5000 with Nextiva VMS information on using Nextiva Control Center, refer to the Nextiva VMS 6.1 Administrator Guide. Verint Video Intelligence Solutions...
Adding the IP Camera with the System Setup Wizard Once the camera is fully discovered, run the System Setup Wizard to add the camera in Nextiva Control Center. At the same time, assign the camera to the applicable Physical and Logical Groups.
Chapter 4: Configuring the Nextiva S5000 with Nextiva VMS Configuring the Nextiva S5020 Video Mode After adding the S5000 to Nextiva VMS, you need to define the video mode. The Nextiva S5020 models supports three video modes: ● 1600 × 1200 Full sensor ●...
You can create as many video profiles and recording profiles as required. For example, you can create a video profile that uses one of the higher resolutions for the Nextiva S5000 IP camera and add this to a new recording profile.
Assigning the Camera to a Recording Profile When a new camera is discovered in Nextiva VMS, it is automatically assigned to the Default Recording Profile. Use this procedure to assign it to a different recording profile. To handle different recording scenarios, you can assign the camera to a different Recording Profile with a different Video Profile, or create new profiles.
Groups are displayed in the Logical View of the Devices workspace and in the Camera Tree in Nextiva Review. These parameters apply to the camera regardless of whether it is assigned to multiple groups or whether it is moved to another group. For more details, refer to the Nextiva VMS Administrator Guide. Configuring the Image Quality Click the Image Quality tab from the Logical View to adjust the brightness of the video image for the selected camera.
You need to click the Refresh button to view changes and fluctuations if you are keeping the Video window open. Click Apply. For further details on Preferred Video Compression and Video Profiles, refer to the Nextiva VMS Administrator Guide. Adjusting the Advanced Properties The Advanced tab provides further information on the Logical settings of the camera.
Page 78
Customizing the Nextiva S5000 Click the Advanced tab. Expand Video Input and adjust each setting accordingly: ■ Auto Iris Choose between Automatic or Manual. ■ Auto White Balance Choose between Automatic or Manual to adjust the color temperature of the light. The default value is Auto.
Page 79
Chapter 4: Configuring the Nextiva S5000 with Nextiva VMS Enables the filter at all times to block infra-red light from reaching the sensor. ● Night Disables the filter at all times to enable infra-red light to reach the sensor. ●...
You need to assign user rights to the Nextiva S5000 IP camera. In Nextiva Control Center, user rights are assigned by group. By default, only the Administrators group has access to the camera. You need to assign access rights to the Nextiva S5000 IP cameras so that they can be controlled by users.
You can configure the camera in Virtual Matrix, so that it can be added to Camera Tour that is played in Nextiva Review. For details on Nextiva Virtual Matrix, refer to the Nextiva Administrator Guide or Help files. Verint Video Intelligence Solutions...
You can create a Nextiva Event Manager to generate an automatic response, such as sending an e-mail or internal notice, or an alarm, if a Nextiva S5000 IP camera loses network connection. For details on Nextiva Event Manager, refer to the Nextiva VMS Administrator Guide or Help files.
Chapter 4: Configuring the Nextiva S5000 with Nextiva VMS Nextiva Resolution Matrix The following table lists the supported resolution for the Nextiva S5020 models when using the 1600 × 1200 Full sensor option: Nextiva Resolutions Nextiva S5020 Supported Resolutions NTSC QCIF 176 ×...
Page 84
2560 × 1600 800 × 600 QSXGA 2560 × 2048 800 × 600 The following table lists the supported resolution for the Nextiva S5020 models when using the 1280 × 720 Cropped option: Nextiva Resolutions Nextiva S5020 Supported Resolutions NTSC QCIF 176 ×...
The following topics are discussed: Using the Nextiva S5000 with the Nextiva EdgeVR ......76 Creating a Secure Connection between the EdgeVR and the Nextiva S5000 Camera .78...
Using the Nextiva S5000 with the Nextiva EdgeVR The Nextiva EdgeVR is an IP Recorder with options to integrate existing analog devices. Because native IP and analog video devices can be integrated on a single platform, customers can use the Nextiva EdgeVR to migrate their video infrastructure from analog to IP at their chosen speed, thereby avoiding expensive hardware upgrades.
Page 89
NOTE: The default port number is automatically set when you select a camera from the Type list. If your network is using another port for an unsecure connection, enter the port number. You will also need to update the TCP/IP Settings for the Nextiva S5000 IP Camera to match the port number entered here.
If you are using the defaults port values, use the following procedure to set up a secure connection. NOTE: You do not need to change the port number in Vid-Center if the Nextiva S5000 is using the default port value.
Creating a Secure Connection Using the Custom Port Values If your network is using port values other than the default values for unsecure and secure connections, then you need to set up the Nextiva S5000 with the values used by your network. Verint Video Intelligence Solutions...
Page 92
Creating a Secure Connection between the EdgeVR and the Nextiva S5000 ► Use the following procedure to set the port values used by your network: In a web browser, type the IP address of the Nextiva S5000 in the Address bar, and then press ENTER. Type the username and password.
Nextiva Vid-Center 4.3 User Guide. With the Nextiva S5000 IP camera, you can create up to three motion detection areas (also referred to as windows). Movement in the areas outside the windows will be ignored. These motion detection windows can be moved, resized, or deleted at any time.
Page 94
A green layer is displayed over the selected areas. NOTE: You can create a maximum of three motion detection areas for an Nextiva S5000 IP camera. Select the region, and for the following two settings, move the slider left or right: ■...
Nextiva S5000BX Technical Specifications Nextiva S5000BX Technical Specifications The following table presents the technical specifications for the Nextiva S5003BX-DN and S5020BX-DN models: Nextiva S5003BX-DN Nextiva S5020BX-DN Video Imaging Device 1/4” CMOS sensor 1/3” CMOS sensor Picture Elements 640(W) x 480(H)
Page 97
3.1W x 3.1H in. (175L x 90W x 90H mm) — does not include length of lens Management Configuration Nextiva, SConfigurator, or Internet Explorer 6.0 Firmware Upgrade Flash memory for upgrade of application firmware over the network Certification and Regulation...
Nextiva S5000FD Technical Specification Nextiva S5000FD Technical Specification The following table presents the technical specifications for the Nextiva S5003FD and S5020FD- DN models: Nextiva S5003FD Nextiva S5020FD-DN Video Imaging Device 1/4” CMOS sensor 1/3” CMOS sensor Picture Elements 640(W) x 480(H)
Page 99
Discreet indoor dome, surface mount (optional recess ceiling mounting kit available) Enclosure Indoor fixed dome enclosure Management Configuration Nextiva, SConfigurator, or Internet Explorer 6.0 Firmware Upgrade Flash memory for upgrade of application firmware over the network Certification and Regulation FCC Part 15 (Subpart B, Class A) Canada...
Nextiva S5000FDW Technical Specification Nextiva S5000FDW Technical Specification The following table presents the technical specifications for the Nextiva S5003FDW-DN and S5020FDW-DN models: Nextiva S5003FDW-DN Nextiva S5020FDW-DN Video Imaging Device 1/4” CMOS sensor 1/3” CMOS sensor Picture Elements 640(W) x 480(H)
Page 101
Vandal dome, all-weather IP66, surface mount, optional mounting kits available Management Configuration Nextiva, SConfigurator, or Internet Explorer 6.0 Firmware Upgrade Flash memory for upgrade of application firmware over the network Certification and Regulation FCC Part 15 (Subpart B, Class A)
Page 102
Nextiva S5000FDW Technical Specification Nextiva S5003FDW-DN Nextiva S5020FDW-DN PS122 12 VDC Efficiency Level V qualified power supply for S5000 Series PM-S50FDW Pendant mount dome enclosure for outdoor fixed dome S50xxFDW IP cameras PB-S50FDW Pendant mount head junction for outdoor fixed dome S50xxFDW IP...
Page 103
Available Mounting Accessories ......... . .94 Installing the Nextiva S5000BX in an Outdoor Enclosure ......98 Installing Mounting Accessories with the Nextiva S5000FD .
Available Mounting Accessories Available Mounting Accessories Verint provides mounting accessories for the different S5000 IP cameras for customized installation based on your requirements. These accessories are available by contacting your Verint Sales representative Accessories for the S5000FD The following table lists the available indoor mounting accessories that are available for the...
Appendix B: Installing Mounting Accessories Accessories for the S5000BX and S5000FDW The following table lists the available Outdoor and Indoor vandal resistant mounting accessories that are available for the S5000BX and S5000FDW models: Camera Model Installation Type Required Accessories S5000BX Enclosure (Outdoor only) HSG1-O-W S5000FDW...
Available Mounting Accessories Camera Model Installation Type Required Accessories Pendant Mount (Outdoor PB-S50FDW Pendant mount head junction and Indoor Vandal Resistant) PP-S50FDW Pipe Pole Mount (Outdoor and WM-S50FDW Pendant gooseneck bracket kit Indoor Vandal Resistant) PL-S50FDW Pole mount adapter www.verint.com/video_solutions...
Page 107
Appendix B: Installing Mounting Accessories Camera Model Installation Type Required Accessories Corner Mount (Outdoor and WM-S50FDW Pendant gooseneck bracket kit Indoor Vandal Resistant) CR-S50FDW Outdoor corner mount adapter Verint Video Intelligence Solutions...
Page 108
Installing the Nextiva S5000BX in an Outdoor Enclosure Installing the Nextiva S5000BX in an Outdoor Enclosure Use the following procedure to install the Nextiva S5000BX in the outdoor enclosure (HSG1-O-W). ► To install the Nextiva S5000BX models in an outdoor enclosure: Open the outdoor enclosure using the provided allen key.
Page 109
Appendix B: Installing Mounting Accessories Attach the plate to the Nextiva S5000BX with the provided screws using a torque of 5 in-lb (0.56 N-m). Attach the plate to the enclosure Verint Video Intelligence Solutions...
Installing the Nextiva S5000BX in an Outdoor Enclosure Route the cables in the enclosure with the provided grommets. NOTE: Use silicone to seal all holes to ensure that the outdoor enclosure remains waterproof. www.verint.com/video_solutions...
Page 111
Appendix B: Installing Mounting Accessories Installing Mounting Accessories with the Nextiva S5000FD Use the following procedure to install the Nextiva S5000FD with the available mounting accessories. ► To install the Nextiva S5000FD models pendant with a standard pipe: Remove the dome cover from the Nextiva S5000FD using the supplied screwdriver.
Page 112
Installing Mounting Accessories with the Nextiva S5000FD Install the pendant mount kit to the pipe. Connect the cables to the camera and install the camera with the supplied screws using a torque of 5 in-lb (0.56 N-m). Attach the dome cover to the camera...
Appendix B: Installing Mounting Accessories ► To install the Nextiva S5000FD on a wall: Remove the dome cover from the Nextiva S5000FD using the supplied screwdriver. Route the cables through the opening of the wall mount plate. Connect the cables to the Nextiva S5000FD.
Page 114
Installing Mounting Accessories with the Nextiva S5000FD Install the wall mount kit with the supplied screws and nuts using a torque of 5 in-lb (0.56 N- Attach the dome cover to the camera Attach the assembly to the wall. www.verint.com/video_solutions...
Page 115
Appendix B: Installing Mounting Accessories ► To install the Nextiva S5000FD on the ceiling using the recess ceiling mount kit: Remove the dome cover from the Nextiva S5000FD using the supplied screwdriver. Verint Video Intelligence Solutions...
Page 116
Installing Mounting Accessories with the Nextiva S5000FD Remove the hexagonal standoffs in the bottom of the recess kit. Hexagonal Standoffs Attach the recess ceiling mount kit to the Nextiva S5000FD. www.verint.com/video_solutions...
Page 117
Appendix B: Installing Mounting Accessories Turn the adjustment screws counter-clockwise to fold the tabs. Adjustment Screws Tabs Attach the supplied ceiling hole template sticker to the ceiling. Feed the cables through the hole and mount the camera to the ceiling. Verint Video Intelligence Solutions...
Page 118
Installing Mounting Accessories with the Nextiva S5000FD Turn the adjustment screws clockwise to secure the tabs to the ceiling. Rotate the black cover inside the dome to fit the lens shooting direction. www.verint.com/video_solutions...
Page 119
Attach the pendant pipes (PL-S50FDW) to the pendant head (PB-S50FDW). Install the quarter turn adaptor to the pendant pipes (PL-S50FDW). Remove dome cover from the Nextiva S5000FDW IP camera using the supplied torx key to loosen the three screws. Route the cables inside the enclosure (PM-S50FDW).
Page 120
Installing Mounting Accessories with the Nextiva S5000FDW 14. Install two set-screws on the dome enclosure. 15. Pull out the cables and connect the main unit to the quarter turn adaptor in the clockwise direction. www.verint.com/video_solutions...
To install the Nextiva S5000FDW with the dome accessories: Select the type of installation you want to perform: ■ Install the Nextiva S5000FDW in a corner using the corner bracket 1) Place the corner bracket (CR-S50FDW) in the desired location and mark the holes for the screws.
Page 122
4) Attach the gooseneck bracket (WM-S50FDW) to the wall. Attach the quarter turn adaptor to the gooseneck bracket (WM-S50FDW). Remove the dome cover from the Nextiva S5000FDW IP camera using the supplied torx key to loosen the three screws. www.verint.com/video_solutions...
Page 123
Appendix B: Installing Mounting Accessories Route the cables from the camera through the dome enclosure. Place the camera in the dome enclosure and rotate it until the mounting holes are aligned. Secure the camera to the dome enclosure with a Philips screwdriver using the provided three screws.
Page 124
Installing Mounting Accessories with the Nextiva S5000FDW 12. Secure the dome enclosure with the 2 remaining set-screws www.verint.com/video_solutions...
Page 128
For more information, please visit us at www.verint.com/video_solutions Americas: info@verint.com EMEA: marketing.emea@verint.com APAC: marketing.apac@verint.com All other trademarks and product names are the property of their respective owners. The information in this document may be superseded by subsequent documents. Revision 5...