1. Manuals
  2. Brands
  3. Harman Music Group Manuals
  4. Music Pedal
  5. HardWire TR-7
  6. Owner's manual

Harman Music Group HardWire TR-7 TREMOLO/ROTARY Owner's Manual

Digital effect pedal
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TR-7
TREMOLO/ROTARY
®

Advertisement

Table of Contents
loading

Summary of Contents for Harman Music Group HardWire TR-7 TREMOLO/ROTARY

  • Page 1 TR-7 TREMOLO/ROTARY ®...

  • Page 2: Declaration Of Conformity

    DECLARATION OF CONFORMITY Manufacturer’s Name: Harman Music Group Manufacturer’s Address: 8760 S. Sandy Parkway Sandy, Utah 84070, USA declares that the product: Product name: TR-7 Product option: All (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.)
  • Page 3 Warning If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery, and recycling. For your protection, read the following: Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic product free of charge to designated collection facilities or to a retailer (if you Important Safety Instructions...
  • Page 4 WARRANTY: ® We at HardWire are proud of our products and back-up each one with the following warranty: Please register online at hardwirepedals.com within ten days of purchase to validate this warranty. HardWire warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship under normal use and service.
  • Page 5 Congratulations! You have just purchased a HardWire digital effect pedal. ® Unlike many analog pedals, the number of hours digital pedals can be powered with 9-Volt alkaline batteries is limited due to the constant draw which digital signal processors require. Until battery technology advances to meet the requirements of digital pedals, we suggest that a battery be used mainly for demonstration and practice purposes.

  • Page 7: Included Items

    Included Items: • HardWire TR-7 Tremolo/Rotary • HardWire StompLock ™ •...
  • Page 9 What Does This Do? 1. Speed Knob - Controls the LFO speed of the Tremolo/Rotary effect. Turning the knob clockwise increases the speed and turning it counter-clockwise decreases the speed. 2. DC Adapter Jack - Connect (an optional) Harman PS200R power supply to this jack.
  • Page 10 input is needed, this jack must be used. Signals will still be heard at both outputs when only the Input 1 (Mono) jack is connected. Connecting a guitar cable to the Input 1(Mono) jack supplies bat- tery power even though the Indicator LED may not be lit.To pro- long battery life, disconnect all cables from the pedal when not in use.
  • Page 11 ing the battery compartment. (See battery replacement diagram). 9. Indicator LED - This LED indicates when the effect is turned on or off. When battery power is low (approximately 15 minutes before end of life), the Indicator LED begins to dim giving you advanced warning that very shortly you will need to replace the battery.
  • Page 12 Tremolo/Rotary Types Tremolo Basic amplitude modulation effect with a variable waveform selector. Opto Tremolo Tremolo based on an opto isolated tremolo circuit found in vintage Fender amps. ® Bias Tremolo Tremolo based on varying the power tube bias used in vintage Vox amps.
  • Page 13 Modify Knob Controls Type Speed Depth Modify Tremolo Speed Depth Waveform Opto Tremolo Speed Depth Tone Bias Tremolo Speed Intensity Tone Duo Trem Speed Depth Speed 2* Rotary Speed Depth (Pitch) Dry Level UltraVibe Speed Intensity Chorus/Vibrato** VibroPan Speed Depth (Pitch) Phase*** * The Speed 2 control affects the second tremolo speed.

  • Page 14: Amplifier Setup

    Amplifier Setup PS200R (optional)
  • Page 15 Effects Loop Setup AMP RETURN PS200R (optional) AMP SEND Note: If the amp effects loop has a mix control, set the mix to 100% full wet.

  • Page 16: Battery Operation

    Battery Operation In the event that battery power is completely depleted, HardWire pedals ® automatically switch into bypass. This eliminates the need to remove the pedal from your pedal chain if the battery is dead.To replace the battery, do the following: Using the tip of a 1/4”...
  • Page 17 Switch is properly fastened, both release pins are flush with the outer side of the pedal. Foot Switch Pedal Switch 9VDC Battery Foot Switch Release Pin Battery Compartment Foot Switch Spring Release Pin Pedal Chassis...

  • Page 18: Tap Tempo

    Tap Tempo The TR-7 Tremolo/Rotary’s Foot Switch can be used as a Tap Tempo switch for setting the tremolo effect’s modulation speed time during a live performance. To access Tap Tempo, do the following: Press and hold the Pedal Switch for 3 seconds.The effect first will turn on and the Indicator LED lights solid BLUE (NOTE: If the effect was already on, it will first turn off and then back on after 3 seconds).
  • Page 19 Below is a table to show the ratio of tapped tempo and the speed at which the effect should modulate. Type Tap Rate Modulation Rate Tremolo 1 second 4 Hz (4 beats per second) Opto Tremolo 1 second 4 Hz (4 beats per second) Bias Tremolo 1 second 4 Hz (4 beats per second)
  • Page 20 To exit Tap Tempo, press and hold the Foot Switch for 3 seconds until the Indicator LED stops flashing and lights solid BLUE again. Once Tap Tempo mode is exited, the tapped modulation speed remains active until either the Type is changed or the Speed knob is adjusted.
  • Page 21 HardWire Performance Accessories ® The performance accessories make integrating a HardWire pedal into any ® pedal board a snap.The following accessories are included: • Hook-and-loop Pedalboard Pad (designed to attach to the surfaces found on most commercial pedalboards) • Foot Switch Glow Sticker (easily visible on dark stages) •...
  • Page 22 Hook-and-loop Pedalboard Pad To attach the Pedalboard Pad, do the following: Peel off the existing rubber skid pad from the bottom of the pedal. Peel the adhesive protector from the back of the Pedalboard Pad. Apply the Pedalboard Pad to the bottom of the pedal.
  • Page 23 Foot Switch Glow Sticker To attach the Foot Switch Glow Sticker, do the following: Peel the adhesive backing from the Foot Switch Glow Sticker. Apply the Glow Sticker to the top of the Foot Switch.
  • Page 24 StompLock To place the StompLock over the pedal knobs, do the following: Set the knobs to your preferred setting. Gently push the StompLock over the top of the knobs. To remove the StompLock, gently lift one side and then the other.

  • Page 25: Specifications

    Specifications Controls - Speed, Depth, Modify,Type, On/Off Pedal Jacks - Input 1 (Mono), Input 2, Output 1 (Mono), Output 2 Input Impedance - >1 MΩ (stereo), >500 kΩ (mono) - effect on Output Impedance - 1 kΩ - effect on Input Impedance - true hardwire bypass - effect off Output Impedance - true hardwire bypass - effect off Power Supply - 9V Alkaline Dry Battery or...
  • Page 26 Notes:...
  • Page 27 Notes:...
  • Page 28 8760 South Sandy Parkway Sandy, Utah 84070 PH (801) 566-8800 FAX (801) 566-7005 ® HardWire is a trademark of Harman Copyright - Harman Printed in China HardWire TR-7 Owner’s Manual 18-0759V-B Please visit us on the World Wide Web at: www.hardwirepedals.com...

Table of Contents