Bosch EX30 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Bosch Manuals
  4. Thermographic Cameras
  5. EX30
  6. Installation instructions manual

Bosch EX30 Installation Instructions Manual

Infrared imager
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION INSTRUCTION
EX30
Infrared Imager™
MAN-30-06
- 1 -

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EX30 and is the answer not in the manual?

Questions and answers

Summary of Contents for Bosch EX30

  • Page 1 INSTALLATION INSTRUCTION EX30 Infrared Imager™ MAN-30-06 - 1 -...
  • Page 2 IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep this instruction. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with manufacturer instructions. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
  • Page 3 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the power where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
  • Page 4 ® IMPORTANT For best results, please read this Instruction Booklet prior to installing the EX30 Infrared Imager. WARNING ! CSA Certified / UL Listed CLASS 2 power adaptors must be used in order to comply with electrical safety ® surveillance...
  • Page 5 PSU box. 3) Contact BOSCH Service Center for further advice. - 5 -...

  • Page 6: Table Of Contents

    INDEX – EX30 Infrared Imager™ PAGE DESCRIPTION..............7 UNPACKING..............8 PARTS LIST ..............8 ITEMS REQUIRED FOR INSTALLATION....... 8 INITIAL PREPARATIONS ..........9 GUIDELINES ..............9 MOUNTING BRACKET PREPARATION ....10 CABLE / BRACKET INSERTION ......11 MOUNTING BRACKET ATTACHMENT ....12 CAMERA MOUNTING ..........

  • Page 7: Description

    DESCRIPTION The EX30 Infrared Imager consists of an LXR camera and an infrared illuminator. This surveillance system gives optimum performance during daylight conditions and in the pitch black of night. The camera has a “Vari Focal” lens, and is seamlessly switched by a photocell when light conditions change from day to night, ensuring no loss of image quality.

  • Page 8: Unpacking

    Check the parts list and confirm all items have been located. Inspect the equipment thoroughly to ensure nothing was damaged in transit. Contact BOSCH Service Center if a problem is noted, see the rear page of this booklet for contact numbers. PARTS LIST...

  • Page 9: Initial Preparations

    If any adjustment needed, it is advisable to check the camera’s operation before installation. GUIDELINES The installation of the EX30 camera is explained in Sections 1 to 7. It is important that these steps are followed in numerical order.

  • Page 10: Mounting Bracket Preparation

    1. MOUNTING BRACKET PREPARATION EXMB.028 Mounting Bracket SET SCREW • Use the supplied Allen Key to remove the setscrew from the supplied mounting bracket. • Separate the two sections of the mounting bracket. - 10 -...

  • Page 11: Cable / Bracket Insertion

    2. CABLE / BRACKET INSERTION EX30 Camera • Carefully feed the Power/BNC cable through both sections of the mounting bracket. • Make sure the cable is not kinked, chafed, or split during this procedure. - 11 -...

  • Page 12: Mounting Bracket Attachment

    3. MOUNTING BRACKET ATTACHMENT • Attach the Mounting Bracket to the Camera’s Mounting Block using the six bolts supplied with the bracket. • Snug the two halves of the bracket together with the Allen head set screw. • Tighten the setscrew enough so that the camera can be adjusted for angle.

  • Page 13: Camera Mounting

    4. CAMERA MOUNTING Warning: this apparatus must be securely attached to the wall or ceiling in accordance with installation instructions. Failure to follow installation instructions ma results in injury/death. Select a suitable location that protects the camera from accidental damage, tampering and environmental conditions exceeding the specifications of the camera to be mounted.
  • Page 14 • Installation should only be performed by skilled personnel Hardware required: • For ceiling mount: Mounting Bracket, Model EXMB.029, Qty = 1 ¼’’ x 2” Lag Screws, Qty = 1 ¼’’ Washer, Qty = 1 • For wall mount: Mounting Bracket, Model EXMB.028, Qty = 1 ¼’’...
  • Page 15 mounting using the following wood screws secured into a 2x4 stud under ½” drywall: • wood screws with washer, 1/4” lag, dia Ø1/4”, 2” long, 9 TPI, with ½” head • 16” flat washer. Camera has not been evaluated for safety requirements using other mounting kits.

  • Page 16: Camera Lens Adjustments And Selecting The Window

    5. CAMERA LENS ADJUSTMENTS AND SELECTING THE WINDOW For optimum picture quality, the camera lens should be as close as possible to the inside face of the viewing window, without touching. The camera is pre-focused with telephoto setting as factory default. Follow the steps below if any adjustment needed.
  • Page 17 Loosen this setscrew for Focus Adjustment Loosen this setscrew for Telephoto or Wide Angle Adjustment 5.1. Vari Focal and “Auto-Iris” Control Adjustments • Loosen the lens set screws for focus/zoom adjustments. • The setscrew marked N ←→ ∞ is used for image focus.
  • Page 18 Telephoto (Factory standard) Use 40º illumination beam Wide Use 80ºillumination beam Use a Neutral Density filter or Infra-Red Pass filter to cover the lens during focusing to simulate low light conditions on scene for correct 24-hour focusing. For camera with vari- focal lens, the camera should be focused with the lens iris fully opened to simulate the worst possible depth of field.

  • Page 19: Led Array - Power Adjustments

    6. LED ARRAY - POWER ADJUSTMENTS If adjustment is needed, remove the rear cover for access to the LRB. The EX30 needs to be powered-up while making the LED power adjustments. Cover the photocell to turn the LEDs “ON” (850nm LEDs will have a slight red glow).

  • Page 20: Osd Adjustment

    7. OSD ADJUSTMENT Open the back cover of EX30 to access the OSD controls. Enter the OSD menu by pressing the joystick button down. Follow the instructions below to make camera adjustments. - 20 -...

  • Page 21: Osd Menu

    8. OSD MENU - 21 -...
  • Page 22 Note The following default settings should not be changed: Lens = DC; E.Shutter = Auto - 22 -...
  • Page 23 - 23 -...
  • Page 24 - 24 -...
  • Page 25 - 25 -...
  • Page 26 - 26 -...
  • Page 27 - 27 -...
  • Page 28 Note The following default setting should not be changed Day & Night = Auto - 28 -...
  • Page 29 - 29 -...
  • Page 30 - 30 -...
  • Page 31 - 31 -...
  • Page 32 - 32 -...
  • Page 33 - 33 -...
  • Page 34 - 34 -...
  • Page 35 - 35 -...
  • Page 36 - 36 -...
  • Page 37 - 37 -...
  • Page 38 - 38 -...
  • Page 39 - 39 -...

  • Page 40: Camera Re-Assembly

    9. CAMERA RE-ASSEMBLY Make sure all wires are properly connected, all holes are sealed against moisture penetration, and all mounting screws are tight. • Slide the lens foam over the camera lens. Make sure the foam is snug and as close to the faceplate viewing window as possible and the photocell is secure with an unobstructed view.

  • Page 41: Troubleshooting Guide -Camera

    10. TROUBLESHOOTING GUIDE -CAMERA PROBLEM POSSIBLE LIKELY SOLUTION CAUSE No Video 1. Power Check the input Supply: power connections at the terminal block, ensuring no wires are Connections loose. …. The supply range is: 12-28VAC or -Voltage 10.5-40VDC. Range... Measure the voltage at the terminal block.
  • Page 42 Check the video signal. If okay, the problem is with the interconnections. If still no video, contact BOSCH Service Center. See rear page of this manual for contact information. Poor Picture Quality Dim Image Iris closed Increase iris level on...
  • Page 43 connections. Relocate or replace Horizontal the power supply. Ground Scan Lines, Looping on Rolling Up Check the coax cable video cable or Down shield is not touching “ground”, e.g. at the couplings. An electrically isolated circuit board or isolation transformer may be required.
  • Page 44 - 44 -...

  • Page 45: Troubleshooting Guide - Leds

    - Aim the LEDs directly at an IR “ON” sensitive camera, or use a mirror to see the lights through the EX30 camera, or wait for the LEDs to warm up (two minutes). - Cover the photo sensor to activate...

  • Page 46: Mounting Hole - Diagram

    12. MOUNTING HOLE - DIAGRAM • All dimensions expressed in millimeters • 1.59” X 3.38” in inches - 46 -...

  • Page 47: General Specifications

    13. GENERAL SPECIFICATIONS Power Consumption: 36W Max. Maximum Current: 3.0A @12Vdc Input Voltage: 24VAC 12VDC Enclosure (housing): Aluminum casting Viewing Window: Glass 130mm H ( 5.12” ) Dimensions: 134.5mm W ( 5.30” 212mm L ( 8.35” ) Operational Temperatures: C to +50 Weight: 2.2kg (4.9 lbs.) Subject to change without notice.
  • Page 48 Note: - 48 -...
  • Page 49 Asia Pacific: Bosch Security Systems Pte Ltd. 38C Japan Pemimpin Singapore 577 180 Phone: +65 6319 3450 Fax: +65 6319 3499 apr.securitysystems@bosch.com www.boschsecurity.com © Bosch Security Systems., Inc. 2009; Data subject to change with out notice - 49 -...

Table of Contents