Section 5: Diagrams; Circuit Boards Location; Printed Wiring Boards And Schematic Diagrams Information; Reference Information - Sony Trinitron KV-29DRC420 Service Manual

5-1.CIRCUIT BOARDS LOCATION

CH Board
WY Board
HCX
Board
DZ Board
MY Board
BY Board
5-2.PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS INFORMATION
All capacitors are in µF unless otherwise noted. pF : µµF 50WV or
less are not indicated except for electrolytics and tantalums.
All electrolytics are in 50V unless otherwise specifi ed.
All resistors are in ohms. kΩ=1000Ω, MΩ=1000kΩ
Indication of resistance, which does not have one for rating
electrical power, is as follows:
Rating electrical power :
1 1
/ W in resistance, / W and
4 10
: nonfl ammable resistor
: fusible resistor
: internal component
: panel designation and adjustment for repair
: earth ground
: earth-chassis
All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
Readings are taken with a color-bar signal input.
Readings are taken with a 10MΩ digital multimeter.
Voltages are DC with respect to ground unless otherwise noted.
Voltage variations may be noted due to normal production
tolerances.
All voltages are in V.
S : Measurement impossibility.
: B+line.
: B-line. (Actual measured value may be different).
: signal path. (RF)
Circled numbers are waveform references.
KV-27HS420/29DRC420/30HS420/32HS420/34HS420/36HS420

SECTION 5: DIAGRAMS

UY Board
AY Board
HAX Board
Pitch : 5mm
1
/ W
4
1
/ W in chip resistance.
16
KV-27HS420/29DRC420/30HS420/32HS420/34HS420/36HS420
The components identifi ed by shading and
only with part number specifi ed.
The symbol indicates a fast operating fuse and is displayed on the component
side of the board. Replace only with fuse of the same rating as marked.
Les composants identifi es per un trame et une marque
P/PA
securite. Ne les remplacer que par une piece portant le numero specifi e.
Board
Le symbole indique une fusible a action rapide. Doit etre remplace par une
fusible de meme yaleur, comme maque.
The components identifi ed by X in this basic schematic diagram
HBY
have been carefully factory-selected for each set in order to satisfy
Board
regulations regarding X-ray radiation. Should replacement be
necessary, replace only with the value originally used.
When replacing components identifi ed by Y, make the necessary
adjustments as indicated. If the results do not meet the specifi ed
value, change the component identifi ed by X and repeat the
adjustment until the specifi ed value is achieved.
When replacing the parts listed in the table below, it is important to
perform the related adjustments.
Part Replaced (Y)
DZ BOARD:
IC6503, IC8001, IC8002,
IC8004, IC8005, IC8104,
D8022, PH8003, Q8007,
Q8008, R6590, R8012,
R8014, R8015, R8016,
R8017, R8019, R8021,
R8027, R8029, R8030,
R8031, R8035, R8036,
R8037,R8038, R8039,
R8040, R8043, R8046,
R8052, R8059, R8060,
R8066, R8072, R8078,
R8079, R8082, R8165,
T8001

REFERENCE INFORMATION

RESISTOR
: RN METAL FILM
: RC SOLID
: FPRD NONFLAMMABLE CARBON
: FUSE NONFLAMMABLE FUSIBLE
: RW NONFLAMMABLE WIREWOUND
: RS NONFLAMMABLE METAL OXIDE
: RB NONFLAMMABLE CEMENT
: ADJUSTMENT RESISTOR
COIL
: LF-8L MICRO INDUCTOR
! symbol are critical for safety. Replace
! sont critiques pour la
Adjustment (X)
HV ADJUST
No HV Adjustment Required
CAPACITOR
: TA TANTALUM
: PS STYROL
: PP POLYPROPYLENE
: PT MYLAR
: MPS METALIZED POLYESTER
: MPP METALIZED POLYPROPYLENE
: ALB BIPOLAR
: ALT HIGH TEMPERATURE
: ALR HIGH RIPPLE
61