Shutter Housing Replacement - Polaroid 100 Series Repair Manual

bid
t)J!
Ih~'
front roll. imliLatin!,!. the modillcation
ha:.
lWl."1l Jon~'.
I. Rcpi;.hv
!
he
l>pr~~ld
roll sluing
t
Figure 5-7):
U"ld I h ... · rddiu:> end of tilt.' spring and insl'rt
tlw :.pring in till' fr:Jme roller support so thnt
Ih~' Inw~'r
l'ml of thl' spring seats on the
frnnl mJl :mpport tab.
Apply.oJ
downward
rr~'s~lIr~' on the upper end of the spring and
forc~' th~'
spring under the frame roller
support tab,
""!
Replacl" the front {shouldered) roU; Place
lill"
roll
bushinp on the roU and
insert
one
end of the roU in either
snppon. Spread
the
ot her support far enough to insert the roU.
Check the end-t<>-end
play
of the roll
in
the
supports. This side mcwement must not ex.­
ceed
.o:!o
inch.
If
it does, remove the roU
and tot' in
the
front
roll suppons. Re--install
the
ron
and recheck.
3. Replace the rear roU; Place the ron on top
of the fronl
ron
and line up the bushings with
the openings in the support. Press down
finn~
I)'
unti1 one end of the
ron
snaps
into
posi­
tion in the supporL Press down at the other
end until the roll is engaged in the support.
SHUTI'ER HOl:SING REPLACEMENT
Removal
[. R<'m(lh" I
h...
(ront
shutter
housing
and the
IXb~'
t'llol.:k aml de.:tronic module as follows:
J.
L.
\(,:nl! tlw
i'>.:llqW~
to detent lock-in.
h
Knllm\: I
Ill'
.,IILlth'T
housing screws (indud~
Jl)j.'
t!)~· lHlllSil1~ '~T"'\\ .11
fhe
lop of tht"
L·..
ble
,,-'1,,1-'" ,:o,,,;p
io~·.IIVd
on the bellows-side of
1!l\.'
r~',1f
"IHlner htm:'lIlj:! USing scrl'wdrivcr
.::: I
j
{1-tO.
iOn ':.JlUcr..:. where aprlicabk,
:\.'h'.I"~· Ih~'
front
shutt('r housing from the
1\'1' ~'l~-li pbk_ If
t[k'
el~h plate is d:lmaged
"1'1:", 1t"'1 It-.
:JJ!h·SJWIlC~.
discard iLl
,'.
\\h~'r;.:
apptk';lhk.
f~'mo\'e
lhe hasc block :lIld
('k,:1foni..'
Illutluk mounting screws holdmg
lh~
.,liull",r 10
tlw fronl shutt..:r housing. (On
.,Olll\.'
":;UTIcras.. the :.hutter simply rests on
I'I,!:-"!I~'
p'hb.!
d. On shutler-. with
copper"'COlorcd mylar
J)rin(ed eircuils:
~nte
the posltions of lilt:
btal.:t.: anti
WIllI\:
b<Jth:ry
WI~
kads. Using
an l·np r "sol<kr gobbler" 'or l'quivai1:nt
J.
carefully
IIn~oILl
.. · r the two
h.:;Ilis.
Cui off
and
S<lW
IhL' rubher
strain~rdief
collar blit
thl.! coUar and pee}
if off
the alhll..'j ;)nd df"JW
the battery win,' through th.: opening in the
rear shutter hOllsing,
On
shutters witb cleat
teflon printed circuits tolder Model 100
cameras): DO NOT UNSOLDER THE
BATI'ERY LEADS FROM THE CIRCUIT!
Open
the baUery compartment and unsolder
the
black
battery lead from the shutter inter­
lock. Snip the white Jead about an inch
away from the battery tenninaJ. Remove
and retain the metal banding dip and draw
the battery wire through the bellows tabs
and the opening in the rear shuUer housing.
On
other
shutters: Unsolder
the battery
leads diItctly from their contacts
On
the
electronic module, cut the collar (slit the
coJJar and peel
it
off the cable) and draw the
'wire through the opening in the shutter
hQusing.
2. Loosen
the cable
Itlease
cover retaining
screws and free the cable release from the
Itar
shutter housing. (Refer to Figures 5-21
and 5-22 for the following steps.)
3. To remove
the inner frame (top) from the
shutter housing. remove the detent from the
detent stud using smooth edged plier--.. (The
detent is press--fitted on
the
~ud,)
Then
un~
screw the detent stud from the shutter shaft,
thus releasing the inner frame (top).
4. To remove the inner frame {bottom
J
from
tbe shurter housing. remove the shutler
shaft screw and the two washers (if present)
from the shutter mount. Next remove the
shutter shaft and sleeve
(if
present) from the
housing.
5. Release the
U~frame
from the shutter hous
w
lng by sliding the bushing out of the key·
hole. Release the spring from the shutter
mQunt.
6. Collapse rhe beHows and remove the rc;.;r
shutler housing from the bellows as follows
j
ret:Jin the light seal).
Models 100.240_ 250_ 350
&
360;
Remove the four bellows screws.
All Other Models:
Remove the four bellows fasteners using tool
#11006 (Figure 5-8}. ,Some newer model