Dimplex LPC Series Installation Instructions page 2

inStallation With riGiD, e.m.t. conDUit or BX caBle
1. Remove screw holding the end cover and remove the cover.
2. Use suitable knockout for cable/conduit entrance. Secure in place on plate.
(Figure 2)
3. make electrical connections in the connection box, as shown in Figure 2.
Replace covers and secure baseboard in position.
Operation
Figure 5
a
C
B
D
A - Setting/Temperature Display
B - Economy Setting Icon
C - Set Back Temperature Setting
D - Comfort Setting Icon
E - Synchronized Icon
When power is first supplied to the LPC the Setpoint Temperature will flash in the
temperature display area. At any time either the + or - button can be pressed to
have the temperature setpoint displayed again.
a. Setting/Temperature Display
Pressing the + or - will increase or decrease the desired temperature for the room
to be heated by 0.5° (in either °C or °F).
After 5 seconds the Setpoint Temperature will switch to display the intake
temperature of the room.
!
nOTE: Pressing the + and - at the same time will toggle between °C and °F.
B. Economy Setting
The Economy Setting can be used to change the Setpoint Temperature for a
variable period of time. By pressing the v the Economy Setting will be enabled
- signified by the icon flashing. After the Set Back Temperature has been set, the
icon will become solid after three seconds and the Set Back Temperature will be
enabled.
To return back to the Comfort Setting press the v button and the
disappear and the icon will appear.
C. Set Back Temperature Setting
The Set Back Temperature Setting is used during periods when the Economy
setting feature is active. This temperature adjustment can be set by pressing the
v followed by the + or -.
D. Comfort Setting
The Comfort Setting icon will be displayed when the heater is in normal operation
based on the Setpoint Temperature for the room.
!
nOTE: Either the or
setting being used.
E. Synchronized icon
A wall mounted controller is available to control one or multiple Linear Proportional
Convector Heaters within a 50' (15 m) radius. In order for the wall setter to have
this function the Linear Proportional Convector and the Wall Setter need to be
1367 Industrial Road Cambridge ON Canada N1R 7G8
1-888-346-7539 www.dimplex.com
In keeping with our policy of continuous product improvement, we reserve the right to make changes without notice.
© 2011 Dimplex North America Limited
H
g
F
E
F - Lock Icon
G - Decrease Button
H - Increase Button
I - Menu Button
icon will always be visible, dependent on the
Synchronized.
1. On the Linear Proportional Convector press and hold the v button for 3
seconds, both the
2. Press the
3. Within 10 seconds press any button once on the Wall Setter.
!
note: There is a 3 second delay between pressing the last button the wall
setter and the LPC.
!
note: To desynchronize a Linear Proportional Convector from the
synchronized Wall Setter, on the Linear Proportional Convector:
Nothing will need to be done to the Wall Setter.
F. Lock icon
The Linear Proportional Convector Heater has a Button Lock feature, to prevent
settings from accidentally being changed.
1. Press and hold the
to flash.
i
2. To Enable:
will now be visible.
To Disable: Within 5 seconds press -, then +, then -, then +. The
will not be visible.
!
note: The LPC can be locked in either the Comfort or Economy Setting.
Ensure that the desired icons are present when locking is complete.
maintenance
CaUTiOn: Before removing the front cover for cleaning, make certain the
power has been turned off at the circuit breaker panel.
CaUTiOn: Allow adequate time for the element and body casing to cool
before attempting to work on the heater.
The LPC series contain no moving parts. Since the appliance contains no
moving parts little maintenance is required beyond vacuum cleaning. It is,
however, essential that the Linear Proportional Convector is not operated with an
accumulation of dust or dirt on the element, as this can cause a build up of heat
and eventual damage. For this reason the Linear Proportional Convector must be
inspected regularly, depending upon conditions and at least at yearly intervals.
Once cleaning is complete replace the front cover and restore power.

W arning: The user can perform cleaning ONLY. All other servicing should
be performed by qualified service personnel.
Warranty
icon will
The Manufacturer warrants the Linear Proportional Convector and components of the
enclosed product against any defect in material or workmanship for a period of one year from
the date of purchase, with the exception of the elements which are warranted to be free from
defect in material and workmanship for ten years. In full satisfaction of any claims under this
Warranty the manufacturer will repair or replace without charge, in its factory or in the field as
it alone may decide, any parts which in its opinion are defective.
The Manufacturer shall not be responsible for any transportation or shipping costs in relation
to such repair or replacement except as specifically assumed by it. misuse of this product
or repairs by persons other than the Manufacturer's authorized personnel without the
manufacturer's written approval will void this Warranty.
This Warranty is in lieu of all other warranties or conditions whether expressed or implied
including but not limited to those of merchantability or fitness for purpose and shall constitute
the sole remedy of the Purchaser and the sole liability of the Manufacturer in respect of the
sale of the product, whether in the nature of breach or breach of fundamental term, or of
negligence or otherwise.
The Manufacturer shall not be liable for any special, indirect or consequential damages or
for any damages resulting from removal or replacement of a Linear Proportional Convector
subject to warranty claim without the manufacturer's authorization.
This Warranty is transferable by the original consumer purchaser of the product. Any claims
under this Warranty must be submitted in writing to the Service manager, Dimplex North
America Ltd., 1367 Industrial Rd., Cambridge, Ontario N1R 7g8, Canada.
and icons will begin to flash.
- , + and then v, on the Linear Proportional Convector.
1. Press and hold the v for 3 seconds.
2. Press the v, + and then -.
v for 3 seconds. Both the
Within 5 seconds press +, then -, then +, then -. The
and Icons will begin
icon
icon
2