Lincoln Town Car 2005 Owner's Manual
  1. Manuals
  2. Brands
  3. Lincoln Manuals
  4. Automobile
  5. 2005 Town Car
  6. Owner's manual

Lincoln Town Car 2005 Owner's Manual

Hide thumbs Also See for Town Car 2005:
Table of Contents

Advertisement

Quick Links

Table of Contents

AM/FM stereo cassette with CD
Navigation system
Dual automatic temperature control
Headlamps
Message center
Locks
Anti-theft system
REVIEW COPY
2005 Town Car (tow), Owners Guide (post-2002-fmt) (own2002),
Market: USA_English (fus)
Table of Contents
4
10
10
15
17
17
21
25
87
87
90
91
91
94
95
101
101
102
114
115
117
123
131
131
142
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Town Car 2005 and is the answer not in the manual?

Questions and answers

Anthon Jones
July 8, 2025

Where can I locate oil light sensor

0

Subscribe to Our Youtube Channel

Related Manuals for Lincoln Town Car 2005

Summary of Contents for Lincoln Town Car 2005

  • Page 1 Table of Contents Table of Contents Introduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo cassette with CD CD changer Navigation system Climate Controls Dual automatic temperature control Rear window defroster Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment...

  • Page 2: Table Of Contents

    Table of Contents Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Tires, Wheels and Loading Tire Information Changing tires Lug Nut Torque Vehicle loading Trailer towing Recreational towing Driving Starting Brakes Traction control Air suspension Transmission operation Roadside Emergencies Getting roadside assistance Hazard flasher switch...

  • Page 3: Table Of Contents

    Table of Contents Maintenance and Specifications Engine compartment Engine oil Battery Fuel information Air filter(s) Refill capacities Lubricant specifications Accessories Index All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company.

  • Page 4: Introduction

    Introduction Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
  • Page 5 Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
  • Page 6 Introduction SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.
  • Page 7 Introduction Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury. Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passenger air bag.
  • Page 8 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation Child Seat Lower Warning Anchor Child Seat Tether Brake System Anchor Brake Fluid -...
  • Page 9 Introduction Vehicle Symbol Glossary Power Windows Power Window Lockout Front/Rear Interior Luggage Child Safety Door Compartment Release Lock/Unlock Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, Battery Acid or Sparks Explosive Gas Fan Warning Maintain Correct Fluid...

  • Page 10: Instrument Cluster

    Instrument Cluster Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
  • Page 11 Instrument Cluster Electronic throttle control: Illuminates when the engine has defaulted to a ’limp-home’ operation. Report the fault to a dealer at the earliest opportunity. Check fuel cap: Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Service engine soon warning light to come on.
  • Page 12 Instrument Cluster Air bag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately. A chime will also sound when a malfunction in the supplemental restraint system has been detected. Safety belt: Reminds you to fasten your safety belt.
  • Page 13 Instrument Cluster Air suspension: Illuminates when the air suspension is turned OFF or the air suspension system requires servicing. Washer: Illuminates when the windshield washer fluid is low. Speed control: Illuminates when the speed control is activated. Turns off when the speed control system is deactivated.
  • Page 14 Instrument Cluster Door ajar: Illuminates when any door is open (or not fully closed). Trunk ajar: Illuminates when the trunk is not completely closed. This light will flash and sound a tone for one second, then the light remains Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on.

  • Page 15: Gauges

    Instrument Cluster GAUGES Speedometer: Indicates the current vehicle speed. Select SPEED from the message center to display the digital speedometer on the left hand side of the cluster. Refer to the Message Center in the Driver Controls chapter for more information on the Trip A and B feature.
  • Page 16 Instrument Cluster Never remove the coolant reservoir cap while the engine is running or hot. Odometer: Registers the total miles TRUNK AJAR CHECK GAUGE (kilometers) of the vehicle. CHECK FUEL CAP AIR SUSPENSION O/D OFF DOOR AJAR SPEED CONTROL km/h MPH Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition...

  • Page 17: Entertainment Systems

    Entertainment Systems Entertainment Systems AUDIOPHILE AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED) MUTE AM/FM TAPE BASS TREB TUNE SCAN FADE AUTO SIDE COMP SHUF SEEK PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED) MUTE AM/FM TAPE BASS TREB TUNE SCAN FADE AUTO SIDE COMP SHUF SEEK REVIEW COPY...
  • Page 18 Entertainment Systems 1. Eject: Press to eject a tape. 2. Eject: Press to eject a CD. 3. Bass: Allows you to increase or decrease the audio system’s bass output. Press BASS then press SEL to decrease or increase the bass levels. Treble: Allows you to increase or decrease the audio system’s treble output.
  • Page 19 Entertainment Systems 8. REW (Rewind): Works in tape and CD modes. In tape mode, radio play continues until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. In CD mode, REW control reverses the CD within the current track. FF (fast forward): Works in tape and CD modes.
  • Page 20 Entertainment Systems 10. Autoset: Press to set first six strong stations into AM, FM1 or FM2 memory buttons; press again to return to normal stations. 11. Scan: Works in radio, tape and CD modes. Press SCAN for a brief sampling of radio stations, tape selections or CD tracks.

  • Page 21: Cd Changer

    Entertainment Systems REAR CONSOLE AUDIO CONTROLS (IF EQUIPPED) • NEXT: Press to access the next radio memory preset, the next CD track or the next tape selection. • VOL: Press the up arrow to increase the volume or the down arrow to decrease the volume.
  • Page 22 Entertainment Systems 2. Press to eject the magazine. 3. Pull the lever to remove a CD tray from the magazine. 4. Insert one disc into each CD tray of the magazine (up to 6 discs). Ensure that the label side is facing If you pull too hard on the disc holder, the disc holder may come completely out of the magazine.
  • Page 23 Entertainment Systems 6. Insert the CD magazine into the changer. 7. Slide the door to the left to close. Use only compact discs containing this mark. The magazine does not need to be full for the changer to operate. Radio power must be turned on to play the CDs in the changer. The magazine may be stored in the glove compartment when not being used.
  • Page 24 Entertainment Systems RADIO RECEPTION FACTORS There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, the weaker the signal and the weaker the reception. • Terrain: Hills, mountains, tall buildings, power lines, electric fences, traffic lights and thunderstorms can interfere with your reception.

  • Page 25: Navigation System

    Entertainment Systems CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
  • Page 26 Entertainment Systems 1. VOL-PUSH: Press to turn the system ON/OFF. Turn to adjust the audio volume level. 2. AUDIO: Press to enter audio mode and access radio, CD, CDDJ, DVD (if equipped) settings. 3. MAP: Press to enter map mode and view your current vehicle position on the map.
  • Page 27 Entertainment Systems Initial map display After pressing AGREE to the initial WARNING screen, you will move into the initial map screen which shows the current vehicle location. Pressing the globe icon will take you to the user settings — audible feedback, navigation units, language and clock (if equipped).
  • Page 28 Entertainment Systems To play a previously loaded CD: 1. Ensure that the vehicle ignition is on. 2. Press AUDIO. 3. Press CD to select a CD which is already loaded. (NO CD will appear in the display if there are no CDs loaded into the system). Use the controls (1–6) to select the desired CD.
  • Page 29 Entertainment Systems 2. Press DEST. The warning screen will appear. After reading, press AGREE. The screen will show a map with your current location. Press DEST again. 3. Select the desired type of destination entry. You may select “Address”, “Point of Interest”, “Emergency”...
  • Page 30 Entertainment Systems 4. Press DEST at the bottom of the map screen. 5. Choose the desired route by pressing the NEXT button (if it appears). There can be up to three alternative routes. 6. Press START to begin the navigation guidance. To adjust the voice guidance volume: 1.
  • Page 31 Entertainment Systems Press VOICE briefly (on your steering wheel controls) and the voice icon appears on the Navigation display. Press the REPEAT button or arrow on your steering wheel controls to hear the previous command repeated from the navigation system. The voice activated command feature will not operate if a map DVD is not inserted into the navigation DVD unit.
  • Page 32 Entertainment Systems Commands that jump over screens: • Current position • Current location • Map While in navigation map mode, the following commands are available: • Zoom in • Zoom out • Minimum scale • Maximum scale • North up •...
  • Page 33 Entertainment Systems • Chinese food • Continental restaurant • Continental food • French restaurant • French food • Italian restaurant • Italian food • Japanese restaurant • Japanese food • Mexican restaurant • Mexican food • Seafood restaurant • Seafood •...
  • Page 34 Entertainment Systems • Change to arrow guidance • Change to arrow guide • Turn list guidance • Turn list guide • Change to turn list guidance • Change to turn list guide • Entire route map • Entire route • Route overview •...
  • Page 35 Entertainment Systems Volume/power control Press knob to turn the audio system on/off. Turn to raise or lower volume. The levels will be displayed on the screen. To activate the navigation mode, press MAP or DEST. To adjust the navigation voice output level, select the NAV MENU button via the map screen.
  • Page 36 Entertainment Systems 3. SCV is located in the middle of the screen. Press to turn on. 4. Select setting 1 to 7 or turn off. The recommended level for the speed compensated volume is from level 1 through level 3. When activated, level 1 is the minimum setting and level 7 is the maximum setting.
  • Page 37 Entertainment Systems Tune adjust Press TUNE to manually move down/up ( ) the frequency band. In CD mode, press TRACK to select the previous/next ( Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations.
  • Page 38 Entertainment Systems Scan Press SCAN for a brief sampling of SOUND all listenable stations and CD tracks. SEEK TUNE Press again to disable and remain on SCAN PRESET SCAN AUTO SET the current selection. TRAFFIC INFO SET PTY 87.9 89.9 98.1 98.5 106.3...
  • Page 39 Entertainment Systems Traffic information not available in most U.S. markets. Information feature Press INFO to view the frequency, SOUND call letters and PTY category of the SEEK TUNE selected FM station. SCAN PRESET SCAN AUTO SET TRAFFIC INFO SET PTY 87.9 89.9 98.1...
  • Page 40 Entertainment Systems • Soft • Top 40 Once PTY has been programmed, press SEEK ( ) or SCAN to initiate a search up or down the frequency. Preset scan and Autoset also initiate PTY searches. The search will stop when the desired program type has been reached. If no program type is found, a message will display.
  • Page 41 Entertainment Systems Bass : Allows you to increase or decrease the audio system’s bass output. Treble : Allows you to raise or lower the audio system’s treble output. Fade : Allows you to adjust the amount of sound emitted from the front and rear speakers.
  • Page 42 Entertainment Systems Satellite ready capability Your Lincoln navigation system comes equipped with Satellite ready capability. The kit to enable Satellite reception is available through your Lincoln dealer. Detailed Satellite instructions are included with the dealer installed kit. CD mode CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only.
  • Page 43 Entertainment Systems Press CD. CD play will begin where it stopped last. Loading a CD: 1. Press CD OPEN CLOSE on the bezel. REVIEW COPY 2005 Town Car (tow), Owners Guide (post-2002-fmt) (own2002), Market: USA_English (fus)
  • Page 44 Entertainment Systems 2. The navigation screen will fold down, allowing you access to the in-dash six CD system. 3. Press LOAD and the desired CD slot number. The indicator light will blink slowly at first, then quickly, signaling the system is ready. 4.
  • Page 45 Entertainment Systems Rewind/fast forward in CD mode Press to reverse or advance ) in the current CD track. Scan feature in CD mode Press SCAN to hear a brief sampling of all tracks on the current CD. Press again to disengage and remain with the current track.
  • Page 46 Entertainment Systems Pause In CD mode, press PAUSE to pause the current track. Press again to continue playing. Map mode Map display information To access the map display, press MAP on the bezel. Once pressed, the current map display will appear on the screen showing the current vehicle location.
  • Page 47 Entertainment Systems Zoom control When ’Zoom’ is pressed, the scale indicator is shown on the screen. The scale markings are: 1/32, 1/16,1/4, 1/8, 1/2, 1, 2, 4, 8, 16, 32, 64, 128 miles. The control can be used in a number of ways: •...
  • Page 48 Entertainment Systems Route preferences After entering a destination, the Route preferences will appear on the screen showing what is currently selected. You may choose to activate/deactivate selections which the system will factor in when calculating your route. Those options are: •...
  • Page 49 Entertainment Systems You will be able to view the information (if available) as well as choose to store the destination as a memory point by pressing OK. Screen symbols Navigation symbol — Indicates the current vehicle position and points to the direction in which the vehicle is currently traveling.
  • Page 50 Entertainment Systems Avoid areas or points — The “X” symbol indicates a point. to be avoided in route calculations. If the avoid point is enlarged to an avoid area, it will appear on the screen as a shaded box. Way point symbol — Indicates the location of a way point (locations you wish to visit in route to your ultimate destination) on the map.
  • Page 51 Entertainment Systems Once pressed, the Navigation Menu will display showing the following options: • Route Options/Preferences • Navigation Set Up • Display Options • Stored Locations • On Route Scroll • Voice Guidance/Volume Depending upon whether or not a route is active will determine if route options/route preferences is contained on the Navigation Menu.
  • Page 52 Entertainment Systems Ensure that you follow highway code restrictions and do not take any risks. For example, if you are unable to make a U-turn, continue on your journey. The navigation system will recalculate your route to get you back to an appropriate road to your destination. Navigation set up The Navigation Set up screen will allow you to make adjustments to...
  • Page 53 Entertainment Systems Restore system defaults Resets all system user-selectable options to the default (automatic) values (i.e. guidance, voice, search area and route preferences). Calibration This feature is helpful if the car has been towed, or if you notice it is not registering at the correct vehicle location on the map.
  • Page 54 Entertainment Systems Display Options The Display Options screen will allow you make adjustments to the navigation display screen. You can choose from: • Map Mode (Dual or Full) • Guidance Mode (Arrows or Turn list) • Guidance Display (On or Off) •...
  • Page 55 Entertainment Systems In this screen, you can select from Memory Points, Special Memory Points, Home, Avoid Area, Destination and Way Point, or Previous Destination. Please refer to the Destination menu section for a complete description of the functions. On route scroll The system automatically scrolls through the entire planned navigation route either forwards or...
  • Page 56 Entertainment Systems 3. Press the speaker icon to turn the voice guidance option on/off. Press the desired number to select the volume level for the voice prompts. Home To set home for the first time: 1. Press MAP. 2. Press “Nav. Menu”. 3.
  • Page 57 Entertainment Systems 4. Press “Home”. 5. Press “Add”. 6. Select the desired menu item you wish to set as Home (Address, Memory Point, Point of Interest, Previous Destination). 7. Enter the required details. 8. Press OK to set the home position.
  • Page 58 Entertainment Systems To view the set home position 1. Press MAP. 2. Press “Nav. Menu”. 3. Press “Stored Locations”. 4. Press “Home”. 5. Press “List”. REVIEW COPY 2005 Town Car (tow), Owners Guide (post-2002-fmt) (own2002), Market: USA_English (fus)
  • Page 59 Entertainment Systems Deleting a home location 1. Press MAP. 2. Press “Nav. Menu”. 3. Press “Stored Locations”. 4. Press “Home”. 5. Press “Delete”. REVIEW COPY 2005 Town Car (tow), Owners Guide (post-2002-fmt) (own2002), Market: USA_English (fus)
  • Page 60 Entertainment Systems 6. Press YES to confirm. Special memory points There are five possible special memory points that you can set. To set a memory point: 1. Press the MAP hard key. 2. Press “Nav. Menu”. REVIEW COPY 2005 Town Car (tow), Owners Guide (post-2002-fmt) (own2002), Market: USA_English (fus)
  • Page 61 Entertainment Systems 3. Press “Stored Locations”. 4. Press “Special Memory”. 5. Press “Add” and select a position. 6. Select point 1–5. 7. Input a destination. 8. Press OK. Once all five special memory points are entered, the “Add” control will read as “Full”.
  • Page 62 Entertainment Systems 3. Press “Stored Locations”. 4. Press “Special Memory”. 5. Press “Delete”. The list will display. 6. Select the special memory point to delete. 7. Press “Del. all” to delete all entered special memory points. 8. Press “Yes” to confirm. Detour options You may engage the detour option once a route has already been calculated by the system.
  • Page 63 Entertainment Systems Press DETOUR to activate. Use the soft controls to select and enter the number of miles you want to deviate off of the current road. Press DETOUR to confirm the selection and to activate the detour around the specified areas. Press NEW ROUTE if you would like the system to plan a different route.
  • Page 64 Entertainment Systems Avoiding an area while under guidance For one reason or another, you may choose to avoid a certain area while in route to your destination. To select the area to avoid: • From the MAP screen, press Nav Menu.
  • Page 65 Entertainment Systems Deleting areas to avoid To delete a selection from the “Avoid area” list: • From the stored locations menu, select “Avoid area”. • Press DELETE • Select the desired area to be deleted. • Press DEL. ALL to delete all stored areas.
  • Page 66 Entertainment Systems Initial map display After pressing AGREE to the initial WARNING screen, you will move into the initial map screen which shows the current vehicle location. Pressing the globe icon will take you to the user settings — audible feedback, navigation units, language and clock (if equipped).
  • Page 67 Entertainment Systems Selecting a destination Press DEST to set a destination. From this menu, you may select from the following options: • Address— Use to select a destination based on a known street address. • Point of Interest— Use to select a destination that is a point of interest location (i.e., airport, restaurant, hospital).
  • Page 68 Entertainment Systems 2. Input the house/building number and press OK. 3. Use the keyboard to type in the street name. When you are typing the street name, the system may bring up possible roads that you can select from. Use the arrows to scroll up or down to select the desired street.
  • Page 69 Entertainment Systems 5. You may use the keyboard to input the desired city. Points of interest (POI) Select “Point of Interest” from the Destination Entry Menu. In this next menu, you will have the following options: • By Name— Enter POI name on the keyboard.
  • Page 70 Entertainment Systems Deleting stored locations Your navigation system allows you to delete any stored locations (previous destinations, memory points, special memory points, home, avoid areas, destination and way points, etc.) To delete any of these stored locations: 1. Press the MAP hard key. 2.
  • Page 71 Entertainment Systems 4. Select the desired item you wish to delete (previous destination, memory point, etc.). 5. Press “Delete” at the bottom of the screen. 6. The list of stored locations will be displayed. 7. Select (touch) the entry to be deleted.
  • Page 72 Entertainment Systems This screen will list the closest police station, hospital and dealer to your current location. Memory point Your navigation system allows you to go to special destinations you may wish to again visit. To view any of these “memory points” without a route calculated: 1.
  • Page 73 Entertainment Systems 1. Press the MAP hard key. 2. Press “Nav Menu” in the bottom left hand corner of the screen. 3. Press “Stored locations”. 4. Select “Memory Point”. 5. Press “Add” at the bottom of the screen. 6. Select the desired menu item. 7.
  • Page 74 Entertainment Systems To give the new memory point a name: 1. Select it from the list. 2. Press NAME. 3. Enter the desired name. Accessing memory point lists 1. Press the MAP hard key. 2. Press “Nav Menu” in the bottom left hand corner of the screen. 3.
  • Page 75 Entertainment Systems 4. Press “Memory Point”. 5. Press LIST 6. Select the desired entry to view its location details. Sorting memory point lists 1. Access the desired list. 2. Press the button to sort the list as desired (i.e. date, name, or icon). When sorted by distance, the points are ordered by distance from the current vehicle location.
  • Page 76 Entertainment Systems Choosing from the icon list After selecting a location, press ICON to edit. There will be 15 normal and three sound icons displayed. Press the icon you wish to use. The normal icons will be displayed on the map to indicate the map location identified with that icon.
  • Page 77 Entertainment Systems Freeway Entrance/Exit To set a freeway entrance or exit as a destination: 1. Press the DEST hard key. 2. Press “ Next page” to access the second page of the Destination Entry menu. 3. Select “Freeway Entrance/Exit”. 1. Enter freeway name— Enter the freeway name using the keyboard.
  • Page 78 Entertainment Systems Destination and way points The Store Dest. & Way Point menu is used after a destination or way point has been entered for the first time using the Destination Entry menu. You can store and delete destinations and way points (locations you wish to visit in route to your ultimate destination).
  • Page 79 Entertainment Systems Editing and changing order of way points and destination Press “Chg. Order” to change the order in which the way points are visited. The points are listed chronologically from bottom up, the destination being on the top. Press the MAP button to edit the way point location on the map display.
  • Page 80 Entertainment Systems Route calculation Once the route criteria is selected, the navigation system automatically calculates the selected destination. The route appears on the display screen and a voice prompt provides instructions. The system may calculate up to four routes for the desired destination. Press “Next”...
  • Page 81 Entertainment Systems To access menu mode, press the MENU hard control. Menu mode allows you to access: • System Set-up • Information — Gives you the Lincoln Customer Assistance Center information. • Brightness/Contrast — Allows you to adjust the brightness and contrast on the screen.
  • Page 82 Entertainment Systems System setup The system set up menu contains the following user settings: • Audible Feedback — Press to activate audible voice navigation commands. Press again to deactivate. • Navigation Units — Press to toggle between Metric/English units. • Language — Press to toggle between English, French, or Spanish.
  • Page 83 Entertainment Systems Do not use the navigation system to locate emergency services. For road safety reasons, the driver should program the system only when the vehicle is stationary. Certain functions will therefore not operate while the vehicle is in motion. The map database DVD does not reflect road detours, closures or construction, road characteristics such as rough road surface, slope or grade, weight or height restrictions, traffic congestion, weather or similar...
  • Page 84 Entertainment Systems Radio reception factors There are certain factors that may effect your radio reception. • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations.
  • Page 85 Entertainment Systems • roads under cliffs Ensure that you do not have any metal objects on the rear parcel shelf. If your windows are tinted, ensure that you use non-metal tinting instead of metal oxide tinting. Both of these factors can interrupt GPS reception. Cleaning the display Do not spray cleaning fluid directly onto the unit.
  • Page 86 Entertainment Systems Ordering additional map DVDs If you wish to order a replacement or additional map, please call 1–888–NAV-MAPS (1–888–628–6277) or to log onto www.navtech.com. Latest map DVDs The map content is constantly changing due to new roads, traffic restrictions, etc. . Therefore, it is not always possible to exactly match the DVD map with the current roadways.

  • Page 87: Climate Controls

    Climate Controls Climate Controls DUAL ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (DEATC) SYSTEM 1. A/C control: Cools the vehicle and is used to reduce humidity in the vehicle. Press to turn on/off. 2. Recirculation control: Cools the vehicle more quickly by recirculating the cabin air instead of using outside air and helps prevent unpleasant outside odors or fumes from entering the vehicle.
  • Page 88 Climate Controls : Distributes air through the windshield defroster vents and the side window demisters. : Distributes air through the windshield defroster vents, the side window demisters and floor vents. : Distributes air through the floor vents. : Distributes air through the instrument panel vents and the floor vents.
  • Page 89 Climate Controls 16. Temperature conversion: Press to toggle between Fahrenheit and Celsius temperature on the DEATC display only. The set point temperatures in Celsius will be displayed in half-degree increments. OPERATING TIPS • To reduce fog build up on the windshield during humid weather, place the air flow selector in the position.

  • Page 90: Rear Window Defroster

    Climate Controls REAR CONSOLE CLIMATE CONTROLS (IF EQUIPPED) • TEMP: Press to increase or decrease airflow temperature. • FAN: Press to increase or decrease the fan speed. REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog.

  • Page 91: Lights

    Lights Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Turns the headlamps on. Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
  • Page 92 Lights 7. Steps 3 through 5 need to be performed within 10 seconds. Daytime running lamps (DRL) (if equipped) The daytime running light system turns the headlamps on, with a reduced light output, when: • the ignition is in RUN, •...
  • Page 93 Lights PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight and parklamp operation. • Rotate the thumbwheel from left to right to brighten the instrument panel. • Rotate the thumbwheel from right to left to dim the instrument panel.

  • Page 94: Turn Signal Control

    Lights 3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood. 4. On the wall or screen you will observe an area of high intensity light. The top of the high intensity area should touch the horizontal reference line, if not, the beam will need to be adjusted.
  • Page 95 Lights INTERIOR LAMPS Map/Courtesy lamps To turn on the map lamps, press the map lamp control. Rear courtesy/reading lamps The courtesy lamp lights when: • any door is opened. • any of the remote entry controls are pressed and the ignition is OFF.

  • Page 96: Bulb Replacement

    Lights Using the right bulbs Replacement bulbs are specified in the following chart. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.
  • Page 97 Lights Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position. 2. Remove the protective bulb cover by loosening and removing the five screws. 3. Rotate the light bulb socket counter clockwise and pull it straight out from the assembly.
  • Page 98 Lights 3. Rotate the bulb socket counterclockwise and remove from lamp assembly. 4. Carefully pull bulb straight out of the socket and push in the new bulb until it snaps, locking it into position. 5. To complete installation, follow the removal procedure in reverse order.
  • Page 99 Lights 8. Install the plastic retainer and carefully push the carpet back into place. Replacing license plate lamp bulbs 1. Make sure headlamp switch is in OFF position, then remove two screws, grommets and the license plate lamp assembly from the trunk lid.
  • Page 100 Lights Overhead console lamps To remove and replace the lamps in the overhead console: 1. Make sure the headlamp switch is in the OFF position and remove the overhead console from the headliner. 2. Remove the bulb socket from the back of the lamp housing by pulling it straight out.

  • Page 101: Driver Controls

    Driver Controls Driver Controls MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Windshield washer: Push the end of the stalk: •...
  • Page 102 Driver Controls 5. To prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element.
  • Page 103 Driver Controls 1. From a blank display (OFF), press and release the MODE button once to enter the compass mode. 2. Press and release the MODE button again to enter the oil minder mode. 3. Press and release the MODE button again to return to OFF.
  • Page 104 Driver Controls 4. The overhead console displays the compass heading in one of eight directions: NORTH, NORTHEAST, EAST, SOUTHEAST, SOUTH, SOUTHWEST, WEST, and NORTHWEST. Zone variation mode Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. A correct zone setting will eliminate compass heading error.
  • Page 105 Driver Controls Calibration mode For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. To calibrate the compass: 1. Press and release the MODE button until the compass directional heading is displayed. 2.
  • Page 106 Driver Controls HomeLink wireless control system (if equipped) The HomeLink Wireless Control System, located on the overhead console, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.
  • Page 107 Driver Controls • After about 20 seconds, the message CHANNELS CLEARED will appear. Do not repeat step one to program additional hand-held transmitters to the remaining two HomeLink buttons. This will erase previously programmed hand-held transmitter signals into HomeLink . 2.
  • Page 108 Driver Controls 4. When the message CHANNEL “X” (1,2 or 3) TRAINED appears on the display, release both the HomeLink and hand held transmitter buttons. • DID NOT TRAIN will be displayed if the channel did not properly train. 5. Press and hold the just-trained HomeLink button and observe the HomeLink house icon on the display.
  • Page 109 Driver Controls 8. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming.
  • Page 110 Driver Controls Erasing HomeLink buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outside buttons. The message CLEARING CHANNELS will appear on the HomeLink display. • After about 20 seconds, the message CHANNELS CLEARED will appear on the display.
  • Page 111 Driver Controls 2. The display will change to CHANNEL “X” (1,2, or 3) TRAINING after 20 seconds. Without releasing the HomeLink button, follow step 2 in the “Programming” section. For questions or comments, contact HomeLink at www.homelink.com or 1–800–355–3515. Oil minder mode Normal mode To enter oil minder mode, press the MODE button repeatedly until OIL...
  • Page 112 Driver Controls Change oil now The overhead console will warn the user that the oil needs changing when CHANGE OIL NOW is displayed. This warning will remain on until the oil life is reset in oil minder mode (unless a higher priority message is requested).
  • Page 113 Driver Controls To de-activate park assist: 1. Press the OFF button to de-activate. PARK ASSIST DISABLED will be displayed and the button will be backlit amber. 2. Press the OFF button again to re-activate. The button will be backlit green at night time when the headlamps are ON.

  • Page 114: Power Windows

    Driver Controls Do not use the power point for operating the cigarette lighter element. The Maximum power each power point can supply depends on the fuse rating. For example: a 20A fuse should supply a maximum of 240 Watts, a 15A fuse should supply a maximum of 180 Watts and a 10A fuse should supply a maximum of 120 Watts.

  • Page 115: Mirrors

    Driver Controls One touch down • Press AUTO completely down and release quickly. The driver’s window will open fully. Depress again to stop window operation. One touch down can be deactivated during operation by pushing down on the top part of the driver power window control.
  • Page 116 Driver Controls Without Navigation System The mirror automatically adjust (darken) to minimize glare. With Navigation System The illuminated LED to the right of the AUTO button indicates if the mirror is in the auto-dimming function. To turn the mirror off push the OFF button until the LED goes out.

  • Page 117: Speed Control

    Driver Controls Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position.
  • Page 118 Driver Controls Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release 2. Accelerate to the desired speed. 3. Press the SET + control and release it.
  • Page 119 Driver Controls Resuming a set speed Press the RESUME control and release it. This will automatically return the vehicle to the previously set speed. The RESUME control will not work if the vehicle speed is not faster than 30 mph (48 km/h). Increasing speed while using speed control There are two ways to set a higher speed:...
  • Page 120 Driver Controls • Depress the brake pedal until the desired vehicle speed is reached, press the SET + control. Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’s previously set speed.
  • Page 121 Driver Controls In any mode: • Press VOL + or - to adjust the volume. Climate control features (if equipped) • Press TEMP + or - to adjust temperature. Navigation control features (if equipped) Press and hold VOICE briefly until the voice icon appears on the Navigation display to use the...
  • Page 122 Driver Controls Rear radio/climate controls lockout The rear radio/climate control feature can be locked out by pressing the 3 and the 5 buttons on the radio simultaneously while the radio is on. To enable the rear radio/climate controls, press the 3 and the 5 buttons again.

  • Page 123: Message Center

    Driver Controls A driver’s first responsibility is the safe operation of the vehicle. The most important thing you can do to prevent a crash is to avoid distractions and pay attention to the road. Wait until it is safe to operate Mobile Communications Equipment.
  • Page 124 Driver Controls Selectable features Select Each press of the SELECT control will select a different feature as follows: • SPEED • FUEL ECON • DIST TO EMPTY • AVG SPEED • TRIP A/TRIP B • E/M For descriptions of the SELECT features, refer to “Message center functions”...
  • Page 125 Driver Controls Fuel econ (average fuel economy) Select this function to display your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing gallons of fuel used by 100 miles traveled (kilometers traveled by liters used), your figure may be different than displayed for the following reasons: •...
  • Page 126 Driver Controls 3. Press the RESET control to clear SELECT RESET the system memory. • Actual highway fuel economy is now displayed. This current average measure will change as the speed control system changes the engine speed to maintain a constant vehicle speed.
  • Page 127 Driver Controls AVG speed To use this function, select AVG SPEED and press the RESET control. Your average speed from that point will be displayed until RESET is pressed again. Trip A B These two functions allow you to see how far you have traveled since you last reset.
  • Page 128 Driver Controls POWER TRUNK (IF EQUIPPED) Your vehicle may be equipped with a power trunk controlled by the interior trunk control, the key fob or the keypad on the door. If anything obstructs the power trunk while it is closing, the trunk will automatically reverse to the open position, provided it meets sufficient resistance.
  • Page 129 Driver Controls FUEL DOOR RELEASE Your vehicle is equipped with a locking fuel door. To open the door, press the control located on the door. Fuel filler door override release If the remote release is inoperative, open the trunk, then pull the override release handle located inside the trunk to open the fuel filler door.
  • Page 130 Driver Controls Remote seat adjustment The rear passenger can move the front passenger seat forward or backward using the control located in the rear center console. Move the control forward or backward to move front passenger seat. Remote seat adjustment lockout The window lockout control, located WINDOW LOCK on the drivers door, will also lockout...

  • Page 131: Locks And Security

    Locks and Security Locks and Security KEYS Your vehicle is equipped with a master key and a valet (identified with the word VALET) key lock system. The master key will access: • the driver’s door, • the trunk, • the glove box, •...
  • Page 132 Locks and Security Central locking/unlocking • All doors are locked when the key is inserted into the driver door key cylinder and turned to the lock position. • The driver’s door is unlocked when the key is inserted into the driver door key cylinder and turned to the unlock position.
  • Page 133 Locks and Security To open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated “T” shaped handle and push up on the trunk lid. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light.
  • Page 134 Locks and Security Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The typical operating range for your remote entry transmitter is approximately 33 feet (10 meters). A decrease in operating range could be caused by: •...
  • Page 135 Locks and Security • until the vehicle doors are locked using the remote entry transmitter or the power door unlock control. Locking the doors Press and release to lock all the doors. Note: The interior lamps will turn off and the parklamps will flash, if all the closures (doors, trunk, hood) are closed.
  • Page 136 Locks and Security • Wait 2 minutes and 45 seconds for the alarm to time-out. Opening the trunk Press once to open the trunk. If your vehicle is fitted with the optional power decklid, press twice to open the trunk and twice to close it. Before operating the power decklid, be sure that no one, particularly a child, is in a position where he or she can be injured by the trunk lid.
  • Page 137 Locks and Security 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery.
  • Page 138 Locks and Security To reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Cycle eight times rapidly (within 10 seconds) between the 1 (OFF/LOCK) position and the 3 (ON) position. Note: The eighth turn must end in the 3 (ON) position.
  • Page 139 Locks and Security • any door is open. The battery saver will shut off the interior lamps 30 minutes after the last door is closed, or after 10 minutes if the last door is left open. Autolock This feature automatically locks all vehicle doors when the following conditions are met: •...
  • Page 140 Locks and Security Press once to unlock the driver’s door and move the memory features to the corresponding memory position, just as if you had pressed the memory control in the vehicle. Activating the memory seat/mirrors/adjustable pedals feature To activate this feature: 1.
  • Page 141 Locks and Security Programming a personal entry code To create your own personal entry code: 1. Enter the factory set code. 2. Within five seconds press the 1 • 2 on the keypad. 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other.

  • Page 142: Anti-Theft System

    Locks and Security To unlock all doors, press the 3 • 4 control within five seconds. To lock all doors, press the 7 • 8 and the 9 • 0 at the same time. You do not need to enter the keypad code first. Note: The interior lamps will turn off.
  • Page 143 Locks and Security • When the ignition is in the 1 (OFF/LOCK) position, the indicator will flash once every 2 seconds to indicate the SecuriLock system is functioning as a theft deterrent. • When the ignition is in the 3 (ON) position, the indicator will glow for 3 seconds to indicate normal system functionality.
  • Page 144 Locks and Security Programming spare keys You can program your own coded keys to your vehicle. Please read and understand the entire procedure before you begin. Tips: • A maximum of eight keys can be coded to your vehicle. • Only use SecuriLock keys.
  • Page 145 Locks and Security To program additional new unprogrammed key(s), repeat this procedure from Step 1 for each additional key. PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will warn you in the event of an unauthorized entry to your vehicle. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are taken to the dealership to aid in troubleshooting.

  • Page 146: Seating And Safety Restraints

    Seating and Safety Restraints Seating and Safety Restraints SEATING Adjustable head restraints Your vehicle’s seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
  • Page 147 Seating and Safety Restraints Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. To adjust the front seatback using the manual recliner: • Lift and hold the handle located on the side of the seat.
  • Page 148 Seating and Safety Restraints Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
  • Page 149 Seating and Safety Restraints Press to move the front portion of the seat cushion up or down. Press to move the rear portion of the seat cushion up or down. Heated seats (if equipped) To operate the heated seats: • Push the indicated side of the control for maximum heat.
  • Page 150 Seating and Safety Restraints The heated seat module resets at every ignition run cycle. While the ignition is in the ON position, activating the high or low heated seat switch enables heating mode. When activated, they will turn off automatically when the ignition is turned to the OFF position. The indicator light will illuminate when the heated seats have been activated.

  • Page 151: Safety Restraints

    Seating and Safety Restraints • To program position two, repeat the previous procedure using control • To program position three, repeat the previous procedure but press controls 1 and 2 simultaneously. A position can only be recalled when the transmission gearshift is in Park.
  • Page 152 Seating and Safety Restraints How does the Personal Safety System work? The Personal Safety System can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the Restraints control module (RCM).
  • Page 153 Seating and Safety Restraints Front passenger sensing system For air bags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the air bag when it begins to inflate. For some occupants, like infants in rear-facing child seats, this occurs because they are initially sitting very close to the air bag.
  • Page 154 Seating and Safety Restraints Front safety belt pretensioners The safety belt pretensioners at the front outboard seating positions are designed to tighten the safety belts firmly against the occupant’s body during a frontal or near-frontal collision. This maximizes the effectiveness of the safety belts and helps properly position the occupant relative to the air bag to improve protection.
  • Page 155 Seating and Safety Restraints Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To reduce the risk of injury, make sure children sit in the back seat where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving.
  • Page 156 Seating and Safety Restraints Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. Combination lap and shoulder belts 1.
  • Page 157 Seating and Safety Restraints Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 5 mph (8 km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.
  • Page 158 Seating and Safety Restraints • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
  • Page 159 Seating and Safety Restraints Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front outboard passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height adjuster down.
  • Page 160 Seating and Safety Restraints The lap belt does not adjust automatically. Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
  • Page 161 Seating and Safety Restraints Conditions of operation If... Then... The driver’s safety belt is not The safety belt warning light buckled before the ignition illuminates 1-2 minutes and the switch is turned to the ON warning chime sounds 4-8 seconds. position...
  • Page 162 Seating and Safety Restraints If... Then... The driver’s and front The BeltMinder feature will not passenger’s safety belts are activate. buckled before the ignition switch is turned to the ON position or less than 1-2 minutes have elapsed since the ignition switch has been turned ON...
  • Page 163 Seating and Safety Restraints Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime.
  • Page 164 Seating and Safety Restraints Reasons given... Consider... “I have an air bag” Air bags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. “I’d rather be thrown clear” Not a good idea.
  • Page 165 Seating and Safety Restraints • The gearshift is in P (Park) (automatic transmission) • The ignition switch is in the OFF position • The driver and front passenger safety belts are unbuckled To reduce the risk of injury, do not deactivate/activate the Belt Minder feature while driving the vehicle.

  • Page 166: Air Bags

    Seating and Safety Restraints Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts.
  • Page 167 Seating and Safety Restraints Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly; there is a risk of injury from a deploying air bag.
  • Page 168 Seating and Safety Restraints Do not attempt to service, repair, or modify the steering column, its adaptive module, or its fuses. See your Ford or Lincoln Mercury dealer. To properly position yourself away from the air bag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably.
  • Page 169 Seating and Safety Restraints Children and air bags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.
  • Page 170 Seating and Safety Restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
  • Page 171 Seating and Safety Restraints If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
  • Page 172 Seating and Safety Restraints When the front passenger seat is occupied and the sensing system has turned off the passenger’s frontal airbag, the passenger airbag off or pass airbag off indicator will light and stay lit to remind you that the front passenger frontal airbag is off.
  • Page 173 Seating and Safety Restraints Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor.
  • Page 174 Seating and Safety Restraints Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to Air bag readiness section in the Instrument Cluster chapter. Routine maintenance of the air bag is not required.
  • Page 175 Seating and Safety Restraints All occupants of the vehicle should always wear their safety belts even when an air bag SRS is provided. How does the side air bag system work? The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as...
  • Page 176 Seating and Safety Restraints to inflate in side-impact collisions, not roll-over, rear-impact, frontal or near-frontal collisions, unless the collision causes sufficient lateral deceleration. Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again.

  • Page 177: Child Restraints

    Seating and Safety Restraints SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air bag supplemental restraint system (SRS) in this chapter for special instructions about using air bags. Important child restraint precautions You are required by law to use safety restraints for children in the U.S.
  • Page 178 Seating and Safety Restraints Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 pounds (18 kg) and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly, which could increase the risk of serious injury.
  • Page 179 Seating and Safety Restraints Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child’s head (top...
  • Page 180 Seating and Safety Restraints Follow all instructions provided by the manufacturer of the booster seat. Never put the shoulder belt under a child’s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. Never use pillows, books, or towels to boost a child.
  • Page 181 Seating and Safety Restraints • LATCH lower anchors are recommended for use by children up to 48 pounds (22 kg) in a child restraint. Top tether anchors can be used for children up to 60 pounds (27 kg) in a child restraint, and to provide upper torso restraint for children up to 80 pounds (36 kg) using an upper torso harness and a belt-positioning booster.
  • Page 182 Seating and Safety Restraints 1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat...
  • Page 183 Seating and Safety Restraints 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it.
  • Page 184 Seating and Safety Restraints 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward.
  • Page 185 Seating and Safety Restraints 2. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seatback.
  • Page 186 Seating and Safety Restraints Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. This type of child seat eliminates the need to use seat belts to attach the child seat.
  • Page 187 Seating and Safety Restraints If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat.

  • Page 188: Tires, Wheels And Loading

    Tires, Wheels and Loading Tires, Wheels and Loading INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
  • Page 189 Tires, Wheels and Loading The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
  • Page 190 Tires, Wheels and Loading • Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire’s load carrying capability.
  • Page 191 Tires, Wheels and Loading Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove stones, nails, glass or other objects that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs.
  • Page 192 Tires, Wheels and Loading higher than the manufacturer’s recommended cold inflation pressure which can be found on either the tire label or certification label which is located on the B-Pillar or the edge of the driver’s door. The cold inflation pressure should never be set lower than the recommended pressure on the tire label or certification label.

  • Page 193: Tire Information

    Tires, Wheels and Loading TIRE REPLACEMENT REQUIREMENTS Your vehicle is equipped with tires designed to provide a safe ride and handling capability. Only use replacement tires and wheels that are the same size and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford.
  • Page 194 Tires, Wheels and Loading When driving with the T-type/mini-spare tire do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label • Tow a trailer • Use snow chains on the end of the vehicle with the T-type/mini spare tire •...
  • Page 195 Tires, Wheels and Loading • Use snow chains on the end of the vehicle with the dissimilar spare tire/wheel The usage of a dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise •...
  • Page 196 Tires, Wheels and Loading 1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park), turn engine OFF and block the diagonally opposite wheel. 3. Remove the spare tire and the jack.
  • Page 197 Tires, Wheels and Loading 4. Remove the lug wrench (A) from the jack. Rotate the lug wrench socket out from the handle. 5. Locate pry off notch (if equipped) and remove the center ornament from the aluminum wheel with the tapered end of the wheel nut wrench that came with your vehicle.
  • Page 198 Tires, Wheels and Loading JACK LOCATION-REAR The jack location markings can be found on the lower outer edge of the body. • Locate the jack locator mark (B - triangle) on the body (C) near the tire you are changing, then place the jack (D) under the frame (A) of the vehicle aligning it with the mark (B -...

  • Page 199: Lug Nut Torque

    Tires, Wheels and Loading 8. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 9.
  • Page 200 Tires, Wheels and Loading INFORMATION CONTAINED ON THE TIRE SIDEWALL Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S.
  • Page 201 Tires, Wheels and Loading 7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure.
  • Page 202 Tires, Wheels and Loading 10. Tire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester, and others.
  • Page 203 Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks.
  • Page 204 Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
  • Page 205 Tires, Wheels and Loading TIRE CARE Improper or inadequate vehicle maintenance can also cause tires to wear abnormally. Here are some of the important maintenance items: Tire wear Measure and inspect the tire tread on all your tires periodically. Advanced and unusual tire wear can reduce the ability of tread to grip the road in adverse (wet, snowy, etc.) conditions.
  • Page 206 Tires, Wheels and Loading Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road •...
  • Page 207 Tires, Wheels and Loading Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by a qualified technician at a Ford or Lincoln/Mercury dealer. Front wheel drive (FWD) vehicles and those with an independent rear suspension (if equipped) may require alignment of all four wheels.
  • Page 208 Tires, Wheels and Loading • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (AWD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Ford or Lincoln/Mercury dealership to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.

  • Page 209: Vehicle Loading

    Tires, Wheels and Loading Follow these guidelines when using snow tires and chains: • Use only cable type chains offered by Ford as an accessory or equivalent. Using SAE class S or other conventional link type chains may cause damage to the vehicle’s wheel house and/or body. •...
  • Page 210 Tires, Wheels and Loading Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) –...
  • Page 211 Tires, Wheels and Loading GVW (Gross Vehicle Weight) – is the Vehicle Curb Weight + cargo + passengers. GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the driver’s...
  • Page 212 Tires, Wheels and Loading GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers –...
  • Page 213 Tires, Wheels and Loading 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kilograms or XXX pounds. 4. The resulting figure equals the available amount of cargo and luggage load capacity.

  • Page 214: Trailer Towing

    Tires, Wheels and Loading The above calculations also assume that the loads are positioned in your vehicle in a manner that does not overload the Front or the Rear Gross Axle Weight Rating specified for your vehicle on the Certification label found on the driver’s door.
  • Page 215 Tires, Wheels and Loading Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system.
  • Page 216 Tires, Wheels and Loading Trailer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. •...

  • Page 217: Recreational Towing

    Tires, Wheels and Loading RECREATIONAL TOWING (ALL WHEELS ON THE GROUND) Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground (such as behind a recreational vehicle). These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication.

  • Page 218: Driving

    Driving Driving STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engine and all accessories/locks the gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running.
  • Page 219 Driving Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately.
  • Page 220 Driving 5. Turn the key to 3 (ON) without turning the key to 4 (START). Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate.

  • Page 221: Brakes

    Driving Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again. If the engine still fails to start, press the accelerator to the floor and try again; this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel.
  • Page 222 Driving Refer to Brake system warning BRAKE light in the Instrument Cluster chapter for information on the brake system warning light. Four-wheel anti-lock brake system (ABS) Your vehicle is equipped with an Anti-lock Braking System (ABS). This system helps you maintain steering control during emergency stops by keeping the brakes from locking.
  • Page 223 Driving Parking brake with auto-release Apply the parking brake whenever the vehicle is parked. To set the parking brake: 1. Move the gearshift to P (Park). 2. Push pedal downward. The BRAKE warning lamp in the BRAKE instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is fully released.

  • Page 224: Traction Control

    Driving If the parking brake fails to release after completing this procedure, use the manual parking brake release lever. Pull the lever to manually release the parking brake. TRACTION CONTROL For Traction Control warning lights refer to Warning Lights in the Instrument cluster chapter.
  • Page 225 Driving Aggressive driving in any road conditions can cause you to lose control of your vehicle increasing the risk of severe personal injury or property damage. The occurrence of a Traction Control event is an indication that at least some of the tires have exceeded their ability to grip the road;...

  • Page 226: Air Suspension

    Driving If the amount of effort required to steer your vehicle changes while driving at a constant vehicle speed, have the power steering system checked by your dealer or a qualified service technician. AIR SUSPENSION SYSTEM The air suspension system is designed to improve ride, handling and general vehicle performance during: •...
  • Page 227 Driving If the fuse is not blown, perform the following procedure: 1. Apply the parking brake, turn the ignition to 2 (ACC). 2. Locate the access plug on the underside of the steering column cover. 3. Remove the access plug using a flat head screwdriver, then push and hold the override button using a flat head screwdriver.
  • Page 228 Driving Driving with a 4–speed automatic transmission Understanding the gearshift positions of the 4–speed automatic transmission P (Park) This position locks the transmission and prevents the rear wheels from turning. To put your vehicle in gear: • Start the engine •...
  • Page 229 Driving (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through four. Overdrive can be deactivated by pressing the transmission control switch on the gearshift lever. The transmission control indicator light (TCIL) will illuminate on the instrument cluster.
  • Page 230 Driving 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds. Forced downshifts • Allowed in (Overdrive) or Drive. •...
  • Page 231 Driving REVERSE SENSING SYSTEM The extended rear park aid system sounds a tone to warn the driver of obstacles near the rear bumper when the R (Reverse) gear is selected. To help avoid personal injury, please read and understand the limitations of the extended rear park assist system as contained in this section.
  • Page 232 Driving The system detects obstacles within approximately 16 feet (five meters), at speeds above 2 mph [3 km/h]) behind the rear bumper with a decreased coverage area at the outer corners of the bumper. If vehicle speed is below 2 mph (3 km/h), the system detects obstacles within approximately 10 feet (three meters) behind the rear bumper with a decreased coverage area at the outer corners of the bumper.
  • Page 233 Driving The OFF indicator remains illuminated when the system is disabled. The system defaults to ON every time the ignition is turned on. Press the control to disable or enable the system. The indicator will remain illuminated to indicate a failure of the extended rear park aid.

  • Page 234: Roadside Emergencies

    Roadside Emergencies Roadside Emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: •...

  • Page 235: Fuel Pump Shut-Off Switch

    Roadside Emergencies Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who need to obtain reimbursement information, call 1–800–665–2006.

  • Page 236: Fuses And Relays

    Roadside Emergencies The fuel pump shut-off switch is located on a bracket inside of the luggage compartment. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3.
  • Page 237 Roadside Emergencies Standard fuse amperage rating and color COLOR Cartridge Fuse Mini Standard Maxi Fuse link maxi rating fuses fuses fuses cartridge fuses Grey Grey — — — Violet Violet — — — Pink Pink — — — — — —...
  • Page 238 Roadside Emergencies The fuses are coded as follows. Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description Starter relay coil Restraint Control Module (RCM), Occupant Classification Sensor (OCS), Passenger Air bag Deactivation Indicator (PADI) Audio, Navigation control head Back-up lamps Audio Passive Anti-Theft System (PATS), Powertrain Control...

  • Page 239: Dual Automatic Temperature Control

    Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description Power Decklid Module (PDM), Lighting Control Module (LCM), Overdrive cancel switch, Cluster, Rear defroster relay coil 7.5A Mirror switch illumination, Door lock switch illumination, Rear audio control, Heated seat switch illumination, LCM, Electrochromatic mirror, Overhead console...
  • Page 240 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description LCM (High beams), Multi-function switch (Flash-to-pass) Brake-Transmission Shift Interlock (BTSI), Stop switch signal feed, Speed control deactivation switch LCM (Park lamps, cornering lamps) DATC module Center High-Mounted Stop Lamp (CHMSL) Turn signals Stop lamps...
  • Page 241 Roadside Emergencies The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Power Distribution Box Location Rating Description 20A* Ignition switch (Key in, RUN 1, RUN 2) 25A* Ignition switch (RUN/START, RUN/ACC, START) 10A* Powertrain Control Module (PCM) keep alive power 20A* Fuel relay feed 20A*...
  • Page 242 Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Location Rating Description 20A* Instrument panel fuse box feed #3 20A* Stop lamp switch 15A* Lumbar, Fuel door 20A* Heated seats – Not used – Not used 15A* Injectors 15A* PCM, Mass Air Flow (MAF) sensor 15A* Powertrain loads and sensors...

  • Page 243: Jump Starting

    Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Location Rating Description 30A** Driver seat module 20A** Rear heated seats K201 Micro relay A/C clutch K202 — Not used K203 Micro relay Ignition coil K204 Micro relay K205 — Not used K206 Micro relay Fuel...
  • Page 244 Roadside Emergencies Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start capability; doing so may damage the catalytic converter. Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts.
  • Page 245 Roadside Emergencies 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. REVIEW COPY 2005 Town Car (tow), Owners Guide (post-2002-fmt) (own2002), Market: USA_English (fus)
  • Page 246 Roadside Emergencies 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
  • Page 247 Roadside Emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2.
  • Page 248 Roadside Emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.

  • Page 249: Wrecker Towing

    Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.

  • Page 250: Customer Assistance

    Customer Assistance Customer Assistance GETTING THE SERVICES YOU NEED At home You must take your Lincoln or Mercury vehicle to an authorized Lincoln Mercury dealer for warranty repairs. While any Ford, Lincoln or Mercury dealership handling your vehicle line will provide warranty service, we recommend you return to your selling dealer who wants to ensure your continued satisfaction.
  • Page 251 Customer Assistance Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
  • Page 252 Customer Assistance In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws.
  • Page 253 Customer Assistance • available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
  • Page 254 Customer Assistance • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. What the Board needs To have your case reviewed you must complete the application in the DSB brochure and mail it to the address provided on the application...
  • Page 255 Customer Assistance before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. An oral presentation may be requested by the Board as well. Making a decision Board members review all available information related to each complaint, including oral presentations, and arrive at a fair and impartial decision.
  • Page 256 Customer Assistance The CAMVAP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings.
  • Page 257 Customer Assistance GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact a district or owner relations/customer relationship office.

  • Page 258: Reporting Safety Defects (U.s. Only)

    Customer Assistance For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.com. (Items in this catalog may be purchased by credit card, check or money order.) Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to...

  • Page 259: Cleaning

    Cleaning Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid.
  • Page 260 Cleaning PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jam) to your dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips.
  • Page 261 Cleaning • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer.
  • Page 262 Cleaning • Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. • Wiper blades can be cleaned with isopropyl (rubbing) alcohol or windshield washer solution. Be sure to replace wiper blades when they appear worn or do not function properly.
  • Page 263 Cleaning Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. Do not use chemical solvents or strong detergents when cleaning the seat-mounted side air bag. Such products could contaminate the side air bag system and affect performance of the side air bag in a collision.
  • Page 264 Cleaning FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.

  • Page 265: Maintenance And Specifications

    Maintenance and Specifications Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
  • Page 266 Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front of the hood in the grille.

  • Page 267: Engine Compartment

    Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L SOHC V8 engine 1. Brake fluid reservoir 2. Engine oil dipstick 3. Air filter assembly 4. Power steering fluid reservoir 5. Engine coolant reservoir 6. Battery 7. Windshield washer fluid reservoir 8.

  • Page 268: Engine Oil

    Maintenance and Specifications WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Refer to Refill capacities in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common...
  • Page 269 Maintenance and Specifications 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL.
  • Page 270 Maintenance and Specifications • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter. • Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by a qualified service technician.
  • Page 271 Maintenance and Specifications Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ISLAC), comprised of U.S.

  • Page 272: Battery

    Maintenance and Specifications BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules.
  • Page 273 Maintenance and Specifications When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
  • Page 274 Maintenance and Specifications • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. RECYCLE ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals listed in the Scheduled Maintenance Guide.
  • Page 275 Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application).
  • Page 276 Maintenance and Specifications Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container.
  • Page 277 Maintenance and Specifications remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure;...
  • Page 278 Maintenance and Specifications Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in this section.
  • Page 279 Maintenance and Specifications What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain.
  • Page 280 Maintenance and Specifications 2. Arrange for the vehicle to be taken to a service facility. 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap while the engine is running or hot.
  • Page 281 Maintenance and Specifications Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury.
  • Page 282 Maintenance and Specifications Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area).
  • Page 283 Maintenance and Specifications Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. Your vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based additives. Studies indicate that these additives can cause your vehicle’s emission control system to deteriorate more rapidly.
  • Page 284 Maintenance and Specifications Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: •...
  • Page 285 Maintenance and Specifications The advertised capacity is the amount of the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty.
  • Page 286 Maintenance and Specifications Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’s fuel economy under current driving conditions. Additionally, keeping records during summer and winter will show how temperature impacts fuel economy.
  • Page 287 Maintenance and Specifications • Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle scheduled maintenance guide. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed.
  • Page 288 Maintenance and Specifications • Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in your Scheduled Maintenance Guide performed according to the specified schedule. The scheduled maintenance items listed in the Scheduled Maintenance Guide are essential to the life and performance of your vehicle and to its emissions system.
  • Page 289 Maintenance and Specifications service technician in properly servicing your vehicle. When the Check engine/Service engine soon light illuminates, the OBD-II system has detected a malfunction. Temporary malfunctions may cause your Check engine/Service engine soon light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly.) 2.
  • Page 290 Maintenance and Specifications CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary, use only MERCON ATF. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).
  • Page 291 Maintenance and Specifications BRAKE FLUID RESERVOIR The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels below the “MAX” line that do not trigger the brake system warning lamp are within the normal operating range, there is no need to add fluid.
  • Page 292 Maintenance and Specifications Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is above 10°C (50°F). Correct fluid level The transmission fluid should be checked at normal operating temperature 66°C-77°C (150°F-170°F) on a level surface.
  • Page 293 Maintenance and Specifications High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used.

  • Page 294: Air Filter(S)

    Maintenance and Specifications Changing the air filter element 1. Release the clamps that secure the air filter housing cover. 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the air filter housing. 4.

  • Page 295: Refill Capacities

    Maintenance and Specifications For PCV valve replacement, see your dealer or a qualified service technician. Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the PCV valve. Replace the PCV valve with one that meets Ford material and design specifications for your vehicle, such as a Motorcraft or equivalent replacement part.
  • Page 296 Maintenance and Specifications Fluid Ford Part Name Capacity Fuel tank 71.9L (19.0 gallons) Rear axle lubricant Motorcraft SAE 80W-90 Premium Rear 2.4L (5.0 pints) Axle Lubricant Windshield washer Motorcraft Premium fluid Windshield Washer Fill to line on reservoir Concentrate Use only brake fluids certified to meet Ford specifications. Refer to Lubricant Specifications in this chapter.

  • Page 297: Lubricant Specifications

    Maintenance and Specifications LUBRICANT SPECIFICATIONS Item Ford part Ford part Ford name number specification Brake fluid Motorcraft High PM-1 ESA-M6C25-A Performance and DOT 3 DOT 3 Motor Vehicle Brake Fluid Door Silicone XL-6 ESR-M13P4-A weatherstrips Lubricant Engine coolant Motorcraft VC-7-A (U.S., WSS-M97B Premium Gold except CA and...
  • Page 298 Maintenance and Specifications Item Ford part Ford part Ford name number specification Rear Axle Motorcraft SAE XY-80W90-QL WSP-M2C197-A Lubricant 80W-90 Premium Rear Axle Lubricant Windshield Motorcraft ZC-32–A WSB-M8B16–A2 washer fluid Premium Windshield Washer Concentrate Use only brake fluids certified to meet Ford specifications. DOT 3 fluid is recommended.
  • Page 299 Maintenance and Specifications ENGINE DATA Engine 4.6L SOHC V8 engine Cubic inches Required fuel 87 octane Firing order 1-3-7-2-6-5-4-8 Ignition system Coil on plug Spark plug gap 0.052–0.056 inch (1.32–1.42mm) Compression ratio 9.4:1 VEHICLE DIMENSIONS Vehicle dimensions Inches (mm) (1) Overall length 215.4 (5471/221.4 (5623) (2) Overall width 78.5 (1993)
  • Page 300 Maintenance and Specifications REVIEW COPY 2005 Town Car (tow), Owners Guide (post-2002-fmt) (own2002), Market: USA_English (fus)
  • Page 301 Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the structure by the trailing edge of the driver’s door or the edge of the driver’s door.
  • Page 302 Maintenance and Specifications 1. World manufacturer identifier 2. Brake type and gross vehicle weight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped).

  • Page 303: Accessories

    Accessories Accessories LINCOLN ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Lincoln Accessories are available for your vehicle through your local authorized Lincoln or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
  • Page 304 Accessories Lifestyle Bike racks Cargo organization and management Peace of mind First aid and highway safety kits Full vehicle covers Locking gas cap Remote start Vehicle security systems For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: •...

  • Page 305: Index

    Index Index jumping a disabled battery ..243 maintenance-free ....272 Accessory delay ......115 replacement, specifications ...294 servicing ........272 Air bag supplemental restraint system ......166–167, 174 BeltMinder .........161 and child safety seats ....169 Brakes ........221 description ......167, 174 anti-lock ........222 disposal ........176 anti-lock brake system (ABS) driver air bag ....169, 175 indicator light ....174, 176...
  • Page 306 Index wiper blades ......261 Defrost rear window ......90 Climate control (see Air conditioning or Heating) ....87 Dipstick automatic transmission Clock ..........113 fluid ..........291 Compass, electronic engine oil .........268 set zone adjustment ....104 Doors Console lubricant specifications ..297 overhead ........102 rear ........121, 129 Driving under special conditions ........230 Controls...
  • Page 307 Index aiming ........93 autolamp system .......91 bulb specifications ....96 Fail safe cooling ......279 daytime running lights .....92 Floor mats .........130 flash to pass ......92 Fluid capacities ......295 high beam .........92 Fuel ..........280 replacing bulbs ......97 calculating fuel turning on and off ....91 economy ....106, 124, 284 Hood ..........266 cap ...........282...
  • Page 308 Index bulb replacement cd functions ......42 specifications chart ....96 destination mode ......65 daytime running light ....92 DVD location ......85 headlamps .........91 map mode .........46 headlamps, flash to pass ..92 quick start .........27 instrument panel, dimming ..93 radio functions ......34 interior lamps .....95–96, 100 replacing bulbs .....95, 97–99 Lane change indicator Octane rating ......283...
  • Page 309 Index Remote entry system Steering illuminated entry ....138 speed sensitive .......225 locking/unlocking doors ..135 Steering wheel opening the trunk ....136 controls ........120 Reverse sensing system ...231 tilting ........102 Roadside assistance ....234 Tilt steering wheel ....102 Safety Belt Maintenance ..166 Tires ......188–189, 193 alignment ........206 Safety belts (see Safety care ..........205...
  • Page 310 Index Water, Driving through .....233 Vehicle dimensions ....299 Windows Vehicle Identification Number power ........114 (VIN) ..........301 Windshield washer fluid and Vehicle loading ......209 wipers ........101 Ventilating your vehicle ...221 replacing wiper blades ...101 Wrecker towing ......249 Warning lights (see Lights) ..10 REVIEW COPY 2005 Town Car (tow), Owners Guide (post-2002-fmt) (own2002), Market: USA_English (fus)

Table of Contents

Save PDF