Gigabyte W270BUQ User Manual
  1. Manuals
  2. Brands
  3. Gigabyte Manuals
  4. Laptop
  5. W270BUQ
  6. User manual

Gigabyte W270BUQ User Manual

Notebook
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
V11.2.00

Advertisement

Table of Contents
loading

Related Manuals for Gigabyte W270BUQ

Summary of Contents for Gigabyte W270BUQ

  • Page 1 V11.2.00...
  • Page 3 Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.

  • Page 4: Eup-Standby And Off Mode Power Consumption Statement

    Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Direc- tive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Lux- embourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slov- enia.
  • Page 5 Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has at- tained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation.

  • Page 6: Fcc Statement

    Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

  • Page 7: Fcc Rf Radiation Exposure Statement

    Preface FCC RF Radiation Exposure Statement: This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

  • Page 8: Important Safety Instructions

    Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

  • Page 9: Instructions For Care And Operation

    Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer Do not place it on an unstable Do not place anything heavy...
  • Page 10 Preface Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work.

  • Page 11: Power Safety

    Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer.  • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, Power Safety Warning consult your service representative or local power company.

  • Page 12: Polymer Battery Precautions

    Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mecha- nism and is not a cause for concern.

  • Page 13: Battery Precautions

    Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.

  • Page 14: Cleaning

    Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock.

  • Page 15: Travel Considerations

    Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched.
  • Page 16 Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common.
  • Page 17 Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.

  • Page 18: Lcd Screen Care

    Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. •...

  • Page 19: Table Of Contents

    Preface Contents Notice .................I System Map: LCD Panel Open - Model A Design II ..1-8 EuP-Standby and Off Mode Power Consumption System Map: LCD Panel Open - Model A Design III ...1-9 Statement: .................II System Map: LCD Panel Open - Model B ....1-10 FCC Statement ..............
  • Page 20 Preface Optical (CD/DVD) Device ..........2-3 Resuming Operation ............3-9 Loading Discs ..............2-3 Energy Star Power Saving ...........3-10 Handling CDs or DVDs ..........2-4 Battery Information ............3-11 DVD Regional Codes ............2-5 Battery Power ..............3-11 Multi-In-1 Card Reader ..........2-6 Conserving Battery Power ...........3-12 Touchpad and Buttons/Mouse ........2-7 Battery Life ..............3-13 Gestures and Device Settings ........2-8 New Battery ..............3-13...
  • Page 21 Preface Audio ................4-6 Upgrading the Optical (CD/DVD) Device ....6-7 Windows Experience Index ...........4-7 Removing the Optical Device for Optional Drivers ............4-8 Model A Computers ............6-8 PC Camera Module ............4-8 Removing the Optical Device for Wireless LAN Module ...........4-8 Model B & C Computers ..........6-10 3.75G/HSPA Module .............4-8 Upgrading the System Memory (RAM) ......6-11 BIOS Utilities...
  • Page 22 Preface Creating a Profile ............7-37 Interface (Ports & Jacks) Choosing a Profile ............7-40 Overview ...............A-1 Editing a Profile ............7-41 Notebook Ports and Jacks ..........A-2 Text Messaging Service (SMS) ........7-42 Setting ................7-45 AMD Video Driver Controls Statistics & Information ..........7-51 Video Driver Installation ..........B-1 Wireless Manager ............7-52 Video (VGA) ..............
  • Page 23 Preface Audio ................C-3 Keyboard & Pointing Device ........C-3 Interface ................ C-3 Slots ................C-3 Card Reader ..............C-3 Communication ............. C-4 Power Management ............C-4 Power ................C-4 Security ................. C-4 Indicators ..............C-4 Design Feature .............. C-4 Operating System ............
  • Page 24 Preface XXII...

  • Page 25: Quick Start Guide

    Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: •...

  • Page 26: Advanced Users

    Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - “BIOS Utilities” on page 5 - 1 “Upgrading The Computer”...

  • Page 27: Not Included

    Quick Start Guide Not Included Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database pro- grams) have their own manuals, so please consult the appropriate manuals.  Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers &...

  • Page 28: System Startup

    Quick Start Guide System Startup Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.

  • Page 29: System Software

    Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find that this manual refers to the Windows 7 operating system with Service Pack 1 installed.

  • Page 30: Model Differences

    Quick Start Guide Model Differences This notebook series includes three different models that vary slightly in design style, color and general appear- ance (Model A has three distinct design styles as pictured on the following pages). Note that though your com- puter may look slightly different from that pictured throughout this manual, all ports, jacks and general functions are the same for all the design styles (see “Specifications”...

  • Page 31: System Map: Lcd Panel Open - Model A Design I

    Quick Start Guide System Map: LCD Panel Open - Model A Design I Figure 1 - 2 LCD Panel Open -  Model A Design I Wireless Device Built-In PC Camera Operation Aboard (Optional) Aircraft Power Button The use of any portable elec- Hot Key Buttons tronic transmission devices LED Status...

  • Page 32: System Map: Lcd Panel Open - Model A Design Ii

    Quick Start Guide System Map: LCD Panel Open - Model A Design II Figure 1 - 3 LCD Panel Open - Model A Design II  Built-in PC Camera Wireless Device Operation Aboard (Optional) Aircraft Power Button The use of any portable electronic LED Status transmission devices aboard air- craft is usually prohibited.

  • Page 33: System Map: Lcd Panel Open - Model A Design Iii

    Quick Start Guide System Map: LCD Panel Open - Model A Design III Figure 1 - 4 LCD Panel Open -  Model A Design III Wireless Device Built-In PC Camera Operation Aboard (Optional) Aircraft Power Button The use of any portable electronic transmission devices aboard air- Hot Key Buttons craft is usually prohibited.

  • Page 34: System Map: Lcd Panel Open - Model B

    Quick Start Guide System Map: LCD Panel Open - Model B Figure 1 - 5 LCD Panel Open Model B  Built-in PC Camera Wireless Device Operation Aboard (Optional) Aircraft Power Button The use of any portable electronic LED Status transmission devices aboard air- craft is usually prohibited.

  • Page 35: System Map: Lcd Panel Open - Model C

    Quick Start Guide System Map: LCD Panel Open - Model C Figure 1 - 6 LCD Panel Open Model C  Built-In PC Camera Wireless Device (Optional) Operation Aboard Aircraft Power Button LED Indicators The use of any portable electronic transmission devices aboard air- Keyboard craft is usually prohibited.

  • Page 36: Led Indicators

    Quick Start Guide LED Indicators Icon Color Description The LED indicators on the computer display helpful information about the current status of the computer. Icon Color Description Scroll Lock Activated (to activate Orange DC Power is Plugged In Green press Fn & Scr Lk) Green The Computer is On Green...

  • Page 37: Hot Key Buttons - Model A Design I Only

    Quick Start Guide Hot Key Buttons - Model A Design I Only These buttons give instant access to the default Internet browser and e-mail program, and allow you to toggle the Silent Mode on/off with one quick button press. Hot Key Function Toggle *Silent Mode (for power saving) Activate the Default Internet Program...

  • Page 38: Hot Key Buttons - Model A Design Iii Only

    Quick Start Guide Hot Key Buttons - Model A Design III Only These buttons give instant access to the default Internet browser and e-mail program, and allow you to toggle the WLAN module on/off with one quick button press. Hot Key Function Toggle WLAN Module On/Off Activate the Default Internet Program...

  • Page 39: Keyboard - Model A Designs I & Ii

    Quick Start Guide Keyboard - Model A Designs I & II  The keyboard has an embedded numerical keypad for easy numeric data input, and Other Keyboards features function keys to allow you to change operational features instantly. See Table 1 - 6, on page 1 - 18 for full function key combination details.

  • Page 40: Keyboard - Model A Design Iii

    Quick Start Guide Keyboard - Model A Design III  The keyboard has an embedded numerical keypad for easy numeric data input, and Other Keyboards features function keys to allow you to change operational features instantly. See Table 1 - 6, on page 1 - 18 for full function key combination details.

  • Page 41: Keyboard - Models B & C

    Quick Start Guide Keyboard - Models B & C  The keyboard has an embedded numerical keypad for easy numeric data input, and Other Keyboards features function keys to allow you to change operational features instantly. See Table 1 - 6, on page 1 - 18 for full function key combination details.

  • Page 42: Function/Hot Key Indicators

    Quick Start Guide Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed. Keys Function Keys...

  • Page 43: System Map: Front & Left Views

    Quick Start Guide System Map: Front & Left Views Figure 1 - 10 Front & Left Views Model A LED Power Indi- cators (see Table 1 - 2, on Models B & C page 1 - DC-In Jack External Monitor Model A Port RJ-45 LAN Jack...

  • Page 44: System Map: Right & Rear Views

    Quick Start Guide System Map: Right & Rear Views Figure 1 - 11 Right & Rear Views Model A Microphone-In Jack Headphone-Out Jack USB 2.0 Port Model B Optical Device Drive Bay (for CD/ DVD Device) Security Lock Slot Model C Battery ...
  • Page 45 Quick Start Guide   Changing DVD Regional Codes Disk Eject Warning Go to the Control Panel and double-click Device Don’t try to eject a CD/DVD while the system is ac- Manager (Hardware and Sound), then click the + cessing it. This may cause the system to “crash”. Stop next to DVD/CD-ROM drives.

  • Page 46: System Map: Bottom View - Model A

    Quick Start Guide System Map: Bottom View - Model A Figure 1 - 12 Bottom View - Model A Battery Component Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover 3.75G USIM Card Cover (Optional)  The CPU is not a user serviceable part.

  • Page 47: System Map: Bottom View - Model B

    Quick Start Guide System Map: Bottom View - Model B Figure 1 - 13 Bottom View - Model B Battery Component Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover 3.75G USIM Card Cover (Optional) Speakers  The CPU is not a user serviceable part.

  • Page 48: System Map: Bottom View - Model C

    Quick Start Guide System Map: Bottom View - Model C Figure 1 - 14 Bottom View - Model C Battery Component Bay Cover Fan Intake/Vent Hard Disk Bay Cover Speakers  Battery Information Always completely dis- charge, then fully  charge, a new battery before using it.

  • Page 49: Windows 7 Start Menu & Control Panel

    Quick Start Guide Windows 7 Start Menu & Control Panel Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are ac- cessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop.

  • Page 50: Video Features

    Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows 7. For more detailed video information see “AMD Video Driver Controls” on page B - 1.
  • Page 51 Quick Start Guide To access the AMD Vision Engine/Catalyst Control Center (See Appendix B for detailed information): Right-click the desktop and select AMD VISION Engine Control Center/Catalyst Control Center Double-click the icon in the Windows taskbar notification area (or right-click the icon and select AMD VISION Engine Control Center/Catalyst Control Center).
  • Page 52 Quick Start Guide Click the Preferences button and select either Advanced View or Standard View. The menu headings allow you to select which items you wish to change. Advanced View Standard View Figure 1 - 18 - AMD VISION Engine Control Center 1 - 28 Video Features...

  • Page 53: Power Options

    Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 23) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu.
  • Page 54 Quick Start Guide 1 - 30...

  • Page 55: Features & Components

    Features & Components Chapter 2: Features & Components Overview Read this chapter to learn more about the following main features and components of the computer: • Hard Disk Drive • Optical (CD/DVD) Device • Multi-In-1 Card Reader • Touchpad and Buttons/Mouse •...

  • Page 56: Hard Disk Drive

    Features & Components Hard Disk Drive  The hard disk drive is used to store your data in the computer. The hard disk can be Power Safety taken out to accommodate other serial (SATA) hard disk drives (see “Storage” on page C - 3 for specification information).

  • Page 57: Optical (Cd/Dvd) Device

    Features & Components Optical (CD/DVD) Device  There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de- Sound Volume vice will depend on the module you purchased (see “Storage” on page C - 3). The Adjustment optical device is usually labeled “Drive D:”...

  • Page 58: Handling Cds Or Dvds

    Features & Components Handling CDs or DVDs  Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be CD Emergency Eject accessed. If you need to manually eject a CD (e.g.

  • Page 59: Dvd Regional Codes

    Features & Components DVD Regional Codes To change the DVD regional codes: Go to the Control Panel Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.

  • Page 60: Multi-In-1 Card Reader

    Features & Components Multi-In-1 Card Reader  The card reader allows you to use some of the latest digital storage cards. Push the Card Reader Cover card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).

  • Page 61: Touchpad And Buttons/Mouse

    Features & Components Touchpad and Buttons/Mouse  The Touchpad is an alternative to the mouse; however, you can also add a mouse to Touchpad Scrolling your computer through one of the USB ports. The Touchpad buttons function in much the same way as a two-button mouse. This computer model se- ries may feature different Touchpad versions.

  • Page 62: Gestures And Device Settings

    Features & Components Gestures and Device Settings  The Synaptics Gestures Suite application allows you to use a specific gesture (ac- Show Video tion) on the surface of the Touchpad to perform specific actions to manipulate doc- uments, objects and applications. You can get a clearer view of the gestures in- You can configure the settings from the Device Settings tab in Mouse Properties:...
  • Page 63 Features & Components Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the Touchpad surface and slide both fingers in the direction required (in a straight con- Figure 2 - 7 tinuous motion).
  • Page 64 Features & Components Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the Touchpad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.

  • Page 65: Audio Features

    Features & Components Audio Features  You can configure the audio options on your computer from the Sound control Volume Adjustment panel in Windows, or from the Realtek HD Audio Manager icon in the notifi- cation area/control panel (right-click the notification area icon to bring up an au- The sound volume level is set using the volume...

  • Page 66: Setup For Audio Recording

    Features & Components Setup for Audio Recording To record audio sources on your computer at optimum quality follow the instruc- tions below: Click Start, and click Control Panel (or point to Settings and click Control Panel) and make sure you are in Classic View. Click Realtek HD Audio Manager (or right-click the notification area icon select Sound Manager).

  • Page 67: Adding A Printer

    Features & Components Adding a Printer  The most commonly used peripheral is a printer. The following conventions will Parallel Printer help you to add a printer; however it is always best to refer to the printer manual for specific instructions and configuration options. After setting up the print- er attach the parallel ca- USB Printer...
  • Page 68 Features & Components 2 - 14...

  • Page 69: Power Management

    Power Management Chapter 3: Power Management  Overview OS Note Power management To conserve power, especially when using the battery, your computer power man- functions will vary slight- agement conserves power by controlling individual components of the computer ly depending on your (the monitor and hard disk drive) or the whole system.

  • Page 70: The Power Sources

    Power Management The Power Sources  The computer can be powered by either an AC/DC adapter or a battery pack. Silent Mode (Model A AC/DC Adapter Design I Only) Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ Use the key to tog- DC adapter will damage the computer and its components.

  • Page 71: Turning On The Computer

    Power Management Turning On the Computer  Now you are ready to begin using your computer. To turn it on simply press the pow- Forced Off er button on the front panel. If the system “hangs”, When the computer is on, you can use the power button as a Stand by/Hibernate/ and the Ctrl + Alt + Del Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and key combination doesn’t...

  • Page 72: Power Plans

    Power Management Power Plans  The computer can be configured to conserve power by means of power plans. You Resuming can use (or modify) an existing power plan, or create a new one. Operation The settings may be adjusted to set the display to turn off after a specified time, and Table 3 - 1, on to send the computer into Sleep after a period of inactivity.
  • Page 73 Power Management Each Windows power plan will also adjust the processor performance of your ma- chine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is pow- ered from an AC power source.

  • Page 74: Power-Saving States

    Power Management Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps.

  • Page 75: Hibernate

    Power Management Hibernate  Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a Silent Mode power failure occurs the system can restore your work from the hard disk; if a power (Model A Design I Only) failure occurs when work is saved only to memory, then the work will be lost.

  • Page 76: Configuring The Power Buttons

    Power Management Configuring the Power Buttons  The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the Password computer in to a power-saving state. Click Choose what the power buttons do on Protection the left menu in Power Options to bring up the menu.

  • Page 77: Resuming Operation

    Power Management Resuming Operation  You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Closing the Lid Power Status To Resume Icon Color If you have chosen to send the computer to Power Off Press the Power Button...

  • Page 78: Energy Star Power Saving

    Power Management Energy Star Power Saving  This system supports Energy Star power management features that place comput- ers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period Notification Area of inactivity. If you want to enable Energy Star power saving then follow these in- Icon structions: If the notification area...

  • Page 79: Battery Information

    Power Management Battery Information  Follow these simple guidelines to get the best use out of your battery. Low Battery Battery Power Warning Your computer’s battery power is dependent upon many factors, including the pro- When the battery is criti- grams you are running, and peripheral devices attached.

  • Page 80: Conserving Battery Power

    Power Management Conserving Battery Power  • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. Windows Mobility Center • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter.

  • Page 81: Battery Life

    Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to re- move the battery for any reason see “Removing the Battery”...

  • Page 82: Proper Handling Of The Battery Pack

    Power Management Proper handling of the Battery Pack  • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode Caution • DO NOT connect the metal terminals (+, -) to each other Danger of explosion if battery is incorrectly re- placed.

  • Page 83: Battery Faq

    Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
  • Page 84 Power Management Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings. Figure 3 - 9 Change Plan Settings / Change Advanced Power Settings 3 - 16 Battery Information...
  • Page 85 Power Management Scroll down to Battery and click + to expand the battery options. Choose the options below (click Yes if a warning appears): Figure 3 - 10 Power Options Advanced Settings - Battery • Low battery levels = 0% •...
  • Page 86 Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.

  • Page 87: Drivers & Utilities

    Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the lat- est versions of most available operating systems haven’t built in drivers and utilities.

  • Page 88: Driver Installation

    Drivers & Utilities Driver Installation Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in Insert the Device Drivers & Utilities + User’s Manual this order) which is the same as that listed in the disc and click Install Drivers (button), or Option Driv- Drivers Installer menu below.
  • Page 89 Drivers & Utilities Driver Win 7 Driver Win 7 Video (VGA) Page 4 - 5 PC Camera Module Page 7 - 2 Page 4 - 6 Wireless LAN Module Page 7 - 10 CardReader Page 4 - 6 Bluetooth & Wireless LAN Combo Module Page 7 - 16 TouchPad Page 4 - 6...

  • Page 90: Updating/Reinstalling Individual Drivers

    Drivers & Utilities Updating/Reinstalling Individual Drivers User Account Control If you wish to update/reinstall individual drivers it If a User Account Control prompt appears as part of may be necessary to uninstall the original driver.To do the driver installation procedure, click Continue or this go to the Control Panel in the Windows OS and Allow, and follow the installation procedure as direct- double-click the Programs and Features icon (Pro-...

  • Page 91: New Hardware Found

    Drivers & Utilities New Hardware Found Driver Installation Procedure If you see the message “New Hardware Found” dur- Insert the Device Drivers & Utilities + User’s Manual ing the installation procedure (other than when out- disc and click Install Drivers (button). lined in the driver install procedure), click Cancel Video (VGA) to close the window, and follow the installation proce-...

  • Page 92: Lan

    Drivers & Utilities Audio 1. Click 2.Install LAN Driver > Yes. 1. Click 6.Install Audio Driver > Yes. 2. Click Install > Finish. 2. Click Next. 3. Click the button to agree to the license agree- CardReader ment and click Next. 1.

  • Page 93: Windows Experience Index

    Drivers & Utilities Windows Experience Index  After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experi- Windows Update ence Index (make sure the AC/DC adapter is plugged After installing all the drivers make sure you enable Win- in): dows Update in order to get all the latest security up- 1.

  • Page 94: Optional Drivers

    Drivers & Utilities Optional Drivers PC Camera Module See the pages indicated for the driver installation pro- See the introduction in “PC Camera Module” on cedures for any modules included in your purchase op- page 7 - 2, and check the installation procedure. tion.

  • Page 95: Bios Utilities

    BIOS Utilities Chapter 5: BIOS Utilities  Overview BIOS Screens Note that BIOS This chapter gives a brief introduction to the computer’s built-in software: screens pictured these pages are intend- If your computer has never been set up, or you are making important changes to the ed for guidance in set- system (e.g.

  • Page 96: The Setup Utility

    BIOS Utilities The Setup Utility  Each time you turn on the computer the system takes a few seconds to conduct a BIOS Settings POST, including a quick test of the on-board RAM (memory). Warning As the POST proceeds, the computer will tell you if there is anything wrong. If there Incorrect settings can is a problem that prevents the system from booting, it will display a system summary cause your system to...

  • Page 97: Failing The Post

    BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non- fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.

  • Page 98: Setup Screens

    BIOS Utilities Setup Screens  The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a Setup Menus new screen appears. Scroll through the features listed on each screen to make chang- Setup menus es to Setup.

  • Page 99: Main Menu

    BIOS Utilities Main Menu Figure 5 - 2 Main Menu System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings.
  • Page 100 BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.

  • Page 101: Advanced Menu

    BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu Advanced Chipset Control (Advanced Menu) The sub-menu here allows you to adjust the Bluetooth Power Setting. Advanced Menu 5 - 7...
  • Page 102 BIOS Utilities Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control)  You can adjust the Bluetooth module power setting to your preference. The default setting (Disabled) will see the Bluetooth module powered off when the system is SATA Mode started up or restarted.
  • Page 103 BIOS Utilities Boot Logo (Advanced Menu) Use this menu item to enable/disable the Boot Logo screen at system startup. If you disable the Boot Logo you will not see the F2 Enter Setup or F7 Boot Options prompts on the screen, however you can still press these keys, while the boot sceen is displayed, to perform the Enter Setup or Boot Option functions.

  • Page 104: Security Menu

    BIOS Utilities Security Menu  Security Menu The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your...
  • Page 105 BIOS Utilities Note: To clear existing passwords press Enter and type the existing password, then  press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance. Password Warning If you set a boot pass- word (Password on boot is “Enabled“), NEVER forget your password.

  • Page 106: Boot Menu

    BIOS Utilities Boot Menu Figure 5 - 5 Boot Menu  BIOS Screens Note that BIOS screens pictured these pages are intend- ed for guidance in set- ting up your system’s BIOS. BIOS versions are sub- ject to constant change and revision, therefore your computer’s actual When you turn the computer on it will look for an operating system (e.g.
  • Page 107 BIOS Utilities Boot Sequence (Boot Menu) Use the arrow keys to move up and down the menu and use the F5 and F6 keys to move the device’s boot priority up and down the list (the selected device will be highlighted in white).

  • Page 108: Exit Menu

    BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will re- turn the Setup to its original state, and erase any previous changes you have made in a previous session.

  • Page 109: Upgrading The Computer

    Upgrading The Computer Chapter 6: Upgrading The Computer Overview  This chapter contains information on upgrading the computer. Follow the steps out- Warranty Warning lined to make the desired upgrades. If you have any trouble or problems you can con- tact your service representative for further help.

  • Page 110: When Not To Upgrade

    Upgrading The Computer When Not to Upgrade  These procedures involve opening the system’s case, adding and sometimes replac- ing parts. Power Safety Warning You should not perform any of these upgrades if: Before you undertake • Your system is still under warranty or a service contract upgrade proce- •...

  • Page 111: Removing The Battery

    Upgrading The Computer Removing the Battery  If you are confident in undertaking upgrade procedures yourself, for safety reasons Warranty Warning it is best to remove the battery. Turn the computer off, and turn it over. Please check with your Slide the latch in the direction of the arrow.

  • Page 112: Upgrading The Hard Disk Drive

    Upgrading The Computer Upgrading the Hard Disk Drive  The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard HDD System disk drives with a height of 9.5mm (h) (see “Storage” on page C - 3).
  • Page 113 Upgrading The Computer Turn off the computer, and turn it over and remove the battery. Locate the hard disk bay cover and loosen screws & Remove the hard disk bay cover Model A Model B Figure 6 - 2 Hard Disk Bay Cover Removal Model C Upgrading the Hard Disk Drive 6 - 5...
  • Page 114 Upgrading The Computer Grip the tab and slide the hard disk in the direction of arrow  Lift the hard disk out of the bay Remove the screw(s) and the adhesive cover Hard Disk Screws & Reverse the process to install a new hard disk drive (do not forget to replace all the Cover screws and covers) The hard disks and cov-...

  • Page 115: Upgrading The Optical (Cd/Dvd) Device

    Upgrading The Computer Upgrading the Optical (CD/DVD) Device The procedure for removing the optical device will depend upon your particular computer model: • See “Removing the Optical Device for Model A Computers” on page 6 - • See “Removing the Optical Device for Model B & C Computers” on page 6 - Upgrading the Optical (CD/DVD) Device 6 - 7...

  • Page 116: Removing The Optical Device For Model A Computers

    Upgrading The Computer Removing the Optical Device for Model A Computers  Turn off the computer, and turn it over and remove the battery. Locate the component bay cover and remove screws Fan Cable & Cover Carefully (a fan and cable are attached to the under side of the cover) lift up Make sure you recon- the bay cover.
  • Page 117 Upgrading The Computer Remove the screw at point , and use a screwdriver to carefully push out the optical device at point Reverse the process to install the new device. Figure 6 - 5 Removing the Optical Device (Model A Computers) Upgrading the Optical (CD/DVD) Device 6 - 9...

  • Page 118: Removing The Optical Device For Model B & C Computers

    Upgrading The Computer Removing the Optical Device for Model B & C Computers Turn off the computer, and turn it over and remove the battery. Remove the hard disk (see page Remove the screw at point , and use a screwdriver to carefully push out the optical device at point Reverse the process to install the new device.

  • Page 119: Upgrading The System Memory (Ram)

    Upgrading The Computer Upgrading the System Memory (RAM)  Model A & B computers have one memory socket, and Model C computers have Fan Cable & Cover two memory sockets, for 204 pin Small Outline Dual In-line (SO-DIMM) DDRIII (DDR3) type memory modules (see “Memory”...

  • Page 120: Model A

    Upgrading The Computer Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover (note that for Model C computers you need to raise the bottom cover up to an angle of LESS THAN 30°). Carefully disconnect the fan cable , and remove the cover Model A...
  • Page 121 Upgrading The Computer Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( & Figure 6 - Figure 6 - 9 RAM Module Release  The RAM module will pop-up, and you can remove it.
  • Page 122 Upgrading The Computer 11. Replace the bay cover by (for Model C computers make sure you insert the  cover at an angle of LESS THAN 30° ) aligning the cover pins (see sidebar - make sure you reconnect the fan cable before screwing down the bay cover). Cover Pins 12.

  • Page 123: Modules & Options

    Modules & Options Chapter 7: Modules & Options  Overview Wireless Device Operation Aboard Aircraft This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please The use of any portable contact your service representative.

  • Page 124: Pc Camera Module

    Modules & Options PC Camera Module  Before installing the PC Camera driver, make sure that the optional PC Camera is Latest PC Camera on. Use the Fn + F10 key combination (see “Function/Hot Key Indicators” on Driver Information page 1 - 18) to toggle power to the PC Camera module.

  • Page 125: Pc Camera Driver Installation

    Modules & Options PC Camera Driver Installation  1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. PC Camera Screen 2. Click Option Drivers (button). Refresh 3.
  • Page 126 Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound).
  • Page 127 Modules & Options Figure 7 - 1 Audio Setup for PC Camera Right-click PC Camera Module 7 - 5...
  • Page 128 Modules & Options Camera Application The camera application is a video viewer for general purpose video viewing and test- ing, and for capturing video files to .avi format. Run the camera application from the desktop shortcut (it is recommended that you set the capture file before the capture process - see Set Capture File below).
  • Page 129 Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties).
  • Page 130 Modules & Options Eliminating Screen Flicker  If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options. Latest PC Camera Driver Information Run the camera application from the desktop shortcut. Go to Options and scroll down to select Video Capture Filter..
  • Page 131 Modules & Options Taking Still Pictures  The camera application allows you to take still pictures. Snapshot Folder Run the camera application from the desktop shortcut. Go to Options and select Take Picture. The Snapshot folder’s The picture (in JPEG format) will be placed in the Snapshot folder on the default location is on the desktop.

  • Page 132: Wireless Lan Module

    Modules & Options Wireless LAN Module  If you have included a Wireless LAN (or WLAN & Bluetooth combo) module in Wireless Device your purchase option, make sure that the module is on before installing the driver. Operation Aboard Aircraft Use the Fn + F11 key combination (see “Function/Hot Key Indicators”...

  • Page 133: 802.11B/G/N Driver Installation

    Modules & Options 802.11b/g/n Driver Installation If you see the message “Found New Hardware” click Cancel to close the window. 1. Make sure the module is powered on, then insert the Device Drivers & Util- ities + User’s Manual disc into the CD/DVD drive. 2.

  • Page 134: Connecting To A Wireless Network In Windows 7

    Modules & Options Connecting to a Wireless Network in Windows 7  Make sure the Wireless LAN module is turned on. Network and Click the notification area wireless icon , and then double-click an access point Sharing Center to connect to or click to Open Network and Sharing Center if you do not see a network you want to connect to in the notification area menu (a list of options will You can also use the Net- appear allowing setting changes, and creating a new network).
  • Page 135 Modules & Options You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click “View or change settings in Network and Sharing Center” to access further options for the connection.
  • Page 136 Modules & Options Click the notification area icon to see any currently connected networks.  To disconnect from the wireless network you can click the notification area wireless icon , click the active connection and then click Disconnect (button). Security Enabled Networks You should try to make sure that any network you are...

  • Page 137: Windows Mobility Center

    Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: Click Start, and click Control Panel (or point to Settings and click Control Panel).

  • Page 138: Bluetooth & Wireless Lan Combo Module

    Modules & Options Bluetooth & Wireless LAN Combo Module  If your purchase option includes the V3.0 Bluetooth Combination & Wireless Wireless Device LAN module then install the driver as instructed overleaf. Operation Aboard Aircraft Use the Fn + F12 key combination to toggle power to the Bluetooth module. When the Bluetooth module is powered on the indicator will briefly be dis- The use of any portable...

  • Page 139: 3Rd Party Bluetooth Combo Driver Installation

    Modules & Options 3rd Party Bluetooth Combo Driver Installation  Note this driver is required for the 3rd Party combo Bluetooth and WLAN module only. High Speed Bluetooth Data Transfer 1. Before installing the driver make sure the Bluetooth module is powered The Combination Wire- on (use Fn + F12 key combination), then insert the Device Drivers &...

  • Page 140: Bluetooth & Wlan Combo Settings

    Modules & Options Bluetooth & WLAN Combo Settings  Make sure the Bluetooth module is powered on. Bluetooth Module & Double-click the My Bluetooth application on the desktop (or access it from the Resuming From Sleep Programs/All Programs menu). Mode Click My Bluetooth Settings (menu heading).
  • Page 141 Modules & Options Click General Settings to change the computer name that other Bluetooth devices will see, and click the tickbox to Allow Bluetooth devices to find this computer Click OK to confirm the settings. Figure 7 - 8 General Settings Bluetooth &...
  • Page 142 Modules & Options Click File Transfer Settings to Enable sharing of my files with other Bluetooth devices. Click OK to confirm the settings. Figure 7 - 9 File Transfer Settings 7 - 20 Bluetooth & Wireless LAN Combo Module...

  • Page 143: Bluetooth Networking Setup

    Modules & Options Bluetooth Networking Setup Make sure the Bluetooth module is powered on. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu). Click My Bluetooth Settings (see Figure 7 - 7 on page 7 - 18).

  • Page 144: Bluetooth & Wlan Combo Module Configuration

    Modules & Options Bluetooth & WLAN Combo Module Configuration  Setup your Bluetooth Device so the Computer Can Find it Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Bluetooth Module & Make the device discoverable (to do this check your device documentation). Resuming From Sleep Mode To Turn the Bluetooth Module On...
  • Page 145 Modules & Options You will then be presented with a menu of options to select from. Figure 7 - 12 Bluetooth Device Options Click the appropriate button to connect to the device. Bluetooth & Wireless LAN Combo Module 7 - 23...
  • Page 146 Modules & Options You may need to allow the connection from your device, and you will then need to provide a passcode from the device. You can then enter the passcode on the computer and click OK to establish the connection.

  • Page 147: Standard Bluetooth Configuration In Windows 7

    Modules & Options Standard Bluetooth Configuration in Windows 7  Setup your Bluetooth Device so the Computer Can Find it Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Add a Device Make the device discoverable (to do this check your device documentation). Click Start, and click Con- trol Panel and then click To Turn the Bluetooth Module On...
  • Page 148 Modules & Options To Add a Bluetooth Device  Access the Bluetooth Devices control panel and click Add a device. Double-click the device you want to pair with the computer. Pairing Options If a device has been pre- viously connected then the pairing option menu will appear when you at- tempt subsequent con-...
  • Page 149 Modules & Options Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing.  Figure 7 - 16 Pairing Codes Pairing Code Example The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection proce- dure, and may require you to confirm a pairing code is correct on both devices.
  • Page 150 Modules & Options To Change Settings for the Bluetooth Device  Click the notification area icon and select Show Bluetooth Devices. Right-click on the device you want to change and click Properties to: Bluetooth Help • Change the name of the device (click Bluetooth, type a new name and click OK). •...

  • Page 151: 3.75G/Hspa Module

    Modules & Options 3.75G/HSPA Module  If you have included an optional (not supported by Model C computers) 3.75G/ HSPA (High Speed Packet Access) module (see “Communication” on page C - 4 3.75G/HSPA Module Options for specification details) in your purchase option, you will have the appropriate ap- plication (BandLuxe HSDPA Utility or Wireless Manager) provided for your par- There are two optional ticular module.
  • Page 152 Modules & Options Turn off the computer, and turn it over and remove the battery (see page Locate the 3.75G USIM card cover and loosen screw , and then remove the USIM card cover Figure 7 - 19 USIM Card Cover Removal ...
  • Page 153 Modules & Options Lock the SIMLOCK by pushing it in the direction of the arrow in Figure 7 - 21 until it clicks into the lock position. Figure 7 - 21 SIMLOCK Lock  3.75G/HSPA Modules & System Wake Up Note that the 3.75G modules DO NOT sup- port system wake up on...
  • Page 154 Modules & Options Before installing the application, make sure that the 3.75G/HSPA module is ON (installing the driver with the module off will not allow the software to detect the module hardware correctly). Use the Fn + key combination (see Table 1 - 6, on page 1 - 18) to toggle power to the 3.75G/HSPA module.

  • Page 155: Bandluxe Hsdpa Utility

    Modules & Options BandLuxe HSDPA Utility  With the 3.75G/HSPA module and USIM card (supplied by your service provider) installed you may then install the BandLuxe HSDPA Utility. The BandLuxe HS- Wireless Device DPA Utility allows you to directly access your HSPA internet service from the com- Operation Aboard puter.

  • Page 156: Bandluxe Hsdpa - Connection Manager

    Modules & Options BandLuxe HSDPA - Connection Manager The connection information is stored on the USIM card supplied by the service pro- vider (where this is not the case you may need to create a profile - see “Creating a Profile”...
  • Page 157 Modules & Options The system will connect to your network (you may need to set your network connection to home, work or public on the first connection). The connected icon will appear at the top of the utility screen. Figure 7 - 23 Connected You can then access the internet, download e-mail etc.
  • Page 158 Modules & Options While you are connected the notification area icon will display the connected icon , and the notification area will display the connected icon Figure 7 - 25 Notification Area Icon (Connected) To disconnect from the service provider, click the Disconnect icon, or click the close icon at the top right of the utility, and click Yes to confirm.

  • Page 159: Creating A Profile

    Modules & Options Creating a Profile Access the Connection Manager from the Start menu (Connection Manager ), or (Start > Programs/All Programs > BandLuxe > BandLuxe HSDPA Utility R11 > Connection Manager). Click the Menu > Profile. Figure 7 - 26 Menu - Profile The default profile will display the service provider’s name from the USIM card.
  • Page 160 Modules & Options Click New (button) and input any Network Settings required by your service  provider (all fields may not need to be filled in). The profile name is used to identify your profile if a number of profiles are used. Password You will need to check with your service provider to confirm if the User Name and Password are required.
  • Page 161 Modules & Options Click the newly created profile in the profile window and then click Default (button)  to set the profile as the default connection (note that only one profile may be stored as the default connection). 10. The newly created profile will now be stored as the default connection when you New SIM Card click Connect in the Connection Manager Home screen.

  • Page 162: Choosing A Profile

    Modules & Options Choosing a Profile If you need to switch stored profiles follow the instructions below: Access the Connection Manager from the Start menu (Connection Manager ), or (Start > Programs/All Programs > BandLuxe > BandLuxe HSDPA Utility R11 > Connection Manager). Click the Menu >...

  • Page 163: Editing A Profile

    Modules & Options Editing a Profile  If you need to edit stored profiles follow the instructions below: Get the Latest Access the Connection Manager from the Start menu (Connection Manager Access Point Name ), or (Start > Programs/All Programs > BandLuxe > BandLuxe Database HSDPA Utility R11 >...

  • Page 164: Text Messaging Service (Sms)

    Modules & Options Text Messaging Service (SMS)  In addition to standard internet services you may also send and receive SMS text messages using the Connection Manager, if your service supports SMS. Incoming Messages Inbox If the program is open The Inbox will contain any received SMS.
  • Page 165 Modules & Options Sent  The Sent folder contains any successfully sent SMS. Select the message and press the Delete to erase the record. Contact List Types Outbox Select a contact The Outbox folder contains any completed but unsent SMS. Select the message and from the SIM card.
  • Page 166 Modules & Options Template A template can store text that is used regularly in messages, and can be easily insert- ed in to any new SMS. Click Template (button) to view any stored templates. Click to highlight a template and click Select (button) to insert it into the message. Click New (button) to create a new template, and Save (button) to add it to the existing list.

  • Page 167: Setting

    Modules & Options Setting  The Setting menu allows you to edit the programs basic parameters. Access the Connection Manager from the Start menu (Connection Manager Language ), or (Start > Programs/All Programs > BandLuxe > BandLuxe The Connection Manager HSDPA Utility R11 >...
  • Page 168 Modules & Options SMS - Preference Click the New SMS Notify checkbox to be automatically notified when a new SMS arrives. If enabled a the incoming message notification will appear in the notification area, and an envelope icon will appear in the upper left corner of the Home screen Figure 7 - 36 Incoming SMS Notification...
  • Page 169 Modules & Options This menu allows you to edit the USIM card Personal Identification Number (PIN) and Enable/Disable the PIN if necessary. Press Apply after making any changes. A SIM card must be inserted for this function to be activated. Figure 7 - 38 Setting - SIM If a PIN code is enabled, the input will be requested during USIM card initialization.
  • Page 170 Modules & Options Radio Set the appropriate network search options from the dual mode setting menu. Click Apply (button) after making any changes. Figure 7 - 39 Setting - Radio Note: 2G/3G/3.5G data transferring will be disconnected when you apply a new Ra- dio setting.
  • Page 171 Modules & Options Network - Network Selection  Edit the network selection settings from this menu. The Standard (auto) setting will search for networks in the order specified in the Prefer list. Click Standard (auto) Network Setting > Next to view and adjust the Prefer list. The Prefer list is displayed at the top of the Note that the network set- screen, and the bottom of the screen lists all available networks.
  • Page 172 Modules & Options The Manual setting allows you to choose a network from all available. Click Man- ual > Next to view the list. Click to highlight a network from the list, and click Se- lect (button) to choose the network, or Cancel (button) to make no change. Figure 7 - 41 Setting - Network Manual...

  • Page 173: Statistics & Information

    Modules & Options Statistics & Information The Statistics screen displays a graph of recent upload and download activity. No data will be displayed if there is no current connection. Access the Connection Manager from the Start menu (Connection Manager ), or (Start > Programs/All Programs > BandLuxe > BandLuxe HSDPA Utility R11 >...

  • Page 174: Wireless Manager

    Modules & Options Wireless Manager  With the 3.75G/HSPA module and USIM card (supplied by your service provider) installed you may then install the Wireless Manager application. The Wireless Wireless Device Manager application allows you to directly access your HSPA internet service from Operation Aboard Aircraft the computer.

  • Page 175: Wireless Manager Application

    Modules & Options Wireless Manager Application  The connection information is stored on the USIM card supplied by the service pro- vider (where this is not the case you may need to create a profile - see “Creating a PIN Number Profile”...
  • Page 176 Modules & Options The system will connect to your network.  Connected will appear above the timer icon (the timer will indicate your connected time for the current session) Wireless Manager You can then access the internet, download e-mail etc. as per any internet Help connection.
  • Page 177 Modules & Options Click the Wireless Manager notification area icon to view the connection status, or wireless icon to view the Mobile Broadband Connection status Figure 7 - 45 Notification Area Icons (Connected)  Notification Area The indicator will display the signal strength and radio access Icon technology.

  • Page 178: Profiles

    Modules & Options Profiles Access the Wireless Manager application from the Start menu (Start > All Pro- grams > Wireless Manager > Wireless Manager) or the desktop shortcut Click the Settings > Advanced. Click the Profiles (tab). Figure 7 - 46 Advanced Settings - Profiles 7 - 56 3.75G/HSPA Module...
  • Page 179 Modules & Options Multiple profiles may be available from the USIM card and the first time the application starts it may require you to select a profile (Set Profile) to use for your connection. Figure 7 - 47 Multiple Profiles Found Automatic Profile Selection If Automatic selection is chosen, then the application will search the operator pro-...
  • Page 180 Modules & Options Selecting a Profile Click Manual selection (button). Click the Filter to view the drop-down list. Select the Profile you wish to use and click Apply to confirm the selection. Figure 7 - 48 Profile - Manual Selection (Filter) 7 - 58 3.75G/HSPA Module...
  • Page 181 Modules & Options Creating a Profile  Click Manual selection (button). Click the New. Deleting a Profile Enter a name you prefer for the profile. Enter the Access Point Name (APN). To delete a profile click Enter the User Name and Password if required (some service providers may not to select Manual selec- require this information and the fields may then be left blank).

  • Page 182: Settings

    Modules & Options Settings The Settings tab allows you at adjust the application features. Click to put a tick in Launch Wireless Manager at Windows startup to launch the application at Win- dows Startup. Figure 7 - 50 Settings The Advanced settings allows more detailed configuration. To access the Ad- vanced settings: Access the Wireless Manager program from the Start menu (Start >...
  • Page 183 Modules & Options  Most USIM cards are protected by a Personal Identity Number (PIN). You may turn on or off the Request PIN at startup (click Apply to save any changes). You can PIN Notes also Change PIN (you will need to enter the new PIN in the two fields provided and click Apply to save any changes).
  • Page 184 Modules & Options Networks  The mobile network list lists available networks at your location, and allows you to select a network which to connect. You must disconnect before being able to select Warning a network. Note that some applica- tions automatically Connection...

  • Page 185: Text Messaging Service (Sms)

    Modules & Options Text Messaging Service (SMS) In addition to standard internet services you may also send and receive SMS text messages using the Wireless Manager, if your service supports SMS. SMS Utility Access the Wireless Manager application from the Start menu (Start > All Pro- grams >...
  • Page 186 Modules & Options Messages Click the Messages tab to access the tabs displaying text messages. The tabs at the top of the menu display the Inbox, Drafts, Outbox, Sent and Trash menus. Inbox Drafts Outbox Sent Trash Figure 7 - 54 SMS Utility Messages Text messages are automatically saved to your computer and may be sorted in as-...

  • Page 187: Sending A Text Message

    Modules & Options Sending a Text Message Access the Wireless Manager application from the Start menu (Start > All Pro- grams > Wireless Manager > Wireless Manager) or the desktop shortcut Click SMS and the SMS Utility will then start. Click the New Message tab.
  • Page 188 Modules & Options Click Send to send the message or Save to save the message in the Drafts folder. Clicking the Clear icon clears both the Message and To fields. If radio is on then the message will be sent, however if the radio is off the message will be stored in the Outbox.
  • Page 189 Modules & Options Messages • Opening a text message: Double-click the message and the message will open in a new window (to close it click the close icon in the top right of the message). Figure 7 - 57 Click to close the message Close Message •...

  • Page 190: Phonebook

    Modules & Options Phonebook The Phonebook allows you to view and edit all your frequently used contacts, and is divided into Contacts and Groups . To access the Phonebook: Access the Wireless Manager application from the Start menu (Start > All Pro- grams >...
  • Page 191 Modules & Options Contacts  • New Contact: Click the New contact button to create a contact. Add the name and at least one phone number (Mobile, Work, Home and Other Import/Export fields are available) for the contact. Click the icon to expand the number Contacts details.
  • Page 192 Modules & Options Groups You can organize existing contacts into groups from the Groups tab. • New Group: Click the New group button to create a group. Click icon to expand the group details, and click a check box to add at least one phone number from the contacts for the group.

  • Page 193: Sms Settings

    Modules & Options SMS Settings The SMS Utility Settings tab allows you at adjust the SMS features. Figure 7 - 61 SMS Utility Settings  SMS Settings Message Length: You can set the number of blocks that can be sent (up to a length of 10 blocks).
  • Page 194 Modules & Options Send Click Delivery Report to automatically request a reply from a recipient. If you click to Send messages in Outbox automatically upon connection then messages writ- ten when the radio is off, will then be sent automatically the next time radio is turned on.
  • Page 195 Modules & Options Number You can choose to Use default service center number or you can uncheck the box and add your number manually if your service provider supplies a different number (click Apply to save the change or Default to return to the default number). Memory Phonebook memory status displays the number of contacts displayed on the USIM card.
  • Page 196 Modules & Options 7 - 74...

  • Page 197: Troubleshooting

    Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.

  • Page 198: Basic Hints And Tips

    Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer ap- pears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working.

  • Page 199: Backup And General Maintenance

    Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wal- let.

  • Page 200: Viruses

    Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini- tions file updates are usually downloadable directly from the internet.

  • Page 201: Upgrading And Adding New Hardware/Software

    Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.
  • Page 202 Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. •...

  • Page 203: Problems And Possible Solutions

    Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t Battery missing / incorrectly installed. Check the battery bay, make sure the work. battery is present and seated properly (the design of the battery only allows it to go in one way).
  • Page 204 Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating”...
  • Page 205 Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help.  Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
  • Page 206 Troubleshooting Problem Possible Cause - Solution I am sliding my finger up and down on the There are different Touchpad versions available on this computer, and this right side of the Touchpad to scroll a version requires tapping/holding to scroll. Either tap repeatedly, or hold the Window and the Touchpad does not finger down, at the top or bottom right of the Touchpad (depending on the respond.
  • Page 207 Troubleshooting Problem Possible Cause - Solution Wireless LAN/Bluetooth/3.75G/ The modules are off. Check the LED indicator and/or function key indicator HSPA modules cannot be detected. to see if the WLAN/Bluetooth/3.75G/HSPA module is on or off (see “LED Indicators” on page 1 - 12).
  • Page 208 Troubleshooting Problem Possible Cause - Solution I cannot obtain high speed Bluetooth data To obtain high speed Bluetooth data transfer take into account the following: transfer. • To achieve high speed transfer speeds, both devices must sup- port high speed data transfer (i.e both the computer and the Bluetooth compatible device you are connecting to).

  • Page 209: Bluetooth Connection Problems

    Troubleshooting Bluetooth Connection Problems If you are experiencing problems connecting to some Bluetooth devices (in particular certain mobile phones and headsets) it maybe necessary to download and install the Windows Mobile Device Center software (for Win- dows Vista and Windows 7). Go to the Microsoft website and search for the Microsoft Windows Device Center Driver for Windows Vista (64-bit or 32-bit) and Windows 7 (64-bit or 32-bit), and then download the driver.
  • Page 210 Troubleshooting Right-click Bluetooth Peripheral Device and click on Update Driver Software. Click Browse my computer for driver software. Click Let Me pick from a list of device drivers on my computer. Figure 8 - 2 - Browse my computer.../Let me pick from... Select Bluetooth Radios from the list.
  • Page 211 Troubleshooting 10. A list of drivers will appear with Manufacturer on one side and Model in the other. 11. Choose Microsoft Corporation (make sure you choose the full name Microsoft Corporation and do not choose Microsoft - Note that you must have installed the Microsoft Windows Device Center Driver for Microsoft Corporation to appear in the list).
  • Page 212 Troubleshooting 15. The Device Manager should now display the Windows Mobile-based device support under Bluetooth Radios. 16. You will need to repeat the process for any other Bluetooth Peripheral Devices listed under Other Devices. Figure 8 - 5 - Device Manager - Bluetooth Radio 8 - 16 Bluetooth Connection Problems...

  • Page 213: Interface (Ports & Jacks)

    Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc. Interface (Ports & Jacks) A - 1...

  • Page 214: Notebook Ports And Jacks

    Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer.
  • Page 215 Interface (Ports & Jacks) Item Description Microphone-In Jack Plug an external microphone in to this jack to record on your computer. RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot.
  • Page 216 Interface (Ports & Jacks) A - 4...

  • Page 217: Amd Video Driver Controls

    AMD Video Driver Controls Appendix B: AMD Video Driver Controls  The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - Video Card Options Note that card types, spec- Video Driver Installation ifications and drivers are subject to continual up- Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 -...

  • Page 218: B - 2 Amd Vision Engine/Catalyst™ Control Center

    AMD Video Driver Controls AMD Vision Engine/Catalyst Control Center ™  Adjust the video settings from the AMD/ATI Control Center. Taskbar Icon Right-click the desktop and select AMD VisionEngine/Catalyst Control Center. The Control Center can also be accessed by dou- Click Advanced settings in the Screen Resolution control panel (see “Video ble-clicking the icon...

  • Page 219: Amd Vision Engine/Catalyst™ Control Center Preferences

    AMD Video Driver Controls AMD Vision Engine/Catalyst™ Control Center Preferences  The Preferences button in the control center menu allows you to configure the con- trol panel settings. You can view the control panel in either Standard View or Ad- Preferences &...
  • Page 220 AMD Video Driver Controls Standard View The Standard View menus feature a series of menu headings with clickable sub- menus which allow you to adjust Desktops and Displays, Power, Video, Gaming and Information. Click the Start button to access the top level menu from any sub- menu heading.
  • Page 221 AMD Video Driver Controls Advanced View  The Advanced View menus display all the menu headings as a series of buttons on the left. Click the arrows in any button to display the sub-menus (note all the figures Sub-Menus in the remainder of this chapter are in Advanced View). Click a menu button to expand any sub-menus, and then click the appro-...
  • Page 222 AMD Video Driver Controls The control center provides additional video configuration controls and tools which  allow quick access to features such as display options, 3D Settings, color, power and Information menus etc. Adjust settings from the options in the sub-menus. Help Menus Press F1 to bring up Help menu.

  • Page 223: Display Devices & Options

    AMD Video Driver Controls Display Devices & Options  Besides the built-in LCD you can also use an external monitor/flat panel display/TV Function Key connected to the external monitor port or to the HDMI-Out port (High-Definition Combination Multimedia Interface) as your display device. The table below outlines the display You can use the Fn + F7 options.

  • Page 224: Configuring An External Display

    AMD Video Driver Controls Configuring an External Display  You can use the control center to configure any attached displays. Detect Displays Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Open the control center. Click Detect Displays (button) to automati- Select Desktop Management from the menu on the left (click the arrow to expand...
  • Page 225 AMD Video Driver Controls Click the triangle icon (or right-click the display icon) on the attached display  icon at the bottom to bring up the options (e.g Duplicate or Extend). Select an option from the menu (click Continue if required), and click Yes to Disable Displays accept the settings.
  • Page 226 AMD Video Driver Controls Desktop Properties Use Desktop Properites (Desktop Management) to configure the desktop area res- olution, color quality, refresh rate and rotation. If the displays are configured in Ex- tend mode then they may be configured independently. Figure B - 8 Desktop Management - Desktop...
  • Page 227 AMD Video Driver Controls My VGA Displays/My Digital Flat-Panels An additional menu button entitled My VGA Displays/My Digital Flat-Panels will appear (depending on the type of display attached) when an external display is at- tached. This menu allows you to configure the properties of the external display. Af- ter making any adjustments you may need to click the Apply button to confirm the changes.
  • Page 228 AMD Video Driver Controls HDTV Support If your flat panel supports HDTV functions then this can be configured from My Digital Flat-Panels > HDTV Support (Digital Flat-Panel). Figure B - 10 My Digital Flat- Panels (HDTV Support) B - 12 Display Devices & Options...

  • Page 229: Configuring An External Display In Windows 7

    AMD Video Driver Controls Configuring an External Display In Windows 7  Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go to the Screen resolution control panel (see “Video Features” on page 1 - 26).
  • Page 230 AMD Video Driver Controls You can configure the displays from the Multiple Displays menu. Figure B - 12 Screen Resolution Multiple Display Options (Win 7) • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) •...
  • Page 231 AMD Video Driver Controls Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configura- tion and modes (this is particularly useful when attaching a projector) in Windows 7. Attach your external display to the external monitor port and turn it on.
  • Page 232 AMD Video Driver Controls PowerPlay™ When enabled, PowerPlay can be used to automatically set to adjust the graphics ™ processor settings for higher performance or longer battery life when the system is either Plugged In or on Battery. Figure B - 14 PowerPlay ™...

  • Page 233: Hdmi Audio Configuration

    AMD Video Driver Controls HDMI Audio Configuration HDMI (High-Definition Multimedia Interface) carries both audio and video signals. Configure the audio output as per the instructions below. Connect a device with HDMI support to the HDMI-Out port. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound), and click Playback (tab).
  • Page 234 AMD Video Driver Controls Double-click the connected HDMI device (or right-click and select Properties) to adjust the HDMI settings from the control panel tabs. Click OK to close the control panel (see notes overleaf). Figure B - 16 HDMI Device Properties B - 18 HDMI Audio Configuration...
  • Page 235 AMD Video Driver Controls HDMI Notes  • Connect a device with HDMI support to the HDMI-Out port BEFORE attempt- ing to play audio/video sources through the device. Other Applications • To play audio sources through your external display’s (TV or LCD) speakers If you are using a third you will need to go to the audio configuration control panel on the display and party...
  • Page 236 AMD Video Driver Controls B - 20...

  • Page 237: Specifications

    Specifications Appendix C: Specifications  Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.

  • Page 238: Processor

    Specifications Processor Memory Display Models A, B & C: Models A & B: Model A: AMD-C Series Accelerated Processing Single Channel DDRIII (DDR3) 14.0” / 35.56cm HD (1366 * 768), 16:9 Unit - C30 1C (1.2GHz) Panel One 204 Pin SO-DIMM socket supporting 512KB L2 Cache, 40nm (40 Nanometer), Model B: DDR3 1066MHz/1333MHz (real...

  • Page 239: Bios

    Specifications Video Audio Slots Model C: High Definition Audio Interface Models A & B: Integrated with C50 APU - AMD Direct Sound 3D™ Compatible Two Mini-Card Slots with PCIe & USB Mobility Radeon™ HD 6250M PCIe * 16 Built-In Microphone Interfaces: Video Card 2 * Built-In Speakers...

  • Page 240: Communication

    Specifications Communication Power Indicators Built-In 10/100Mb Base-TX Ethernet LAN Models A & B: LED Indicators - Power/Suspend, Battery, HDD/ODD, Bluetooth/Wireless Removable 3 Cell Smart Lithium Ion Battery 1.3M/300K Pixel PC Camera Module LAN, Num Lock, Caps Lock, Scroll Lock Pack 24.42WH with USB interface (Factory Option) For Some Model A Designs: Removable 6 Cell Smart Lithium Ion Battery...

  • Page 241: Dimensions & Weight

    Specifications Dimensions & Weight Model A: 340mm (w) * 238mm (d) * 13.9 - 31.8mm (h) 2.05 kg with 3 Cell Battery & ODD For Model A Design II (and Some Other Model A Designs): 341mm (w) * 238.5mm (d) * 16- 34mm (h) 2.05 kg with 3 Cell Battery &...
  • Page 242 Specifications C - 6...

Table of Contents