Do you have a question about the GDSB02BT45 and is the answer not in the manual?
Questions and answers
Stephen
March 23, 2025
I have connected the RCA cables. White to white and red to red.
Still get no sound from T.V
My turntable plays fine via Bluetooth.
1 comments:
Mr. Anderson
March 23, 2025
There may be no sound from the Goodmans GDSB02BT45 when RCA cables are connected due to the following reasons: 1. The audio source volume is too low. Ensure the source device (e.g., phone or laptop) is set to about 70-80% volume. 2. The RCA cables are not properly connected. Verify that the 3.5mm jack is inserted into the headphone output of the external device and the red and white RCA jacks are correctly plugged into the RCA AUX input on the soundbar. 3. The soundbar is not set to AUX mode. Ensure the device is switched to AUX mode for RCA input to work. 4. The volume on the soundbar is too low. Increase the volume using the remote or soundbar buttons.
This answer is automatically generated
Mr Murray Nish
March 18, 2025
GDSB02BT45 - I havent set this up in my new home for the two years I have lived here. replace the batteries and the remote does not work... HELP
1 comments:
Mr. Anderson
March 18, 2025
If the remote for your Goodmans GDSB02BT45 does not work after replacing the batteries, ensure the battery is inserted correctly with the '+' side facing up. Also, check for any battery leakage that may have damaged the remote. If the issue persists, verify that the remote is within the 5-10 meter wireless range and has a clear line of sight to the soundbar. If the problem continues, consider replacing the remote.
Welcome Your Soundbar 2.1 In The Box 2.4 Rear view 2.2 Front View 2.5 Remote Control 2.3 Side View Quick Setup 3.4 Adjusting the Volume 3.1 Power On/Off and mode Selection 3.2 Standby & Auto Standby 3.5 Adjusting the EQ sound effects 3.6 Muting the sound 3.3 Fitting the remote control battery Operation...
Welcome Thank you for choosing this Goodmans product. We’ve been making electronics for the British people for 70 years. Each of our projects has been carefully designed to be great at what it does and this one is no exception. We hope you enjoy your new Soundbar.
Rear View RCA AUX input. Connect an RCA cable (supplied) to use the AUX in mode. DC POWER input socket. Connect TAKE CARE WITH the 18V mains plug to this socket to LIVE ELEMENTS power the Soundbar. GDSB02BT45...
News button. Press to Play or Pause playback of a paired Bluetooth device. button. Press to skip to the next track of a paired Bluetooth device. VOLUME+ button. Press to increase the volume output. TAKE CARE WITH LIVE ELEMENTS GDSB02BT45...
3. When in Bluetooth, Aux or Line in mode, once audio PAIR MODE playback has ceased and the unit has stood idle for approximately 20 minutes, it will switch into a ‘power-down’ power saving mode. FLAT 4. To wake the unit up, press the STANDBY button (C or K). GDSB02BT45...
EQ mode is inactive. Muting the sound 1. Press the MUTE button on the remote control (Q) during playback to mute the output. MODE PAIR 2. Press the MUTE button again to resume the audio output. FLAT GDSB02BT45...
If you turn off either device before pairing is complete the process will need to be repeated when powered on again. If you do not see ‘GDSB02BT45’ press the PAIR button (G or L) to re-initiate pairing mode. 5. Once paired the blue LED will stop flashing.
The volume output is effected by the volume level on the audio source EG: Phone or laptop, so make sure that is set to about 70-80% (not too loud to avoid distortion). 4. Adjust the VOLUME on the unit to the required listening level. GDSB02BT45...
The volume output is effected by the volume level on the audio source EG: Phone or laptop, so make sure that is set to about 70-80% (not too loud to avoid distortion). Adjust the VOLUME on the unit to the required listening level. PAIR MODE FLAT GDSB02BT45...
The external audio source volume is too high, decrease the volume level. Remote control does not work Reduce the distance between the remote and main unit Check the battery is installed correctly. Replace the battery Aim the remote directly at the Sound bar GDSB02BT45...
Speaker Impedance 4 Ohms Frequency Response 90~20000Hz S/N Ratio 80dB Max Power Consumption Dimensions 760mm (L) x 55mm (W) x 110mm (H) Customer Support Our customer service team is available for technical or guarantee support. Visit www.goodmans.co.uk/support QSG-JULY14-GDSB02BT45 www.goodmans.co.uk GDSB02BT45...
Need help?
Do you have a question about the GDSB02BT45 and is the answer not in the manual?
Questions and answers
I have connected the RCA cables. White to white and red to red. Still get no sound from T.V My turntable plays fine via Bluetooth.
There may be no sound from the Goodmans GDSB02BT45 when RCA cables are connected due to the following reasons:
1. The audio source volume is too low. Ensure the source device (e.g., phone or laptop) is set to about 70-80% volume.
2. The RCA cables are not properly connected. Verify that the 3.5mm jack is inserted into the headphone output of the external device and the red and white RCA jacks are correctly plugged into the RCA AUX input on the soundbar.
3. The soundbar is not set to AUX mode. Ensure the device is switched to AUX mode for RCA input to work.
4. The volume on the soundbar is too low. Increase the volume using the remote or soundbar buttons.
This answer is automatically generated
GDSB02BT45 - I havent set this up in my new home for the two years I have lived here. replace the batteries and the remote does not work... HELP
If the remote for your Goodmans GDSB02BT45 does not work after replacing the batteries, ensure the battery is inserted correctly with the '+' side facing up. Also, check for any battery leakage that may have damaged the remote. If the issue persists, verify that the remote is within the 5-10 meter wireless range and has a clear line of sight to the soundbar. If the problem continues, consider replacing the remote.
This answer is automatically generated