Icom IC-V88 Instructions page 2

D Entering the Front Panel Programming mode
(Step 1)
Rotate [VOL] to turn OFF the transceiver.
q
While pushing [P0] and [UP] at the same time, turn
w
ON the transceiver.
• "SET MODE" is displayed.
Push [P0] to enter the Front Panel Programming
e
mode.
• A zone number and a channel number are displayed.
To Exit the Front Panel Programming mode and re-
turn to normal operation:
Turn OFF the transceiver, and then turn it ON
➥
again.
D Selecting a channel to program (Step 2)
Push [P3] to enter the Channel Selection mode.
q
• The channel number blinks.
Push [P1] to select a zone.
w
Push [UP] or [DOWN] to select a channel you want
e
to program.
Push [P3] again to set the channel.
r
• The cursor stops blinking.
D Programming outline
Entering the Front Panel Programming mode (Step 1)
• Zone and Channel
[DOWN]
[P0]
[P2] [P3]
• Channel Selection
mode (Step 2)
• Deactivating or activating
channel (Step 6)
FRONT PANEL PROGRAMMING
D Editing the RX and TX frequencies (Step 3)
Push [UP] to first select the RX frequency, or push
q
again to select the TX frequency.
• The LED indicator lights green when you select the RX fre-
quency, and lights red when you select the TX frequency.
[P3] to enter the Frequency Edit mode.
w Push
• The cursor blinks at the first digit.
e Enter a desired frequency by pushing the keys on
the 10-key pad.
r After you finish entering all digits, the frequency will
automatically be saved.
• The cursor stops blinking.
D Selecting the RX and TX tones (Step 4)
Push [UP] to first select the RX tones or push again
q
to select the TX tones.
• The LED indicator lights green when you select the RX
tones, and lights red when you select the TX tones.
Push [P2] to select the CTCSS OFF, CTCSS tone
w
frequency, or DTCS code screen.
Push [P3] to enter the CTCSS Tone Frequency or
e
DTCS Code Selection mode.
• The frequency or the first digit code blinks.
Setting the CTCSS tone frequency:
Push [UP] or [DOWN] to select the frequency.
r
Push [P3] again to set the frequency.
t
• The frequency stops blinking.
Setting the DTCS code:
Push [UP] or [DOWN] to select the code.
r
Push [P3] to move the cursor to the next digit.
t
• RX frequency • TX frequency
[DOWN]
[UP]
[UP]
*2
[P1] [P2] [P3] [P2]
• Frequency Edit • Frequency Edit
mode (Step 3) mode (Step 3)
*1
[P2]
• Clearing the RX frequency
• Inhibiting or allowing
memory (Step 6)
transmission (Step 6)
• Toggling the channel passband width
Repeat steps r and t until you finish selecting the
y
code.
Push [P1] to toggle the DTCS code's polarity while
u
the cursor is blinking.
• You can select Normal or Inverse polarity.
Normal
Push [P3] again to save the code.
i
• The cursor stops blinking.
D Editing the channel name (Step 5)
You can display the name instead of the channel number.
[UP] to display the channel name.
q Push
• If no channel name is programmed, nothing is displayed.
w Push [P3] to enter the Channel Name Edit mode.
• The cursor blinks at the first digit.
Enter a character by pushing
e
the keys on the 10-key pad.
When using the 10-key pad:
Repeatedly pushing
➥
the number "2." Continuing to push it selects capital
letters "A," then "B," then "C," and then selects lower
case letters "a," then "b," then "c."
• To enter a space, push
then push [P3] to move to the next digit.
• [0] and [1] also select other symbols.
• [✱] and [#] are used to move the cursor to the left or to
the right.
[P3] to move the cursor to the next digit.
r Push
• RX CTCSS tone frequency OFF screen
[DOWN]
[UP]
*2
[P3] [P2]
• RX CTCSS tone frequency screen
*2
[P3]
[P2]
• CTCSS Tone Frequency
Selection mode (Step 4)
• RX DTCS code screen
*2
[P3]
• DTCS Code Selection mode
t Repeat steps e and r until you finish entering the
name.
Push
y
• The cursor stops blinking.
D Other settings (Step 6)
lnverse
To deactivate or activate the channel:
➥ Select a desired zone and the channel to deactivate
and then push [P2].
" • " is displayed.
• The channel cannot be used until you re-activate it.
To activate the channel, push
➥
To toggle between Wide and Narrow channel pass-
band width:
➥ Select a RX frequency, and then push
cannot toggle if the cursor is blinking.)
• "WIDE" or "NARROW" is briefly displayed.
To clear the RX frequency memory:
[UP] or [DOWN], or
Select a RX frequency, and then push
➥
cannot clear the RX frequency memory if the cursor
is blinking.)
[2], for example, first selects
• The channel will be cleared and you have to set the RX
frequency again to use the channel.
To Inhibit or allow transmission:
Select a TX frequency, and then push
➥
[1] twice. The cursor blinks, and
cannot inhibit transmission if the cursor is blinking.)
• "TX INH" is displayed.
To allow transmission, push
➥
*3
• TX CTCSS tone frequency OFF screen
[DOWN]
*3
[UP]
[P2]
• TX CTCSS tone frequency screen
*2
[P3]
[P2]
• CTCSS Tone Frequency
Selection mode (Step 4)
• TX DTCS code screen
[P2] [P2]
*2
[P3]
• DTCS Code Selection mode
(Step 4)
[P3] again to save the channel name.
[P2].
[P1]. (You
[P2]. (You
[P2]. (You
[P2].
*3
• Channel name
[DOWN]
[UP]
[UP]
[P3]
• Channel Name Edit
mode (Step 5)
NOTE:
*1: Once you clear the RX frequency
memory, you have to set the RX fre-
quency again to use the channel.
*2: Settable in the same way for both
RX and TX.
*3: The CTCSS OFF, a CTCSS tone
frequency or a DTCS code screen is
displayed.
(Step 4)