Kenwood VR-6070 Instruction Manual page 19

Preparing for surround sound
8 Use the MULTI CONTROL knob or Multi (%/fi) to select the
appropriate surround speaker setting.
If you selected "LARGE" as the center speaker setting,
1 SURR LARGE
2 SURR NORMAL : Average size surround speakers are
3 SURR OFF
If you selected other than "LARGE" as the center speaker setting,
1 SURR ON
: Surround speaker setting mode to the
receiver is ON.
2 SURR OFF : Surround speaker setting mode to the
receiver is OFF.
• When the setting "SURR OFF" is selected, the procedure skips
to step #.
9 Press the ∧ key or # keys again to accept the setting.
• The surround speaker setting indication "SB" appears.
0 Use the MULTI CONTROL knob or Multi (%/fi) keys to
select appropriate surround back speaker setting.
If you selected "LARGE" as the surround speaker setting,
1 SB NORMAL :
2 SB LARGE
:
3 SB OFF
:
SP MUTE OPTICAL 6CH INPUT
AUTO DETECT
A B CLIP
COAXIAL ANALOG
L C SW R
LFE
SL S SB SR
If you selected "NORMAL" as the surround speaker setting,
1 SB ON : Surround back speaker setting mode to the
receiver is ON.
2 SB OFF : Surround back speaker setting mode to the
receiver is OFF.
• After setting SB (surround back) from OFF to ON, 6ch AMP setup
display will appear to enable you to re-select either SW or SB from
the surround back or subwoofer speaker terminal.
! Press the ∧ key or # key again to accept the setting and
"SURR:MIX" appears.
• Surr:mix is when the SL and SR speakers signals are mixed to
produce sound from the surround back speaker which would
enable the listener to enjoy sound coming from the back.
SP MUTE OPTICAL 6CH INPUT
AUTO DETECT
A B CLIP
COAXIAL ANALOG
L C SW R
LFE
SL S SB SR
@ Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the following.
1 SURR:MIX ON : Surround mix setting mode to the
2 SURR:MIX OFF : Surround mix setting mode to the
• If surround back speaker is turned off, SURR:MIX setting is not
visible and the procedure skips to step #.
# Press the ∧ key or # key again to accept the setting.
• The subwoofer remix setting indication "SW RE-MIX" appears.
: Large surround speakers are
connected to the receiver.
connected to the receiver.
: Surround speaker setting mode to
the receiver is OFF.
Average size surround back speaker is
connected to the receiver.
Large surround back speaker is
connected to the receiver.
Surround back speaker setting mode to
the receiver is OFF.
CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6
ACTIVE EQ. MATRIX
Surround EX
96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII
CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6
ACTIVE EQ. MATRIX
Surround EX
96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII
receiver is ON.
receiver is OFF.
$ Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the appropriate subwoofer re-mix setting.
1 SW RE-MIX ON : Subwoofer re-mix setting mode to
2 SW RE-MIX OFF : Subwoofer re-mix setting mode to
• If subwoofer is turned off, subwoofer re-mix setting is not visible.
% Press the SETUP key again to return to the main setup
displays.
• The receiver enters the speaker volume level adjustment mode.
• In steps 4 and 5, indications appear only for the selected
channels of the speakers that require adjusting.
5
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
1 Press the ∧ / ∨ keys or @/#keys to select TEST TONE.
2 Press the SETUP key for the following displays:
1 T.TONE AUTO
2 T.TONE MANUAL
3 The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or Multi (%/fi) keys.
Press the SETUP key again to begin TEST TONE.
Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust
the volume level of the test tone output from the speaker
channel to be adjusted.
For AUTO selection, the first test tone is heard from the front left
speaker for 2.5 seconds. The next test tone is heard from the
speakers in the following sequence for 2 seconds each.
RDS
THX
RTY
AUTO
MEMO
STEREO
TUNED
The channel indication blinks while the test tone is being output.
L C SW R
LFE
SL S SB SR
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed.
• If the speaker setting selects are OFF, the speaker level settings
are reset.
For MANUAL selection, press the ∧ / ∨ keys or @/# keys each
time to select the speaker channel.
4 Press the SETUP key again.
• The test tone is turned off and return to the main setup displays.
RDS
THX
6
RTY
Input the distance to the speakers.
AUTO
MEMO
STEREO
1 Press the ∧ / ∨ keys or @/# keys to select the SP DISTANCE on
TUNED
setup displays and press the SETUP key again.
2 Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to Front left speaker (L)
Distance to Center speaker (C)
Distance to Front right speaker (R) : ____ feet (meters)
Distance to Surround right (SR)
Distance to Surround back (SB)
Distance to Surround left (SL)
Distance to Subwoofer (SW)
the receiver is ON.
the receiver is OFF.
LEFT CNTR
SUBW SL SB
SP MUTE OPTICAL 6CH INPUT CINEMA EQ. DTS.
AUTO DETECT
ACTIVE EQ. MATRIX
A B CLIP
COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE
Continued to next page.
RIGHT
SR
DOLBY DIGITAL STEREO NEO:6 RDS
THX
RTY
Surround EX
PRO LOGIC LOUDNESS CSII
AUTO
MEMO
STEREO
TUNED
º
: ____ feet (meters)
: ____ feet (meters)
: ____ feet (meters)
: ____ feet (meters)
: ____ feet (meters)
: ____ feet (meters)
19
EN