Summary of Contents for Dodge 2012 Ram Truck Gas 1500
Page 1
2 0 1 2 R a m T R u c k G a s 1 5 0 0 / 2 5 0 0 / 3 5 0 0 O W N E R ’ s m a N u a L...
Page 2
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of features Chrysler Group LLC shall be deemed to be deleted and the and equipment that are either standard or optional on this name Chrysler Canada Inc.
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
6 INTRODUCTION WARNINGS AND CAUTIONS also be supplied with your vehicle. If these instructions This Owner’s Manual contains WARNINGS against op- are missing, please contact your authorized dealer for erating procedures that could result in a collision or assistance in obtaining replacement documents from the bodily injury.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Vehicle Identification Number NOTE: It is illegal to remove or alter the VIN.
Page 11
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS ▫ General Information ....18 A Word About Your Keys ....12 ▫...
Page 12
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Lock The Doors ....23 ▫ Wind Buffeting ..... . . 37 ▫...
Page 13
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Seat Belt Extender ..... 54 Engine Break-In Recommendations ..82 ▫...
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Wireless Ignition Node (WIN) — If Equipped The Wireless Ignition Node (WIN) operates similar to an Key Fob with Remote Keyless Entry (RKE) — If ignition switch. It has four operating positions, three with Equipped detents and one that is spring-loaded.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the emergency key, slide the mechanical latch Removing Key Fob From Ignition at the top of the Key Fob sideways with your thumb and Place the shift lever in PARK (if equipped with an then pull the key out with your other hand.
Page 17
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 (EVIC)/Personal Settings (Customer-Programmable WARNING! Features)” in “Understanding Your Instrument Panel” • Before exiting a vehicle, always apply the parking for further information. brake, shift the transmission into PARK, and re- CAUTION! move the key fob from the ignition. When leaving the vehicle, always lock your vehicle.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If equipped with Electronic Vehicle Information Cen- WARNING! (Continued) ter (EVIC) the EVIC will display “Key In Ignition”. • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may SENTRY KEY cause serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 NOTE: A Key Fob that has not been programmed is also CAUTION! considered an invalid key. The Sentry Key Immobilizer system is not compat- During normal operation, after turning on the ignition ible with some after-market remote starting systems.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If a programmed Key Fob is lost, see your authorized CAUTION! dealer to have all remaining Key Fobs erased from the system’s memory. This will prevent the lost Key Fobs Always remove the Sentry Keys from the vehicle from starting your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 VEHICLE SECURITY ALARM — IF EQUIPPED To Arm The System The Vehicle Security Alarm monitors the vehicle doors The Vehicle Security Alarm will set when you use the and ignition for unauthorized operation. When the Ve- power door locks, or use the Remote Keyless Entry (RKE) hicle Security Alarm is activated, interior switches for transmitter to lock the doors.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Vehicle Security Alarm will also disarm if a pro- ILLUMINATED ENTRY — IF EQUIPPED grammed Sentry Key is inserted into the ignition The courtesy lights will turn on when you use the switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 • The illuminated entry system will not operate if the dimmer control is in the “dome defeat” position (extreme bottom position). REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED The RKE system allows you to lock or unlock the doors and activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a Key Fob with RKE transmitter.
Page 24
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seconds to unlock all doors. The turn signal lights will than ten seconds. Then, press and hold the UNLOCK flash to acknowledge the unlock signal. The illuminated button while still holding the LOCK button. entry system will also turn on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Flash Lamps With Remote Key Lock 3. Test the feature while outside of the vehicle by press- This feature will cause the turn signal lights to flash when ing the LOCK/UNLOCK buttons on the RKE transmitter the doors are locked or unlocked with the RKE transmit- with the ignition switch in the OFF position and the key ter.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sound Horn With Remote Key Lock 3. Test the feature while outside of the vehicle by press- This feature will cause the horn to chirp when the doors ing the LOCK button on the RKE transmitter with the are locked with the RKE transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 The Panic Alarm will stay on for three minutes unless Transmitter Battery Replacement you turn it off by either pressing the PANIC button a The recommended replacement battery is one CR2032 second time or drive the vehicle at a speed of 5 mph battery.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To assemble the RKE transmitter case, snap the two If your RKE transmitter fails to operate from a normal halves together. distance, check for these two conditions: General Information 1. A weak battery in the RKE transmitter. The expected This device complies with Part 15 of the FCC rules and life of the battery is a minimum of three years.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 How To Use Remote Start WARNING! All of the following conditions must be met before the • Do not start or run an engine in a closed garage or engine will remote start: confined area.
Page 30
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Remote Start Aborted — Hood Ajar • If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds. • Remote Start Aborted — Fuel Low •...
Page 31
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 NOTE: To avoid unintentional shut downs, the system message “Turn To On” will flash in the EVIC until you will disable the one time press of the REMOTE START turn the ignition switch to the ON/RUN position. button for two seconds after receiving a valid Remote •...
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Information Center (EVIC)/Customer-Programmable WARNING! Features (System Setup)” in “Understanding Your Instru- • Do not leave children or animals inside parked ment Panel”. vehicles in hot weather. Interior heat build-up may DOOR LOCKS cause serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Power Door Locks — If Equipped WARNING! (Continued) A power door LOCK switch is on each front door trim • Allowing children to be in a vehicle unattended is panel. Use this switch to lock or unlock the doors. dangerous for a number of reasons.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you press the power door LOCK switch while the Key Auto Unlock Doors — If Equipped Fob is in the ignition, and any front door is open, the This feature unlocks all of the doors of the vehicle when power locks will not operate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Child-Protection Door Lock To use the system, open each rear door, use a flat blade To provide a safer environment for children riding in the screwdriver (or emergency key) and rotate the dial to rear seat, the rear doors (if equipped) of your vehicle engage and disengage the Child-Protection locks.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS WARNING! Power Windows — If Equipped Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged.
Page 37
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 The control on the left front door panel has UP-DOWN WARNING! switches that give you fingertip control of all power windows. There is a single opening and closing switch on Never leave children alone in a vehicle. Leaving the front passenger door for passenger window control unattended children in a vehicle is dangerous for a and on the rear doors of Quad Cab , Mega Cab and...
Page 38
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the window part way, press to the first detent conditions may trigger the auto reverse function unex- and release it when you want the window to stop. pectedly during auto closure. If this happens, pull the switch lightly to the first detent and hold to close the Auto-Up Feature With Anti-Pinch Protection window manually.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 2. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. Window LOCKOUT Switch —...
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Supplemental Seat-Mounted Side Air Bags (SAB) — if normal occurrence and can be minimized. If the rear windows are open and buffeting occurs, open the front equipped and rear windows together to minimize the buffeting. •...
Page 41
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 If you will be carrying children too small for adult-sized WARNING! seat belts, the seat belts or the Lower Anchors and Tether for CHildren (LATCH) feature also can be used to hold Infants in rear facing child restraints should never infant and child restraint systems.
Page 42
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If a child from 1 to 12 years old (not in a rear facing child 5. If the air bag system in this vehicle needs to be seat) must ride in the front passenger seat, move the seat modified to accommodate a disabled person, contact as far back as possible and use the proper child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Buckle up even though you are an excellent driver, even WARNING! (Continued) on short trips. Someone on the road may be a poor driver • Being too close to the steering wheel or instrument and cause a collision that includes you.
Page 44
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE collision the belt will lock and reduce the risk of you WARNING! (Continued) striking the inside of the vehicle or being thrown out. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat WARNING! belts.
Page 45
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 2. The seat belt latch plate is above the back of the front 3. When the belt is long enough to fit, insert the latch seat, next to your arm in the rear seat. Grasp the latch plate into the buckle until you hear a “click.”...
Page 46
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • A belt that is worn under your arm is dangerous. • A belt buckled into the wrong buckle will not Your body could strike the inside surfaces of the protect you properly.
Page 47
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap belt portion, pull up • A lap belt worn too high can increase the risk of on the shoulder belt.
Page 48
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE belt tongue is pressed into the buckle. Allow the retractor WARNING! to take up the extra webbing, and the buckles will hang vertically from the cab back exit bezel, thus freeing up all A frayed or torn belt could rip apart in a collision and the area behind the front seats.
Page 49
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 panel and insert it into the black keyed buckle until there is an audible “click”. For proper seat belt usage, refer “Lap/Shoulder Belt Operating Instructions”. WARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury...
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold that begins immediately above the latch plate. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Center Lap Belts The center seating position for the Quad Cab , Mega Cab and Crew Cab front seat has a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a click.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • N/A — Not Applicable Seat Belts In Passenger Seating Positions The seat belts in the passenger seating positions are • ALR — Automatic Locking Retractor equipped with Automatic Locking Retractors (ALR) which are used to secure a child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 When To Use The Automatic Locking Mode WARNING! Use the Automatic Locking Mode anytime a child safety • The belt and retractor assembly must be replaced seat is installed in a seating position that has a belt with this feature.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These devices are not a substitute for proper seat WARNING! belt placement by the occupant. The seat belt still must be • The belt and retractor assembly must be replaced worn snugly and positioned properly. if the seat belt assembly “Automatic Locking Re- The pretensioners are triggered by the Occupant Re- tractor (ALR)”...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 The BeltAlert warning sequence begins after the vehicle BeltAlert can be enabled or disabled by your authorized speed is over 5 mph (8 km/h), by blinking the Seat Belt dealer. Chrysler Group LLC does not recommend deac- Reminder Light and sounding an intermittent chime.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Extender Supplemental Restraint System (SRS) — Air Bags If a seat belt is too short even when fully extended, and This vehicle has Advanced Front Air Bags for both the the adjustable upper shoulder belt anchorage (if so driver and front passenger as a supplement to the seat equipped) is in its lowest position, your authorized...
Page 57
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 The Advanced Front Air Bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the Advanced Front Air Bags based upon...
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle may also be equipped with Supplemental Air Bag System Components Side Air Bag Inflatable Curtains (SABIC) to protect the Your vehicle may be equipped with the following air bag driver, front, and rear passengers sitting next to a win- system components: dow.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 • Front and Side Impact Sensors WARNING! • Seat Belt Buckle Switch • No objects should be placed over or near the air bag on the instrument panel, because any such Advanced Front Air Bag Features objects could cause harm if the vehicle is in a The Advanced Front Air Bag system has multistage collision severe enough to cause the air bag to...
Page 60
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Seat-Mounted Side Air Bags (SAB) When the air bag deploys, it opens the seam between the — If Equipped front and side of the seat’s trim cover. Each air bag Supplemental Seat-Mounted Side Air Bags (SAB) may deploys independently;...
Page 61
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 The system includes side impact sensors that are cali- brated to deploy the side air bags during impacts that require air bag occupant protection. WARNING! • If your vehicle is equipped with left and right Supplemental Side Air Bag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Deployment Sensors And Controls WARNING! (Continued) Occupant Restraint Controller (ORC) • If your vehicle is equipped with SABIC air bags, The ORC is part of a Federally regulated safety system do not have any accessory items installed which required for this vehicle.
Page 63
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 The Advanced Front Air Bags will not deploy in all The ORC monitors the readiness of the electronic parts of frontal collisions, including some that may produce sub- the air bag system whenever the ignition switch is in the stantial vehicle damage —...
Page 64
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE It also includes diagnostics that will illuminate the instru- When the ORC detects a collision requiring the Ad- ment cluster Air Bag Warning Light if a malfunction is vanced Front Air Bags, it signals the inflator units. A large noted that could affect the air bag system.
Page 65
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Supplemental Seat-Mounted Side Air Bag (SAB) Supplemental Side Air Bag Inflatable Curtain Inflator Units — If Equipped (SABIC) Inflator Units — If Equipped The Supplemental Seat-Mounted Side Air Bags are de- During collisions where the impact is confined to a signed to activate only in certain side collisions.
Page 66
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Turn on the interior lights, which remain on as long as Because air bag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of the battery has power or until the ignition key is whether or not an air bag should have deployed.
Page 67
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 • The nylon air bag material may sometimes cause continues, see your doctor. If these particles settle on abrasions and/or skin reddening to the driver and your clothing, follow the garment manufacturer’s in- front passenger as the air bags deploy and unfold.
Page 68
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Air Bag System WARNING! (Continued) • Do not attempt to modify any part of your air bag WARNING! system. The air bag may inflate accidentally or • Modifications to any part of the air bag system may not function properly if modifications are could cause it to fail when you need it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Air Bag Warning Light NOTE: If the speedometer, tachometer, or any engine You will want to have the air bags ready to related gauges are not working, the Occupant Restraint inflate for your protection in a collision. The Controller (ORC) may also be disabled.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Whether or not the driver and passenger safety belts To read data recorded by an EDR, special equipment is were buckled/fastened; required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, •...
Page 71
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Infants And Child Restraints WARNING! Safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until In a collision, an unrestrained child, even a tiny baby, they reach either the height or weight limit of their rear can become a projectile inside the vehicle.
Page 72
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE held in the vehicle by the lap/shoulder belt or the as long as possible, up to the highest weight or height LATCH child restraint anchor system. Refer to “Lower allowed by the child seat. These child seats are also held Anchors and Tether for CHildren (LATCH)”.
Page 73
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 • Make sure that the child is upright in the seat. WARNING! • The lap portion should be low on the hips and as snug • Improper installation can lead to failure of an as possible.
Page 74
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The restraint must be appropriate for your child’s around, and insert the latch plate into the buckle weight and height. Check the label on the restraint for again. If you still can’t make the child restraint secure, weight and height limits.
Page 75
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Lower Anchors and Tether for CHildren (LATCH) Each vehicle is equipped with the child restraint anchor- age system called LATCH, which stands for Lower Anchors and Tether for CHildren. The LATCH system provides for the installation of the child restraint without using the vehicle seat belt, instead securing the child restraint using lower anchorages and upper tether straps...
Page 76
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraint systems having attachments designed to NOTE: • When using the LATCH attaching system to install a connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection child restraint, please ensure that all seat belts not to the seat back tether anchorage have been available for being used for occupant restraints are stowed and out...
Page 77
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Installing The Child Restraint System We urge you to carefully follow the directions of the manufacturer when installing your child restraint. Many, WARNING! but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or Do not install child restraint systems equipped with connector, and a means for adjusting the tension in the...
Page 78
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The chart below defines the seating positions with an WARNING! Automatic Locking Retractor (ALR) or a cinching latch Improper installation of a child restraint to the plate. LATCH anchorages can lead to failure of an infant or Driver Center Passenger...
Page 79
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Installing a Child Restraint with an ALR: retractor to route it through the belt path of the child restraint. Slide the latch plate into the buckle until you 1. To install a child restraint with ALR, first, pull enough hear a “click.”...
Page 80
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Regular Cab models have two tether anchorages, one Tether Anchorage Points At The Right And Center each behind the front center and right seats. Quad Cab , Front Seat (Regular Cab - All Seats) Mega Cab and Crew Cab models have three anchor- 1.
Page 81
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Multiple Child Restraint Installation Sequence (Quad Cab /Crew Cab/Mega Cab - Rear Seats) Mega Cab 1. Place a child restraint on each outboard rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat.
Page 82
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Lift the cover, and attach the hook to the square Quad Cab /Crew Cab opening in the sheet metal. 1. The tether straps loops are located between the rear glass and the rear seat. There is a tether strap loop located behind each seating position.
Page 83
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 2. Place a child restraint on each outboard rear seat and adjust the tether strap so that it will reach under the head restraint, through the outboard tether strap loop, then route it to the tether strap loop located directly behind the center rear seat.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets The engine oil installed in the engine at the factory is a Air Bags deploying in the front seat could harm your pet. high-quality energy conserving type lubricant. Oil An unrestrained pet will be thrown about and possibly changes should be consistent with anticipated climate injured, or injure a passenger during panic braking or in conditions under which vehicle operations will occur.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Exhaust Gas WARNING! • Do not leave children or animals inside parked WARNING! vehicles in hot weather. Interior heat build-up may Exhaust gases can injure or kill. They contain carbon cause serious injury or death. monoxide (CO), which is colorless and odorless.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The WARNING! (Continued) Vehicle • If it is necessary to sit in a parked vehicle with the Seat Belts engine running, adjust your heating or cooling Inspect the belt system periodically, checking for cuts, controls to force outside air into the vehicle.
Page 87
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Defroster WARNING! (Continued) Check operation by selecting the defrost mode and place • Always make sure that floor mats are properly the blower control on high speed. You should be able to attached to the floor mat fasteners.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE lodged in the tread or sidewall. Inspect the tread for cuts WARNING! (Continued) and cracks. Inspect sidewalls for cuts, cracks and bulges. • Always make sure that objects cannot fall into the Check the wheel nuts for tightness.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ Illuminated Vanity Mirror — If Equipped ..98 Mirrors ......94 ▫...
Page 90
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Things You Should Know About Your ▫ Manual Reclining Seats — If Equipped ..144 Uconnect™ Phone ....119 ▫...
Page 91
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 ▫ Automatic Headlights — If Equipped ..159 Windshield Wipers And Washers ..165 ▫ Headlights On With Wipers ▫...
Page 92
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Resume Speed ....173 Parkview Rear Back Up Camera — If Equipped ......184 ▫...
Page 93
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 ▫ Using HomeLink ▫ Wind Buffeting ..... . 199 ....194 ▫...
Page 94
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage ......209 Rear Window Features ....218 ▫...
Page 95
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 ▫ Removing The Tailgate ....237 Easy-Off Tailgate ..... . 236 ▫...
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. The mirror should be adjusted while set in the day position (toward the windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 to the left of the button will illuminate to indicate when CAUTION! the dimming feature is activated. The sensor to the right of the button does not illuminate. To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in a passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Power Mirrors — If Equipped The controls for the power mirrors are located on the driver’s door trim panel. Power Mirror Controls 1 — Mirror Select Buttons 2 — Four-Way Mirror Control Switch Power Mirror Controls To adjust a mirror, press either the L (left) or R (right) The power mirror controls consist of mirror select but-...
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using the mirror control switch, press on any of the four Heated Mirrors — If Equipped arrows for the direction that you want the mirror to These mirrors are heated to melt frost or ice. This move.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 To use the “Slide-On-Rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “Slide-On-Rod” until the sun visor is in the desired position. Illuminated Vanity Mirror “Slide-On-Rod” Features Of Sun Visor — If Equipped The sun visor “Slide-On-Rod”...
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Trailer Towing Mirrors — If Equipped NOTE: Fold the trailer towing mirrors rearward prior to These mirrors are designed with an adjustable mirror entering an automated car wash. head to provide a greater vision range when towing A small blindspot mirror is located next to main mirror extra-wide loads.
For Uconnect™ customer support, visit the following long as your phone is turned on and has been paired to websites: the vehicle’s Uconnect™ Phone. The Uconnect™ Phone • www.chrysler.com/uconnect allows up to seven mobile phones to be linked to the • www.dodge.com/uconnect...
Page 104
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE system. Only one linked (or paired) mobile phone can be Voice Command Button used with the system at a time. The system is available in Actual button location may vary with the ra- English, Spanish, or French languages.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Operation example, you can use the compound form voice Voice commands can be used to operate the Uconnect™ command “Phonebook New Entry”, or you can break Phone and to navigate through the Uconnect™ Phone the compound form command into two voice com- menu structure.
Page 106
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, after the beep, say “Pair a Device” Cancel Command At any prompt, after the beep, you can say “Cancel” and and follow the audible prompts. you will be returned to the main menu. However, in a •...
Page 107
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 phone to use if multiple mobile phones are in the Call By Saying A Name vehicle at the same time. For example, if priority three • Press the button to begin. and priority five phones are present in the vehicle, the •...
Page 108
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Add Names To Your Uconnect™ Phonebook After you are finished adding an entry into the phone- book, you will be given the opportunity to add more NOTE: Adding names to the Uconnect™ Phonebook is phone numbers to the current entry or to return to the recommended when the vehicle is not in motion.
Page 109
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • To call a name from the Uconnect™ Phonebook or • Only the mobile phone’s phonebook is downloaded. downloaded Phonebook, follow the procedure in SIM card phonebook is not part of the Mobile phone- “Call by Saying a Name”...
Page 110
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say mobile and a home number, but you can add “John “Phonebook Edit Entry”. Doe’s” work number later using the “Phonebook Edit Entry” feature. •...
Page 111
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 • The Uconnect™ Phone will ask you to verify that you from the list, press the button while the Uconnect™ Phone is playing the desired entry and say wish to delete all the entries from the phonebook. “Delete”.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To call one of the names in the list, press the Answer Or Reject An Incoming Call — No Call button during the playing of the desired name, and Currently In Progress say “Call”.
Page 113
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 when another call is in progress. Therefore, the user can Toggling Between Calls only answer an incoming call or ignore it. If two calls are in progress (one active and one on hold), press the button until you hear a single beep, Making A Second Call While Current Call Is In...
Page 114
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE press and hold the button until you hear a double NOTE: This may not be the last number dialed from the beep, indicating that the two calls have been joined into Uconnect™ Phone. one conference call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 • An active call is automatically transferred to the NOTE: After every Uconnect™ Phone language change mobile phone after the ignition key is switched to OFF. operation, only the language-specific 32-name phone- book is usable. The paired phone name is not language- Uconnect™...
Page 116
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say WARNING! “Emergency” and the Uconnect™ Phone will instruct the paired mobile phone to call the emergency num- To use your Uconnect™ Phone System in an emer- ber.
Page 117
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Mexico City in Mexico). Please refer to the 24-Hour Working With Automated Systems “Towing Assistance” coverage details on the DVD in This method is used in instances where one generally has the Warranty Information Booklet and the 24-Hour to press numbers on the mobile phone keypad while Towing Assistance references.
Page 118
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE is also to be used for navigating through an automated Barge In — Overriding Prompts customer service center menu structure, and to leave a The “Voice Command” button can be used when you number on a pager.
Page 119
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Phone And Network Status Indicators NOTE: Certain brands of mobile phones do not send the If available on the radio and/or on a premium display dial ring to the Uconnect™ Phone to play it on the vehicle such as the instrument panel cluster, and supported by audio system, so you will not hear it.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Advanced Phone Connectivity List Paired Mobile Phone Names • Press the Transfer Call To And From Mobile Phone button to begin. The Uconnect™ Phone allows ongoing calls to be trans- • After the “Ready” prompt and the following beep, say ferred from your mobile phone to the Uconnect™...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 • After the “Ready” prompt and the following beep, say • You can also press the button at any time while the “Setup Select Phone” and follow the prompts. list is being played, and then choose the phone you wish to delete.
Page 122
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press the button and say the “Voice Training, This will delete all phone pairing, phone book entries, System Training, or Start Voice Training” command. and other settings in all language modes. The System will prompt you before resetting to factory settings.
Page 123
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 • low-to-medium vehicle speed, • Phonebook (Downloaded and Uconnect™ Phone Lo- cal) name recognition rate is optimized when the • low road noise, entries are not similar. • smooth road surface, • Numbers must be spoken in single digits. “800” must •...
Page 124
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • low road noise, Recent Calls If your phone supports “Automatic Phonebook Down- • smooth road surface, load”, Uconnect™ Phone can list your Outgoing, Incom- • fully closed windows, ing and Missed Calls. •...
Page 125
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 After reading a message, you can “Reply” or “Forward” List of Preset Messages: the message using Uconnect™ Phone. 1. Yes Send Messages: 2. No You can send messages using Uconnect™ Phone. To send a new message: 3.
Page 126
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say 13. I’ll be late “Setup, SMS Incoming Message Announcement,” you 14. Are you there yet? will then be given a choice to change it. 15.
Page 127
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125...
Page 128
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 129
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127...
Page 130
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 131
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information NOTE: Take care to speak into the Voice Interface This device complies with Part 15 of the FCC rules and System as calmly and normally as possible. The ability of RSS 210 of Industry Canada. Operation is subject to the the Voice Interface System to recognize user voice com- following conditions: mands may be negatively affected by rapid speaking or a...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 If you ever wish to interrupt the system while it lists The system will best recognize your speech if the win- options, press the Voice Command button, listen dows are closed, and the heater/air conditioning fan is for the beep, and say your command.
Page 134
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Use the ON/OFF VOLUME rotary knob to adjust the Radio AM volume to a comfortable level while the Voice Command To switch to the AM band, say “AM” or “Radio AM”. In system is speaking.
Page 135
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 • “Menu Radio” (to switch to the radio menu) Disc To switch to the disc mode, say “Disc”. In this mode, you • “Main Menu” (to switch to the main menu) may say the following commands: Satellite Radio •...
Page 136
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Switch to system setup” − “Continue” (to continue recording) • “Change to setup” − “Delete” (to delete the recording) • “Play Memos” (to play previously recorded memos) • “Main menu setup” or —...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Voice Training SEATS For users experiencing difficulty with the system recog- Seats are a part of the Occupant Restraint System of the nizing their voice commands or numbers the Uconnect™ vehicle. Voice “Voice Training” feature may be used. WARNING! 1.
Page 138
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE power seat switches that are used to control the move- Adjusting The Seat Forward Or Rearward ment of the seat cushion and the seatback. The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Reclining The Seatback WARNING! (Continued) The angle of the seatback can be adjusted forward or • Do not ride with the seatback reclined so that the rearward. Push the seatback switch forward or rearward, shoulder belt is no longer resting against your the seat will move in the direction of the switch.
Page 140
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjusting The Seat Forward Or Rearward WARNING! The seat can be adjusted both forward and rearward. • Adjusting a seat while driving may be dangerous. Push the seat switch forward or rearward, the seat will move in the direction of the switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.
Page 142
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE controls for each seat are located near the bottom center WARNING! of the instrument panel (below the climate controls). • Persons who are unable to feel pain to the skin You can choose from HIGH, LOW or OFF heat settings. because of advanced age, chronic illness, diabetes, Amber indicator lights in each switch indicate the level of spinal cord injury, medication, alcohol use, ex-...
Page 143
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 The heated seats switch from HIGH to LOW and from Rear Heated Seats LOW to OFF automatically, based on time and tempera- On some models, the two outboard seats are equipped ture of the seat. The heated seats can operate on HIGH with heated seats.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: small fans that draw the air from the passenger compart- • Once a heat setting is selected, heat will be felt within ment and blow air through fine perforations in the seat two to five minutes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Vehicles Equipped With Remote Start On models equipped with remote start, the drivers ventilated seat can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in “Things to Know Before Starting Your Vehicle”...
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! WARNING! • Do not stand or lean in front of the seat while Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. actuating the handle.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mega Cab Rear Seat Features WARNING! Reclining Rear Seats — If Equipped Do not ride with the seatback reclined so that the The recliner handle is located on the outside of the seat shoulder belt is no longer resting against your chest.
Page 149
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Table Mode Handle Table Mode 2. Fold the seatback forward. 3. Lift the seatback, to return the seat to the upright position. Be sure the seatback is locked in place. Folding Rear Seat — If Equipped Both the outboard rear seats will drop and move forward when the seatback is folded flat.
Page 150
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To fold either rear seat flat: WARNING! 1. Lift the handle, located on the outboard side of either • It is dangerous to ride in a cargo area, inside or of the rear seats. outside of a vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 WARNING! An improperly latched seat could cause serious in- jury or death. Make sure that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.
Page 152
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision.
Page 153
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Rear Head Restraints NOTE: • The rear center head restraint (Crew Cab and Quad The two outboard seat are equipped with adjustable head restraints. To raise the head restraint, pull upward on the Cab) has only one adjustment position that is used to head restraint.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER MEMORY SEAT — IF EQUIPPED and radio station preset settings. Your Remote Keyless The memory seat buttons are located on the outboard Entry (RKE) transmitters can also be programmed to side of the drivers seat cushion. recall the same positions when the UNLOCK button is pressed.
Page 155
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 1. Insert the ignition key, and turn the ignition switch to 7. Press and release the S (SET) button located on the the ON/RUN position. driver’s door. 2. Press the driver door MEMORY button number 1 if 8.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 12. Repeat the above steps to set the next memory A recall can be cancelled by pressing any of the position, using the other numbered memory button, or to MEMORY buttons on the drivers seat during a recall (S, link another RKE transmitter to memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 5. Within five seconds, press and release the UNLOCK greater than or equal to 2.67 in (68 mm) forward of the button on the RKE transmitter. To disable another RKE rear seat stop when the key is removed from the transmitter linked to either memory position, repeat ignition switch.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Each stored memory setting will have an associated Easy Entry/Exit position. NOTE: The Easy Entry/Exit feature is not enabled when the vehicle is delivered from the factory. The Easy Entry/Exit feature is enabled (or later disabled) through the programmable features in the Electronic Vehicle Information Center (EVIC).
Page 159
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. WARNING! Be sure the hood is fully latched before driving your vehicle.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Your vehicle is equipped with plastic headlight and fog The headlight switch is located on the left side of the light (if equipped) lenses that are lighter and less suscep- instrument panel, next to the steering wheel. The head- tible to stone breakage than glass lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Headlights To turn on the headlights, rotate the headlight switch clockwise to the headlight position. When the headlight switch is on, the parking lights, taillights, license plate light and instru- ment panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the O (Off) position.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The engine must be running before the head- delay can be cancelled by either turning the headlight lights will turn on in the Automatic Mode. switch on then off, or by turning the ignition ON. Headlights On With Wipers (Available With The headlight delay time is programmable on vehicles Automatic Headlights Only)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 turn off when the switch is pushed a second time, when the headlight switch is rotated to the off position, or the high beam is selected. Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the bottom of the switch) is rotated to the far right detent position, or if equipped, when the UNLOCK...
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE supplement the brightness of the odometer, trip odom- Cargo Light eter, radio and overhead console by rotating the control The cargo lights are turned on by pressing on the cargo to the right until you hear a click. This feature is termed button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Lights-On Reminder Daytime Running Lights (DRL) — If Equipped If the headlights, parking lights, or cargo lights are left on The headlights on your vehicle will illuminate when the after the ignition is turned OFF, a chime will sound when engine is started and the transmission is in any gear the driver’s door is opened.
Page 166
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals NOTE: If either light remains on and does not flash, or Move the multifunction lever up or down and the arrows there is a very fast flash rate, check for a defective outside on each side of the instrument cluster flash to show light bulb.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 High/Low Beam Switch WINDSHIELD WIPERS AND WASHERS Push the multifunction lever toward the instrument Windshield Wipers panel to switch the headlights to high beam. Pulling the The wipers and washers are operated by a switch in the multifunction back toward the steering wheel will turn multifunction lever.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Windshield Washers Rotate the end of the lever upward, to the first detent past To use the windshield washer, push the washer knob, the intermittent settings for low-speed wiper operation. located on the end of the multifunction lever, inward to Rotate the end of the lever upward to the second detent the second detent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 NOTE: The mist feature does not activate the washer WARNING! pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to Sudden loss of visibility through the windshield spray the windshield with washer fluid.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pull the lever toward the steering wheel to unlock the WARNING! steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Do not adjust the steering column while driving. Release the lever to lock the steering column firmly in Adjusting the steering column while driving or driv- place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 The heated steering wheel switch is located on the switch WARNING! bank below the climate controls. • Persons who are unable to feel pain to the skin Press the switch to turn on the heated because of advanced age, chronic illness, diabetes, steering wheel.
Page 172
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals cannot be adjusted when the vehicle is in from the driver to provide improved position with the steering wheel. REVERSE or when the Electronic Speed Control Sys- tem is on. The following messages will be displayed The adjustable pedal switch is located to the left side of on vehicles equipped with the Electronic Vehicle In- the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 WARNING! Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident. Always adjust the pedals while the vehicle is parked. ELECTRONIC SPEED CONTROL When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h).
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE System can be reactivated by pushing the Electronic To Set A Desired Speed Speed Control ON/OFF button and resetting the desired Turn the Electronic Speed Control ON. When the vehicle vehicle set speed. has reached the desired speed, press the SET (-) button and release.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 To Resume Speed decrease until the button is released. Release the button To resume a previously set speed, push the RES (+) when the desired speed is reached, and the new set speed button and release.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE On steep hills, a greater speed loss or gain may occur so Usage Precautions for limitations of this system and it may be preferable to drive without Electronic Speed recommendations. Control. ParkSense will retain the last system state (enabled or disabled) from the last ignition cycle when the ignition is WARNING! changed to the ON/RUN position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 (200 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orienta- tion of the obstacle. ParkSense Warning Display The ParkSense Warning screen will only be displayed if Sound and Display is selected from the Customer- Pro- grammable Features section of the Electronic Vehicle Information Center (EVIC).
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense Display When the vehicle is in REVERSE, the warning display will turn ON indicating the system status. Park Assist System Off The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the EVIC Park Assist System On display will show fewer arcs and the sound tone will...
Page 179
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Slow Tone Fast Tone...
Page 180
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: Continuous Tone...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 WARNING ALERTS Rear Distance Greater than 79-39 in 39-25 in 25-12 in Less than (in/cm) 79 in (200 cm) (200-100 cm) (100-65 cm) (65-30 cm) 12 in (30 cm) Audible Alert None Single 1/2 Slow Fast Continuous...
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE display the “PARK ASSIST SYSTEM OFF” message for Your Instrument Panel” for further information. When approximately five seconds. Refer to “Electronic Vehicle the shift lever is moved to REVERSE and the system has Information Center (EVIC)”...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 • When you move the shift lever to the REVERSE Cleaning The ParkSense System Clean the ParkSense sensors with water, car wash soap position and ParkSense is turned off, the instrument and a soft cloth. Do not use rough or hard cloths. Do not cluster will display “PARK ASSIST SYSTEM OFF”...
Page 184
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Objects such as bicycle carriers, trailer hitches, etc., CAUTION! must not be placed within 12 in (30 cm) from the rear • ParkSense is only a parking aid and it is unable fascia/bumper while driving the vehicle.
Page 185
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 WARNING! WARNING! (Continued) • Before using the ParkSense Rear Park Assist • Drivers must be careful when backing up even System, it is strongly recommended that the ball when using the ParkSense Rear Park Assist Sys- mount and hitch ball assembly is disconnected tem.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKVIEW REAR BACK UP CAMERA — IF When displayed, static grid lines will illustrate the width EQUIPPED of the vehicle while a dashed center-line will indicate the Your vehicle may be equipped with the ParkView Rear center of the vehicle to assist with aligning to a hitch/ Back Up Camera that allows you to see an on-screen receiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 WARNING! CAUTION! (Continued) • To avoid vehicle damage, the vehicle must be Drivers must be careful when backing up even when driven slowly when using ParkView to be able to using the ParkView Rear Back Up Camera. Always stop in time when an obstacle is seen.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Power Sunroof Switch — If Equipped 4. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key and pressing the • Power Sliding Rear Window Switch — If Equipped “save”...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Courtesy/Reading Lights Both lights in the overhead console and rear passenger compartment will illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (full right position), or when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter, if equipped.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED HomeLink replaces up to three hand-held transmitters that operate devices such as garage door openers, motor- ized gates, lighting or home security systems. The HomeLink unit is powered by your vehicles 12 Volt battery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 Before You Begin Programming HomeLink Be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink system.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Erasing all channels should only be performed when programming HomeLink for the first time. Do not erase channels when programming additional buttons. • If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance.
Page 193
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 3. Simultaneously press and hold both the Homelink On some garage door openers/devices there may be a button you want to program and the hand-held transmit- light that blinks when the garage door opener/device is ter button.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink Button 2. Place the hand-held transmitter 1 to 3 inches (3 to To reprogram a channel that has been previously trained, 8 cm) away from the HomeLink button you wish to follow these steps: program.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 5. Press and hold the programmed HomeLink button. Canadian/Gate Operator Programming The EVIC will display “CHANNEL # TRANSMIT”. If the For programming transmitters in Canada/United States garage door opener/device activates, programming is that require the transmitter signals to “time-out” after complete.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Simultaneously press and hold both the Homelink Reprogramming A Single HomeLink Button button while you press and release (“cycle”), your hand- To reprogram a channel that has been previously trained, held transmitter every two seconds. follow these steps: 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 Security Troubleshooting Tips It is advised to erase all channels before you sell or turn If you are having trouble programming HomeLink , here in your vehicle. are some of the most common solutions: •...
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information WARNING! This device complies with FCC rules Part 15 and Industry • Your motorized door or gate will open and close Canada RSS-210. Operation is subject to the following two conditions: while you are programming the universal trans- ceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located on the overhead • Never leave children alone in a vehicle. Leaving console between the courtesy/reading lights. unattended children in a vehicle is dangerous for a number of reasons.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Open Sunroof — Express Mode Pinch Protect Feature Press the switch rearward and release it and the sunroof This feature will detect an obstruction in the opening of will open automatically from any position. The sunroof the sunroof during Express Close operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 Venting Sunroof — Express the rear windows open, open the front and rear windows Press and release the “Vent” button, and the sunroof will together to minimize the buffeting. If the buffeting occurs open to the vent position.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE time is programmable. Refer to “Electronic Vehicle Infor- CAUTION! mation Center (EVIC)/Personal Settings (Customer- • Do not exceed the maximum power of 160 Watts Programmable Features)” in “Understanding Your In- strument Panel” for further information. (13 Amps) at 12 Volts.
Page 203
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 • Inside the top storage tray — with floor mounted • Inside the upper lid of the center storage compartment shifter. — if equipped. Power Outlet — Floor Shifter Power Outlet — Upper Lid...
Page 204
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Rear of the center console storage compartment — The key symbol indicates that this outlet can supply Quad Cab or Crew Cab. power when the key is in the ON/RUN or ACC posi- tions.
Page 205
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. •...
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER — IF CAUTION! EQUIPPED • Many accessories that can be plugged in draw A removable ash receiver and cigar lighter are available. For vehicles with a bench seat the cupholder tray can be power from the vehicle’s battery, even when not in used to hold the ash receiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 For vehicles equipped with an optional floor shifter. POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the center stack of the instrument panel, to the right of the radio.
Page 208
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 NOTE: CUPHOLDERS • When the power inverter switch is pressed, there will Front Instrument Panel Cupholders — be a delay of approximately one second before the (40–20–40 Seats) power inverter status indicator turns on. The status The cupholders are located in the pull-out tray at the indicator of the AC power inverter indicates whether bottom of the center stack.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Instrument Panel Cupholders — Floor Rear Cupholder — Quad Cab Mounted Shifter Quad Cab vehicles may be equipped with a rear cup- For vehicles equipped with bucket seats and a floor holder that consists of two cup wells for rear passenger mounted shifter there are two cupholders located in the convenience.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 Rear Cupholder — Crew Cab STORAGE Crew Cab vehicles are equipped with rear cupholders Glove Box Storage The glove box is located on the passenger side of the located in the center armrest. instrument panel and features both an upper and lower storage area.
Page 212
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper glove box push upward on the handle To open the lower glove box, pull on the handle to release release. The glove box door will automatically open. the latch and lower the door. Upper Glove Box Lower Glove Box...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 Door Storage Rear Door Storage — Crew Cab Storage compartments are located in both the driver and Front Door Storage — If Equipped passenger door trim panels. Storage areas and bottle holders (drivers side only) are located in the door trim panels.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Center Storage Compartment — If Equipped WARNING! The center storage compartment is located between the • This armrest is not a seat. Anyone seated on the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and armrest could be seriously injured during vehicle lower storage area.
Page 215
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 Upper Storage Compartment Lower Storage Bin With the upper lid closed, pull on the lower handle to open the lower storage bin.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 NOTE: The front seat may have to be moved forward to Seatback Storage fully open the lid. Located in the back of both the driver and passenger front seats are pockets that can be used for storage. Opened Storage Bin Drivers Side Seatback Storage...
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage (Regular Cab) Storage and Seats (Crew Cab) The storage bin is located behind the front seats and runs The Crew Cab models provide additional storage under the length of the cab. the rear seats. Lift the seats to access the storage com- partment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 CAUTION! Always lift the storage compartment lids by using the handle. Failure to lift the lids by using the handle can result in damage to the lids. Plastic Grocery Bag Retainers (Regular Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind...
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES CAUTION! Rear Window Defroster Failure to follow these cautions can cause damage to The rear window defroster button is located on the the heating elements: climate control panel. Press this button to turn on •...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 Power Sliding Rear Window — If Equipped Manual Sliding Rear Window — If Equipped The switch for the power sliding rear window is located A locking device in the center of the window helps to on the overhead console.
Page 222
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position. Load Floor In Open Position 3. Reverse the procedure to store the load floor. Unfolding The Load Floor 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position.
Page 223
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3.
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE RAMBOX — IF EQUIPPED The RamBox system is an integrated pickup box storage and cargo management system consisting of three fea- tures: • Integrated box side storage bins • Cargo extender/divider • Bed rail tie-down system RamBox Integrated Box Side Storage Bins Cargo storage bins are located on both sides of the pickup box.
Page 225
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 CAUTION! Failure to follow the following items could cause damage to the vehicle: • Assure that all cargo inside the storage bins is properly secured. • Do not exceed cargo weight rating of 150 lb (68 kg) per bin.
Page 226
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The interior of the RamBox will automatically illumi- CAUTION! nate when the lid is opened. In addition to the automatic illumination switch, there is a manual on/off switch Leaving the lid open for extended periods of time located at the rear of each storage bin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 RamBox Safety Warning CAUTION! (Continued) Carefully follow these warnings to help prevent personal • Loads applied to the top of the bin lid should be injury or damage to your vehicle: minimized to prevent damage to the lid and latching/hinging mechanisms.
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE RamBox Storage Bin Cover Emergency Release NOTE: In the event of an individual being locked inside Lever — If Equipped the storage bin, the storage bin cover can be opened from As a security measure, a Storage Bin Cover Emergency inside of the bin by pulling on the glow-in-the-dark lever Release is built into the storage bin cover latching mecha- attached to the storage bin cover latching mechanism.
Page 229
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 Storage Position The storage position for the bed extender is at the front of the truck bed which maximizes the bed cargo area when not in use. To install the bed extender into the storage position, perform the following: 1.
Page 230
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. With the side gates open, position the extender fully 3. Rotate the side gates closed allowing the outboard forward in the bed against the front panel. ends to be positioned in front of the cargo tie down loops. Storage Position Cargo Tie Down Loop...
Page 231
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 4. Rotate the center handle horizontally to secure the side 5. Lock the center handle using the vehicle key to secure gates in the closed position. the panel into place and assist against theft. Divider Position The divider position is intended for managing your cargo and assisting in keeping cargo from moving around the...
Page 232
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To install the bed extender into a divider position per- form the following: 1. Make sure the center handle is unlocked using the vehicle key and rotate the center handle vertically to release the extender side gates. Center Handle And Lock 1 —...
Page 233
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 Aligning Gate To Slots Side Gates Closed 3. Rotate the side gates closed so that the outboard ends 5. Lock the center handle to secure the panel into place are secured into the intended slots of the bed. and assist against theft.
Page 234
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE additional cargo room is needed. The extender position 2. Make sure the center handle is unlocked and rotate the utilizes a locating pin and rotating handle located on both center handle vertically in order to release the extender sides of the truck bed near the tailgate.
Page 235
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 4. Rotate the handles to the horizontal position to secure WARNING! into place. To reduce the risk of potential injury or property damage: • Cargo must be secured. • Do not exceed cargo load rating of your vehicle. •...
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Bed Rail Tie-Down System CAUTION! The maximum load per cleat should not exceed 250 lbs (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.
Page 237
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 To move the cleat to any position on the rail, turn the nut To remove the cleats from the utility rail, remove the end counterclockwise, approximately three turns. Then pull cap by pushing up on the locking tab, located on the out on the cleat and slide it to the detent nearest the bottom of the end cap.
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SLIDE-IN CAMPERS Disconnecting the Rear Camera — If Equipped Camper Applications 1. Open the tailgate to access the rear camera connector Certain truck models are not recommended for slide-in bracket located on the rear sill. campers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 5. Connect the tailgate plug (provided in the glove box) to the tailgate wiring harness to ensure that the terminals do not corrode. 6. Tape the tailgate harness and bracket against the forward-facing surface of the tailgate. This will prevent damaging the connector and bracket when storing or reinstalling the tailgate.
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Make sure tailgate is supported when removing 5. Slide the entire tailgate to the right to free the left side support cables. pivot. 6. Remove the tailgate from the vehicle. NOTE: Do not carry the tailgate loose in the truck pickup box.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....243 Electronic Vehicle Information Center (EVIC) — If Equipped ......266 Switch Bank Button Description .
240 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Compass / Temperature Display ..278 ▫ Operation Instructions - Auxiliary Mode ..296 ▫ Customer-Programmable Features Media Center 130 With Satellite Radio (System Setup) .
Page 243
UNDERSTANDING YOUR INSTRUMENT PANEL 241 ▫ Listen To An Audio Source On Channel 2 iPod /USB/MP3 Control — If Equipped ..312 While A Video Is Playing On Channel 1 ..325 ▫ Connecting The iPod Or External USB ▫...
244 UNDERSTANDING YOUR INSTRUMENT PANEL SWITCH BANK BUTTON DESCRIPTION 1. TOW/HAUL Refer to “Starting And Operating” for more information. Upper Switch Bank 2. ESC OFF The upper switch bank is located on the center of the Refer to “Starting And Operating” for more information. instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 6. TPMS LIGHT LOAD — IF EQUIPPED 1. HEATED SEATS Refer to “Starting And Operating” for more information. Refer to “Understanding The Features Of Your Vehicle” for more information. Lower Switch Bank 2. VENTILATED SEATS The lower switch bank is located on the center of the Refer to “Understanding The Features Of Your Vehicle”...
248 UNDERSTANDING YOUR INSTRUMENT PANEL • Check for an inoperative outside light bulb if either INSTRUMENT CLUSTER DESCRIPTIONS indicator remains on and does not flash, or flashes at a 1. Tachometer rapid rate. The tachometer indicates engine speed in Revolutions Per Minute (RPM x 1000).
Page 251
UNDERSTANDING YOUR INSTRUMENT PANEL 249 CAUTION! WARNING! Driving with a hot engine cooling system could A hot engine cooling system is dangerous. You or damage your vehicle. If the temperature gauge reads others could be badly burned by steam or boiling “H”...
Page 252
250 UNDERSTANDING YOUR INSTRUMENT PANEL rotate at the same speed. Low range provides a greater If the light remains lit with the engine running, your gear reduction ratio to provide increased torque at the vehicle will usually be drivable; however, see an autho- wheels.
Page 253
UNDERSTANDING YOUR INSTRUMENT PANEL 251 9. 4WD Auto Indicator 11. TOW/HAUL The 4WD auto indicator will be illuminated The TOW HAUL button is located on the whenever the four-wheel drive mode is auto- center stack upper switch bank. This light will matically engaged.
Page 254
252 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: 14. Oil Pressure Gauge • The “ESC Off Indicator Light” and the “ESC The pointer should always indicate some oil pressure Activation/Malfunction Indicator Light” come on mo- when the engine is running. A continuous high or low mentarily each time the ignition switch is turned to reading under normal driving conditions may indicate a ON/RUN.
Page 255
UNDERSTANDING YOUR INSTRUMENT PANEL 253 16. Odometer Display / Electronic Vehicle Information The two trip odometers show individual trip mileage. To Center (EVIC) Display Area — If Equipped switch from odometer to trip odometers, press and release the TRIP ODOMETER button. Odometer Display The odometer display shows the total distance the ve- To reset a trip odometer, display the desired trip odom-...
Page 256
254 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: There is also an engine hour function. This modify driving habits in order to increase fuel economy. indicates the total number of hours the engine has been The ECO display will toggle between ECO and ECO-ON running.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 A loose, improperly installed, or damaged fuel filler cap change indicator system is duty cycle-based, which may also turn on the Malfunction Indicator Light (MIL). means the engine oil change interval may fluctuate dependent upon your personal driving style. LoW tirE When the appropriate condition exists, the odometer Unless reset, this message will continue to display each...
Page 258
256 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the indicator message illuminates when you service. Refer to “If Your Engine Overheats” in “What To start the vehicle, the oil change indicator system did not Do In Emergencies” for further information. reset. If necessary, repeat this procedure. For vehicles equipped with a premium cluster this indi- 17.
Page 259
UNDERSTANDING YOUR INSTRUMENT PANEL 257 19. Low Fuel Light moves to either extreme left or right and remains there When the fuel level reaches approximately 3.0 gal during normal driving, the electrical system should be (11.0 L) this light will turn on, and remain on until serviced.
Page 260
258 UNDERSTANDING YOUR INSTRUMENT PANEL 23. Brake Warning Light The dual brake system provides a reserve braking capac- This light monitors various brake functions, ity in the event of a failure to a portion of the hydraulic including brake fluid level and parking brake system.
Page 261
UNDERSTANDING YOUR INSTRUMENT PANEL 259 The light also will turn on when the parking brake is WARNING! applied with the ignition switch in the ON/RUN posi- tion. Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. NOTE: This light shows only that the parking brake is It will take longer to stop the vehicle.
Page 262
260 UNDERSTANDING YOUR INSTRUMENT PANEL Center (EVIC). Refer to ”Electronic Vehicle Information possible, and inflate them to the proper pressure. Driving Center (EVIC) — If Equipped” for further information. on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also 25.
Page 263
UNDERSTANDING YOUR INSTRUMENT PANEL 261 When the malfunction indicator is illuminated, the sys- CAUTION! tem may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety The TPMS has been optimized for the original of reasons, including the installation of replacement or equipment tires and wheels.
Page 264
262 UNDERSTANDING YOUR INSTRUMENT PANEL 26. Malfunction Indicator Light (MIL) Although your vehicle will usually be drivable and not The Malfunction Indicator Light (MIL) is part of need towing, see your authorized dealer for service as an onboard diagnostic (OBDII) system which soon as possible.
Page 265
UNDERSTANDING YOUR INSTRUMENT PANEL 263 28. Front Fog Light Indicator — If Equipped WARNING! This indicator will illuminate when the front fog lights are on. A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal 29. Anti-Lock Brake (ABS) Light operating conditions.
Page 266
264 UNDERSTANDING YOUR INSTRUMENT PANEL 30. Transmission Temperature Warning Light WARNING! This light indicates that there is excessive trans- mission fluid temperature that might occur If the Transmission Temperature Warning Light is with severe usage such as trailer towing. It may illuminated and you continue operating the vehicle, also occur when operating the vehicle in a high in some circumstances you could cause the fluid to...
Page 267
UNDERSTANDING YOUR INSTRUMENT PANEL 265 31. Seat Belt Reminder Light vehicle is experiencing a problem with the charging When the ignition switch is first turned to ON/ system. Obtain SERVICE IMMEDIATELY. See an autho- RUN, this light will turn on for four to eight rized dealer.
266 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER NOTE: • The compass on your vehicle is self-calibrating, elimi- (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) fea- nating the need to manually calibrate the compass. tures a driver-interactive display that is located in the •...
UNDERSTANDING YOUR INSTRUMENT PANEL 267 • Customer Programmable Features (System Setup) Press and release the DOWN button to scroll downward through the main menus and sub- • Trip Information (in Odometer line) menus. SELECT Button Press and release the SELECT button for access to main menus or sub-menus.
Page 270
268 UNDERSTANDING YOUR INSTRUMENT PANEL • Right front turn signal lamp out • Wrong Key • Left rear turn signal lamp out • Damaged Key • Right rear turn signal lamp out • Key not programmed • Service air filter •...
Page 271
UNDERSTANDING YOUR INSTRUMENT PANEL 269 • Remote start aborted — Fuel low • Blind spot detection unavailable • Remote start active — Key to Run • Automatic High Beams on • Remote start disabled — System fault • Automatic High Beams off •...
Page 272
270 UNDERSTANDING YOUR INSTRUMENT PANEL • Memory 1 Profile Recall Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. • Memory 2 Profile Recall The engine oil level must be checked under the hood. •...
Page 273
UNDERSTANDING YOUR INSTRUMENT PANEL 271 • Electronic Speed Control Light If the light remains lit with the engine running, your This light will turn on when the electronic vehicle will usually be drivable. However, see an autho- speed control is ON. rized dealer for service as soon as possible.
Page 274
272 UNDERSTANDING YOUR INSTRUMENT PANEL shift the transmission into NEUTRAL and idle the ve- light comes on, stop the vehicle and run the engine at idle hicle. If the temperature reading does not return to or faster, with the transmission in NEUTRAL until the normal, turn the engine off immediately and call for light goes off.
Page 275
UNDERSTANDING YOUR INSTRUMENT PANEL 273 • Loose Gascap Indicator indicator system is duty-cycle based, which means the If the vehicle diagnostic system determines engine oil change interval may fluctuate dependent upon that the fuel filler cap is loose, improperly your personal driving style. installed, or damaged, a loose gascap indicator Unless reset, this message will continue to display each will display in the telltale display area.
274 UNDERSTANDING YOUR INSTRUMENT PANEL Fuel Economy / Fuel Saver Mode / Distance To Empty (DTE) — If Equipped Average Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “0” or show dashes for two seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 275 This estimated distance is determined by a weighted Trip Functions average of the instantaneous and average fuel economy, Press and release the ODOMETER/TRIP ODOMETER according to the current fuel tank level. DTE cannot be button until one of the following Trip Functions display reset through the RETURN button.
276 UNDERSTANDING YOUR INSTRUMENT PANEL • Trip B Vehicle Info (Customer Information Features) Shows the total distance traveled for Trip B since the last Press and release the UP or DOWN button until “Vehicle reset. Info” displays in the EVIC and press the SELECT button. Press the UP and DOWN button to scroll through the •...
UNDERSTANDING YOUR INSTRUMENT PANEL 277 • Trailer Brake — If Equipped Displays trailer brake output power and trailer brake status indicator. • Engine Hours Displays the number of hours of engine operation. Tire PSI Press and release the UP or DOWN button until “Tire PSI”...
278 UNDERSTANDING YOUR INSTRUMENT PANEL • Your system can be set to display pressure units in PSI, NOTE: • The system will display the last known outside tem- kPa, or BAR. perature when starting the vehicle and may need to be Units driven several minutes before the updated tempera- Press and release the UP or DOWN button until “Units”...
Page 281
UNDERSTANDING YOUR INSTRUMENT PANEL 279 mode. Both the outside temperature display and ATC Manual Compass Calibration operation will return to normal when the snowplow is If the compass appears erratic and the CAL indicator removed. does not appear in the EVIC display, you must put the compass into the Calibration Mode manually, as follows: Automatic Compass Calibration This compass is self-calibrating, which eliminates the...
Page 282
280 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “CAL” indicator turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between Magnetic North and Geographic North.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 3. Press the DOWN button until the “Compass Variance” Use the UP or DOWN button to display one of the message is displayed in the EVIC, then press the SELECT following choices. button. The last variance zone number displays in the Select Language EVIC.
Page 284
282 UNDERSTANDING YOUR INSTRUMENT PANEL the feature showing the system has been activated or the Auto Unlock Doors check-mark is removed showing the system has been When this feature is selected, all doors will unlock when deactivated. the vehicle is stopped and the transmission is in the PARK or NEUTRAL position and the driver’s door is Park Assist System opened.
Page 285
UNDERSTANDING YOUR INSTRUMENT PANEL 283 scroll up or down until the preferred setting is high- seat features will automatically turn on when tempera- lighted, then press and release the SELECT button until a tures are below 40° F (4.4° C). When temperatures are check-mark appears next to the setting, showing that the above 80°...
Page 286
284 UNDERSTANDING YOUR INSTRUMENT PANEL Sound Horn With Lock Headlamp Off Delay When this feature is selected, a short horn sound will When this feature is selected, the driver can choose to occur when the RKE transmitter LOCK button is pressed. have the headlights remain on for 0, 30, 60, or 90 seconds This feature may be selected with or without the Flash when exiting the vehicle.
Page 287
UNDERSTANDING YOUR INSTRUMENT PANEL 285 Automatic High Beams — If Equipped been deactivated. When this feature is deactivated, the When this feature is selected, the high beam headlights system reverts to the standard intermittent wiper will deactivate automatically under certain conditions. To operation.
Page 288
286 UNDERSTANDING YOUR INSTRUMENT PANEL Key-Off Power Delay Hill Start Assist (HSA) When this feature is selected, the power window When on is selected, the HSA system is active. Refer to switches, radio, hands-free system (if equipped), DVD “Electronic Brake Control System” in “Starting And video system (if equipped), power sunroof (if equipped), Operating”...
UNDERSTANDING YOUR INSTRUMENT PANEL 287 Trailer Brake Type MEDIA CENTER 730N/430/430N (RHR/RER/RBZ/ When this feature is selected, the Trailer Brake Type can RHB) CD/DVD/HDD/NAV — IF EQUIPPED be changed between “Light Electric” and “Heavy Elec- NOTE: The sales code is located on the lower right side tric”.
288 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 (SALES CODE RES) Operating Instructions — Radio Mode NOTE: The radio sales code is located on the lower right NOTE: The ignition switch must be in the ON or ACC side of the radio faceplate. position to operate the radio.
Page 291
UNDERSTANDING YOUR INSTRUMENT PANEL 289 SEEK Buttons 4. Adjust the minutes using the right side TUNE/ Press and release the SEEK buttons to search for the next SCROLL control knob. Press the TUNE/SCROLL control listenable station in AM/FM mode. Press the right switch knob to save time change.
Page 292
290 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second AM/FM Button time and MID will display. Turn the TUNE/SCROLL Press the buttons to select either AM or FM mode. control knob to the right or left to increase or decrease the SET/RND Button —...
UNDERSTANDING YOUR INSTRUMENT PANEL 291 • This radio is capable of playing compact discs (CD), and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by recordable compact discs (CD-R), rewritable compact pressing the pushbutton twice.
Page 294
292 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Ejecting with the ignition OFF is not allowed on CAUTION! convertible or soft-top models (if equipped). • This CD player will accept 4-3/4 in (12 cm) discs SEEK Button only. The use of other sized discs may damage the Press the right SEEK button for the next selection on the CD player mechanism.
UNDERSTANDING YOUR INSTRUMENT PANEL 293 AM/FM Button Supported Media (Disc Types) Press the button to select either AM or FM mode. The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Supported Medium Formats (File Systems) Random Play.
Page 296
294 UNDERSTANDING YOUR INSTRUMENT PANEL a number instead. With a maximum number of files, Supported MP3 File Formats exceeding 20 folders will result in this display. With The radio will recognize only files with the *.MP3 exten- 200 files, exceeding 50 folders will result in this sion as MP3 files.
Page 297
UNDERSTANDING YOUR INSTRUMENT PANEL 295 Playback of MP3 Files MPEG Specifi- Sampling Fre- Bit Rate (kbps) When a medium containing MP3 data is loaded, the cation quency (kHz) radio checks all files on the medium. If the medium 320, 256, 224, contains a lot of folders or files, the radio will take more MPEG-1 Audio 192, 160, 128,...
296 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode MEDIA CENTER 130 WITH SATELLITE RADIO The auxiliary (AUX) jack is an audio input jack, which (SALES CODE RES+RSC) allows the user to plug in a portable device, such as an NOTE: The radio sales code is located on the lower right MP3 player, or cassette player, and utilize the vehicle’s side of the radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL 297 Operating Instructions — Radio Mode to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make NOTE: The ignition switch must be in the ON/RUN or another selection.
Page 300
298 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button Uconnect™ Phone — If Equipped 3. After adjusting the hours, press the right side TUNE/ Press this button to operate the Uconnect™ Phone feature SCROLL control knob to set the minutes. The minutes (if equipped).
Page 301
UNDERSTANDING YOUR INSTRUMENT PANEL 299 INFO Button Push the rotary TUNE/SCROLL control knob a second Press the INFO button for an RDS station (one with call time and MID will display. Turn the TUNE/SCROLL letters displayed). The radio will return a Radio Text control knob to the right or left to increase or decrease the message broadcast from an FM station (FM mode only).
Page 302
300 UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button Program Type 16-Digit Character Display Pressing this button once will turn on the Music Type Information Inform mode for five seconds. Pressing the MUSIC TYPE button Jazz Jazz or turning the TUNE/SCROLL control knob within five News News seconds will allow the program format type to be se-...
Page 303
UNDERSTANDING YOUR INSTRUMENT PANEL 301 hours, press the TUNE/SCROLL control knob to set Program Type 16-Digit Character Display the minutes. The minutes will begin to blink. Adjust Top 40 Top 40 the minutes using the right side TUNE/SCROLL Weather Weather control knob.
302 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by Operation Instructions — CD MODE for CD and repeating the above procedure with this exception: Press MP3 Audio Play the SET/RND button twice and SET 2 will show in the NOTE: display window.
Page 305
UNDERSTANDING YOUR INSTRUMENT PANEL 303 If you insert a disc with the ignition ON/RUN and the If you have ejected a disc and have not removed it within radio ON, the unit will switch from radio to CD mode 10 seconds, it will be reloaded. If the CD is not removed, and begin to play when you insert the disc.
304 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Notes On Playing MP3 Files Press and hold FF (Fast Forward) and the CD player will The radio can play MP3 files; however, acceptable MP3 begin to fast forward until FF is released or RW or file recording media and formats are limited.
Page 307
UNDERSTANDING YOUR INSTRUMENT PANEL 305 • Maximum number of files: 255 Discs created with an option such as keep disc open after writing are most likely multisession discs. The use of • Maximum number of folders. (The radio display of file multisession for CD audio or MP3 playback may result in names and folder names is limited.
Page 308
306 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files MPEG Sampling Fre- Bit Rate (kbps) When a medium containing MP3 data is loaded, the Specification quency (kHz) radio checks all files on the medium. If the medium 320, 256, 224, contains a lot of folders or files, the radio will take more MPEG-1 Audio 192, 160, 128,...
UNDERSTANDING YOUR INSTRUMENT PANEL 307 LIST Button (CD Mode for MP3 Play) Press and hold the INFO button for three seconds or Pressing the LIST button will bring up a list of all folders more and the radio will display song titles for each file. on the disc.
308 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) radio system in your vehicle. Sirius will supply a wel- Press this button to change the display to time of day. The come kit that contains general information, including time of day will display for five seconds (when the how to setup your on-line listening account.
Page 311
UNDERSTANDING YOUR INSTRUMENT PANEL 309 using the TUNE/SCROLL control knob until Sirius ID is Reception Quality selected. Press the TUNE/SCROLL control knob and the Satellite reception may be interrupted due to one of the Sirius ID number will display. The Sirius ID number following reasons: display will time out in two minutes.
Page 312
310 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons RW/FF Press and release the SEEK buttons to search for the next Pressing the RW (Rewind) or FF (Fast Forward) buttons channel in Satellite mode. Press the right switch to seek causes the tuner to search for the next channel in the up and the left switch to seek down.
Page 313
UNDERSTANDING YOUR INSTRUMENT PANEL 311 By pressing the SEEK button when the Music Type Select the button (1-6) you wish to lock onto this channel function is active, the radio will be tuned to the next and press and release that button. If a button is not channel with the same selected Music Type name.
312 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions (Uconnect™ Phone) — If iPod control supports Mini, 4G, Photo, Nano, 5G iPod Equipped and iPhone devices. Some iPod software versions may Refer to “Uconnect™ Phone” in the Uconnect™ User not fully support the iPod control features. Please visit Manual located on the DVD for further details.
UNDERSTANDING YOUR INSTRUMENT PANEL 313 Connecting The iPod Or External USB Device NOTE: The glove compartment will have a position Use the connection cable to connect an iPod or external where the iPod or consumer electronic audio device USB device to the vehicle’s USB connector port which is cable can be routed through without damaging the cable located in the glove compartment.
314 UNDERSTANDING YOUR INSTRUMENT PANEL Using This Feature control mode, audio tracks (if available from audio By using iPod cable or external USB device to connect to device) start playing over the vehicle’s audio system. USB port: Play Mode • The audio device can be played on the vehicle’s sound When switched to iPod /USB/MP3 control mode, the system, providing metadata (artist, track title, album, iPod or external USB device automatically starts Play...
Page 317
UNDERSTANDING YOUR INSTRUMENT PANEL 315 • Jump backward in the current track by pressing and to the next screen of data for that track. Once all holding the << RW button. Holding the << RW screens have been viewed, the last INFO button press button long enough will jump to the beginning of will go back to the play mode screen on the radio.
316 UNDERSTANDING YOUR INSTRUMENT PANEL device, or press the VR button and say Shuffle ON or fast will scroll through the list faster. During fast Shuffle Off . If the RND icon is showing on the radio scroll, a slight delay in updating the information on display, then the shuffle mode is ON.
Page 319
UNDERSTANDING YOUR INSTRUMENT PANEL 317 • Preset 6 – Podcasts CAUTION! • Pressing a PRESET button will display the current • Leaving the iPod or external USB device (or any list on the top line and the first item in that list on supported device) anywhere in the vehicle in the second line.
318 UNDERSTANDING YOUR INSTRUMENT PANEL Bluetooth Streaming Audio (BTSA) 2. After the Ready prompt and the following beep, say Music can be streamed from your cellular phone to the Setup , then Select Audio Devices . Uconnect™ phone system. 3. Say the name of the audio device or ask the Controlling BTSA Using Radio Buttons Uconnect™...
UNDERSTANDING YOUR INSTRUMENT PANEL 319 • With the ignition switch in the ON or ACC position, UCONNECT™ MULTIMEDIA VIDEO ENTERTAINMENT SYSTEM (VES)™ — IF EQUIPPED turn the radio on by pushing the ON/OFF Volume Control knob. Getting Started • When the Video Screen are open and a DVD is inserted •...
Page 322
320 UNDERSTANDING YOUR INSTRUMENT PANEL Press the LOAD button then corresponding number (1–6) where the DVD is to be loaded (Non-Touch-Screen). 2. Insert the DVD with the label facing up. The radio automatically selects the appropriate mode after the disc is recognized and displays the menu screen or starts playing the first track.
Page 323
UNDERSTANDING YOUR INSTRUMENT PANEL 321 2. Touch the Rear VES soft-key to display the Rear VES NOTE: The “1” and “2” soft-keys are displayed for the Controls. If a channel list appears on the right side of the headphone channels. Touch 1 or 2 based on which screen, touch the HIDE LIST soft-key to display the Rear channel you want to change, select the new mode from VES Controls screen.
322 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Play Video Games • To view a DVD on the radio press the RADIO/MEDIA Connect the video game console to the Auxiliary RCA hard-key, on the radio faceplate, then touch the DISC input jacks located on the back of the center console. tab soft-key and then the VIEW VIDEO soft-key.
Page 325
UNDERSTANDING YOUR INSTRUMENT PANEL 323 When connecting an external source to the AUX input, be sure to follow the standard color coding for the VES™ jacks: NOTE: Certain high-end video games, such as Playsta- tion3 and XBox360 will exceed the power limit of the vehicle’s Power Inverter.
Page 326
324 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Touch-Screen Radio Controls 3. Touch the 1 or 2 based on the headphone channel you want to change. To exit press the back arrow soft-key at 1. Press the MENU hard-key on the radio faceplate. the top of the screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 325 Listen To An Audio Source On Channel 2 While A Video Is Playing On Channel 1 Ensure the Remote Control and Headphone switch is on Channel 2. Using The Remote Control 1. Press the MODE button on the Remote Control and the Mode Select Screen will display, unless a video is playing then only a small banner will appear on the bottom of the screen.
Page 328
326 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Touch-Screen Radio Controls 3. To listen to an audio source on Channel 2 while a video is playing on Channel 1, touch the 2 soft-key and 1. Press the MENU hard-key on the radio faceplate. choose an audio source.
UNDERSTANDING YOUR INSTRUMENT PANEL 327 Important Notes For Single Video Screen System Play A DVD Using The Touch-Screen Radio • VES™ is able to transmit two channels of stereo audio 1. Press the OPEN/CLOSE or LOAD hard-key on the simultaneously. radio faceplate (Touch-Screen).
Page 330
328 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Remote Control NOTE: • Channel/Screen 1 select mode information is shown 1. Press the MODE button on the Remote Control. on the left side of the screen. 2. While looking at Screen 1, highlight DISC by either •...
Page 331
UNDERSTANDING YOUR INSTRUMENT PANEL 329 NOTE: • To view a DVD on the radio press the RADIO/MEDIA hard-key, on the radio faceplate, then touch the DISC tab soft-key and then the VIEW VIDEO soft-key. • Viewing a DVD on the Touch-Screen radio screen is not available in all states/provinces, and the vehicle must be stopped, and the shift lever must be in the PARK position for vehicles with automatic transmis-...
330 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Control 2. Channel Selector Indicators – When a button is pressed, the currently affected channel or channel button is illuminated momentarily. 3. Light – Turns the remote control backlighting on or off. The remote backlighting turns off automatically after five seconds.
Page 333
UNDERSTANDING YOUR INSTRUMENT PANEL 331 / Prev – In radio modes, press to select to the disc in a radio with a multiple-disc changer, PROG Up previous station. In disc modes, press to advance to the selects the next disc and PROG Down selects the previ- start of the current or previous audio track or video ous disc.
332 UNDERSTANDING YOUR INSTRUMENT PANEL and the disc is stopped, press the SETUP button to access Remote Control Storage the DVD Setup menu. (see the DVD Setup Menu of this The video screen(s) come with a built in storage compart- manual.) ment for the remote control which is accessible when the screen is opened.
UNDERSTANDING YOUR INSTRUMENT PANEL 333 vehicle is not equipped with a DVD player, follow the radio’s instructions to turn Video Lock on. The radio and the video screen(s) indicate when Video Lock is active. • Pressing the Video Lock again or turning the ignition OFF turns Video Lock OFF and allows remote control operation of the VES™.
334 UNDERSTANDING YOUR INSTRUMENT PANEL Headphones Operation The headphones receive two separate channels of audio using an infrared transmitter from the video screen. Front seat occupants receive some headphone audio coverage to allow them to adjust the headphone volume for the young rear seat occupants that may not be able to do so for themselves.
Page 337
UNDERSTANDING YOUR INSTRUMENT PANEL 335 NOTE: The rear video system must be turned on before 2. Press the MODE button on the remote control. sound can be heard from the headphones. To conserve 3. If the video screen is displaying a video source (such battery life, the headphones will automatically turn off as a DVD Video), pressing STATUS shows the status on a approximately three minutes after the rear video system...
336 UNDERSTANDING YOUR INSTRUMENT PANEL Replacing The Batteries How Long Does The Coverage Last? This warranty lasts Each set of headphones requires two AAA batteries for as long as you own the Product. operation. To replace the batteries: What Does This Warranty Cover? Except as specified •...
UNDERSTANDING YOUR INSTRUMENT PANEL 337 NATURE WHATSOEVER. Some states and jurisdictions You may register your Unwired wireless headphones may not allow the exclusion or limitation of incidental or online at www.unwiredtechnology.com or by phone at consequential damages, so the above limitation may not 1-888-293-3332.
Page 340
338 UNDERSTANDING YOUR INSTRUMENT PANEL selected radio mode. When shared, the radio has priority Information Mode Display over the VES™ or all radio modes (FM, AM). The VES™ has the ability to switch tuner (AM/FM), SEEK, SCAN, TUNE, and recall presets in radio modes as long as it is not in shared mode.
Page 341
UNDERSTANDING YOUR INSTRUMENT PANEL 339 5. Channel 2 Shared Status Numeric Keypad Menu 6. Channel 2 Audio Only/Mute 7. Channel 1 ENTER Button Action 8. Channel 2 ENTER Button Action 9. Clock 10. Video Lock 11. Not Available / Error 12.
Page 342
340 UNDERSTANDING YOUR INSTRUMENT PANEL When the display for either Channel 1 or Channel 2 3. To delete the last digit, navigate to the Del button and shows DIRECT TUNE, pressing the remote control’s press the remote control’s ENTER button. ENTER button activates a numeric keypad menu.
Page 343
UNDERSTANDING YOUR INSTRUMENT PANEL 341 Disc Menu Display Settings Disc Menu For CDs Video Screen Display Settings When listening to a CD Audio or CD Data disc, pressing When watching a video source (DVD Video with the disc the remote control’s MENU button displays a list of all in Play mode, Aux Video, SIRIUS Backseat TV™, etc.), commands which control playback of the disc.
Page 344
342 UNDERSTANDING YOUR INSTRUMENT PANEL • Close the video screen. settings are already set for optimum viewing, so there is no need to change these settings under normal circum- • To change the current audio mode, press the remote stances. control’s MODE button.
Page 345
UNDERSTANDING YOUR INSTRUMENT PANEL 343 Disc Formats DVD Audio Support The VES™ DVD player is capable of playing the follow- When a DVD-Audio disc is inserted in the VES™ DVD ing types of discs (12 mm or 8 mm diameter): player, the DVD-Audio title on the disc is played by •...
Page 346
344 UNDERSTANDING YOUR INSTRUMENT PANEL • Mixed media recordable DVD formats will only play If you record a disc using a personal computer, there may be cases where the VES™ DVD player may not be able to the Video_TS portion of the disc. play some or the entire disc, even if it is recorded in a If you are still having trouble writing a disc that is compatible format and is playable on other players.
Page 347
UNDERSTANDING YOUR INSTRUMENT PANEL 345 • If you are creating your own files, the recommended end with the extension .mp3 or .MP3 and WMA files must always end with the extension .wma or fixed bit rate for MP3 files is between 96 and 192Kbps .WMA .
Page 348
346 UNDERSTANDING YOUR INSTRUMENT PANEL If a disc has a damaged track which results in audible or Display visible errors that persists for 2.0 seconds, the DVD Other Language Setup player will attempt to continue playing the disc by skipping forward 1.0 to 3.0 seconds at a time. If the end of the disc is reached, the DVD player will return to the beginning of the disc and attempt to play the start of the first track.
Page 349
UNDERSTANDING YOUR INSTRUMENT PANEL 347 • Using the remote control Up and Down cursor but- All of the Language settings have a special Other setting to accommodate languages other than Japanese or Eng- tons, select a digit for the current position. After lish.
Page 350
348 UNDERSTANDING YOUR INSTRUMENT PANEL Rating and Password Setup The default rating is Level 8 (play all discs without a password) and the default password is 0000. The Rating and Password settings work together to control the types of DVDs that your family watches. Most DVD- Video discs have a rating (from 1 to 8) assigned to them where lower numbers are designated for all audiences and higher numbers are designated for more adult audiences.
Page 351
UNDERSTANDING YOUR INSTRUMENT PANEL 349 • After the four-digit password is entered, press the To set the password, activate the DVD Setup Menu and follow these additional instructions: remote control’s ENTER button to accept the change. • Using the remote control Left and Right cursor but- tons, select the Rating tab.
Page 352
350 UNDERSTANDING YOUR INSTRUMENT PANEL • Using the remote control’s Up and Down cursor To set the rating, activate the DVD Setup Menu and follow these additional instructions: buttons, select the new rating level, and then press the remote control’s ENTER button to accept the change. •...
UNDERSTANDING YOUR INSTRUMENT PANEL 351 General Information This system complies with Part 15 of the FCC Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
352 UNDERSTANDING YOUR INSTRUMENT PANEL The button located in the center of the right hand control CD Player will switch modes to Radio, CD or other valid audio Pressing the top of the switch once will go to the next source.
UNDERSTANDING YOUR INSTRUMENT PANEL 353 2. If the disc is stained, clean the surface with a soft cloth, RADIO OPERATION AND MOBILE PHONES wiping from center to edge. Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from 3.
354 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: During snowplow usage on vehicles equipped with outside temperature display, the display may show higher temperatures than the outside ambient tempera- ture. The higher displayed temperature is due to blocked or reduced airflow to the underhood ambient tempera- ture sensor caused by the snowplow.
Page 357
UNDERSTANDING YOUR INSTRUMENT PANEL 355 Front Blower Control temperatures. Rotating the knob clockwise, into the red There are four blower speeds. Use this area, indicates warmer temperatures. control to regulate the amount of air NOTE: If your air conditioning performance seems forced through the system in any lower than expected, check the front of the A/C con- mode you select.
Page 358
356 UNDERSTANDING YOUR INSTRUMENT PANEL Panel Mode Mix Mode Air is directed through the outlets in the instrument Air is directed through the floor, defrost and side panel. These outlets can be adjusted to direct airflow. window demist outlets. This setting works best in cold or snowy conditions that require extra heat at Bi-Level Mode the windshield.
Page 359
UNDERSTANDING YOUR INSTRUMENT PANEL 357 • In cold or damp weather, the use of the Recirculation Recirculation Control Press this button to choose between mode will cause windows to fog on the inside because outside air intake or recirculation of of moisture buildup inside the vehicle.
358 UNDERSTANDING YOUR INSTRUMENT PANEL Economy Mode MAX A/C If ECONOMY mode is desired, press the A/C button to For maximum cooling, when MAX turn off the LED indicator and the A/C compressor. A/C is selected the A/C is turned on Rotate the temperature control knob to the desired automatically and the air is recircu- temperature.
Page 361
UNDERSTANDING YOUR INSTRUMENT PANEL 359 • When occupants in the vehicle select an Auto mode operation, Auto blower operation is set by using rotary knobs on the control unit and a comfort temperature setting by using the temperature up and down but- tons.
Page 362
360 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Operation NOTE: • It is not necessary to move the temperature settings for 1. Position the MODE control knob to the Auto position cold or hot vehicles. The system automatically adjusts on the Automatic Temperature Control (ATC) Panel. the temperature, mode and fan speed to provide 2.
Page 363
UNDERSTANDING YOUR INSTRUMENT PANEL 361 blower will engage immediately if the Defrost mode is The blower fan speed can be set to any fixed speed by selected, or by adjusting the blower control knob and adjusting the blower control knob. The fan will now setting the fan to any fixed speed.
Page 364
362 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In many temperature positions, the BI-LEVEL NOTE: While operating in the other modes, the system mode is designed to provide cooler air out of the panel will not automatically sense the presence of fog, mist or outlets and warmer air from the floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 363 Recirculation Control Summer Operation When outside air contains smoke, odors, or The engine cooling system in air conditioned vehicles high humidity, or if rapid cooling is desired, must be protected with a high-quality antifreeze coolant you may wish to recirculate interior air by to provide proper corrosion protection and to protect pressing the RECIRCULATION control button.
364 UNDERSTANDING YOUR INSTRUMENT PANEL Vacation/Storage Outside Air Intake Any time you store your vehicle or keep it out of service Make sure the air intake, located directly in front of the (i.e., vacation) for two weeks or more, run the air windshield, is free of obstructions such as leaves.
STARTING AND OPERATING 373 STARTING PROCEDURES Normal Starting Before starting your vehicle, adjust your seat, adjust both Normal starting of either a warm or cold engine is inside and outside mirrors, and fasten your seat belt. obtained without pumping or pressing the accelerator pedal.
374 STARTING AND OPERATING Tip Start Feature CAUTION! Do not press the accelerator. Turn the ignition switch briefly to the START position and release it. The starter To prevent damage to the starter, do not crank the motor will continue to run but will automatically disen- engine for more than 15 seconds at a time.
STARTING AND OPERATING 375 After Starting WARNING! (Continued) The idle speed is automatically controlled and will de- • If the vehicle has a discharged battery, booster crease as the engine warms up. cables may be used to obtain a start from a booster battery or the battery in another vehicle.
376 STARTING AND OPERATING It includes a removable cap that is secured by a tethered AUTOMATIC TRANSMISSION strap. It also has a c-clip that is used for storage when not CAUTION! in use for the winter months. During winter months, remove the heater cord wiring assembly from itself on Damage to the transmission may occur if the follow- the c-clip.
Page 379
STARTING AND OPERATING 377 WARNING! WARNING! (Continued) • Leaving children in a vehicle unattended is dan- • Unintended movement of a vehicle could injure gerous for a number of reasons. A child or others those in or near the vehicle. As with all vehicles, could be seriously or fatally injured.
378 STARTING AND OPERATING Key Ignition Park Interlock shift lever is mounted either on the right side of the This vehicle is equipped with a Key Ignition Park Inter- steering column (if equipped) or on the console (if lock which requires the shift lever to be placed in PARK equipped).
Page 381
STARTING AND OPERATING 379 Shifting from DRIVE to PARK or REVERSE should be PARK done only after the accelerator pedal is released and the This range supplements the parking brake by locking the vehicle is stopped. Be sure to keep your foot on the brake transmission.
Page 382
380 STARTING AND OPERATING WARNING! WARNING! (Continued) • It is dangerous to move the shift lever out of PARK • Never use the PARK position as a substitute for or NEUTRAL if the engine speed is higher than the parking brake. Always apply the parking idle speed.
Page 383
STARTING AND OPERATING 381 WARNING! (Continued) CAUTION! • Unintended movement of a vehicle could injure • Before moving the shift lever out of PARK, you those in or near the vehicle. As with all vehicles, must turn the ignition switch from the LOCK/OFF you should never exit a vehicle while the engine is position to the ON/RUN position, and also press running.
Page 384
382 STARTING AND OPERATING • Release the shift lever and make sure it is fully seated WARNING! in the PARK gate. Do not coast in NEUTRAL and never turn off the • Look at the shift lever position display and verify that ignition to coast down a hill.
Page 385
STARTING AND OPERATING 383 DRIVE torque converter clutch engagement. This is done to This range should be used for most city and highway prevent transmission damage due to overheating. driving. It provides the smoothest upshifts and down- If the transmission becomes extremely hot, the “Trans- shifts, and the best fuel economy.
Page 386
384 STARTING AND OPERATING Transmission Limp Home Mode 3. Turn the ignition switch to the LOCK/OFF position. Transmission function is monitored electronically for 4. Wait approximately 10 seconds. abnormal conditions. If a condition is detected that could result in transmission damage, Transmission Limp Home 5.
Page 387
STARTING AND OPERATING 385 Electronic Range Select (ERS) Operation The Electronic Range Select (ERS) shift control allows the driver to limit the highest available gear when the shift lever is in the DRIVE position. For example, if you shift the transmission into 3 (third gear), the transmission will never shift above third gear, but will shift down into second and first gear normally.
Page 388
386 STARTING AND OPERATING WARNING! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing an accident or personal injury. Screen Display Actual Gear(s) Allowed NOTE: To select the proper gear position for maximum deceleration (engine braking), tap the shift lever to the Console Shift Lever left (-) (console shift) or the ERS (-) switch down (column...
Page 389
STARTING AND OPERATING 387 Overdrive Operation HAUL mode. This will improve performance and reduce The automatic transmission includes an electronically the potential for transmission overheating or failure due controlled Overdrive (fourth gear). The transmission will to excessive shifting. When operating in TOW/HAUL automatically shift into the Overdrive gear if the follow- mode, the transmission will downshift into third gear.
388 STARTING AND OPERATING The “TOW/HAUL Indicator Light” will illuminate in the converter clutch is not engaged, it may seem as if the instrument cluster to indicate that TOW/HAUL mode transmission is not shifting into Overdrive when cold. has been activated. Pressing the switch a second time This is normal.
Page 391
STARTING AND OPERATING 389 The electronically-controlled transmission provides a Gear Ranges precise shift schedule. The transmission electronics are DO NOT race the engine when shifting from PARK or self-calibrating; therefore, the first few shifts on a new NEUTRAL into another gear range. vehicle may be somewhat abrupt.
Page 392
390 STARTING AND OPERATING WARNING! WARNING! (Continued) • It is dangerous to move the shift lever out of PARK • Never use the PARK position as a substitute for or NEUTRAL if the engine speed is higher than the parking brake. Always apply the parking idle speed.
Page 393
STARTING AND OPERATING 391 WARNING! (Continued) CAUTION! • Unintended movement of a vehicle could injure • Before moving the shift lever out of PARK, you those in and near the vehicle. As with all vehicles, must turn the ignition switch from the LOCK/OFF you should never exit a vehicle while the engine is position to the ON/RUN position, and also press running.
Page 394
392 STARTING AND OPERATING • Release the shift lever and make sure it is fully seated WARNING! in the PARK gate. Do not coast in NEUTRAL and never turn off the • Look at the shift lever position display and verify that ignition to coast down a hill.
Page 395
STARTING AND OPERATING 393 DRIVE If the transmission operating temperature exceeds normal This range should be used for most city and highway operating limits, the powertrain controller will modify the driving. It provides the smoothest upshifts and down- transmission shift schedule and expand the range of shifts, and the best fuel economy.
Page 396
394 STARTING AND OPERATING During cold temperatures, transmission operation may PARK, REVERSE, and NEUTRAL will continue to oper- be modified depending on engine and transmission ate. Limp Home Mode allows the vehicle to be driven to temperature as well as vehicle speed. This feature im- an authorized dealer for service without damaging the proves warm up time of the engine and transmission to transmission.
Page 397
STARTING AND OPERATING 395 NOTE: Even if the transmission can be reset, we recom- Use of ERS (or TOW/HAUL mode) also enables an mend that you visit your authorized dealer at your additional underdrive gear which is not normally used earliest possible convenience.
Page 398
396 STARTING AND OPERATING shift the transmission down to ERS 3 (the added under- drive gear). Once in ERS mode, tapping ERS (-) or (+) will change the top available gear. Console Shift Lever To exit ERS mode, simply press and hold the shift lever to the right (+) (console shift) or the ERS (+) switch (column shift) until “D”...
Page 399
STARTING AND OPERATING 397 Overdrive Operation WARNING! The automatic transmission includes an electronically controlled Overdrive (fourth and fifth gears). The trans- Do not downshift for additional engine braking on a mission will automatically shift into the Overdrive gear if slippery surface. The drive wheels could lose their the following conditions are present: grip and the vehicle could skid, causing and accident or personal injury.
Page 400
398 STARTING AND OPERATING HAUL mode. This will improve performance and reduce The “TOW/HAUL Indicator Light” will illuminate in the the potential for transmission overheating or failure due instrument cluster to indicate that TOW/HAUL mode to excessive shifting. When operating in TOW/HAUL has been activated.
STARTING AND OPERATING 399 warm [usually after 1 to 3 miles (1.6 to 4.8 km) of Six–Speed Automatic Transmission (5.7L Engine) driving]. Because top gear is disabled, and the engine — 2500 Models Only speed is higher when the torque converter clutch is not The shift lever position display (located in the instrument engaged, it may seem as if the transmission is not panel cluster) indicates the transmission gear range.
Page 402
400 STARTING AND OPERATING Shifting from DRIVE to PARK or REVERSE should be PARK done only after the accelerator pedal is released and the This range supplements the parking brake by locking the vehicle is stopped. Be sure to keep your foot on the brake transmission.
Page 403
STARTING AND OPERATING 401 WARNING! WARNING! (Continued) • It is dangerous to move the shift lever out of PARK • Never use the PARK position as a substitute for or NEUTRAL if the engine speed is higher than the parking brake. Always apply the parking idle speed.
Page 404
402 STARTING AND OPERATING WARNING! (Continued) CAUTION! • Unintended movement of a vehicle could injure • Before moving the shift lever out of PARK, you those in and near the vehicle. As with all vehicles, must turn the ignition switch from the LOCK/OFF you should never exit a vehicle while the engine is position to the ON/RUN position, and also press running.
Page 405
STARTING AND OPERATING 403 • Look at the shift lever position display and verify that WARNING! it indicates the PARK position. Do not coast in NEUTRAL and never turn off the • With brake pedal released, verify that the shift lever ignition to coast down a hill.
Page 406
404 STARTING AND OPERATING DRIVE If the transmission operating temperature exceeds normal This range should be used for most city and highway operating limits, the powertrain controller will modify the driving. It provides the smoothest upshifts and down- transmission shift schedule and expand the range of shifts, and the best fuel economy.
Page 407
STARTING AND OPERATING 405 During cold temperatures, transmission operation may to operate. Limp Home Mode allows the vehicle to be be modified depending on engine and transmission driven to an authorized dealer for service without dam- temperature as well as vehicle speed. This feature im- aging the transmission.
Page 408
406 STARTING AND OPERATING NOTE: Even if the transmission can be reset, we recom- switch will activate ERS mode, display the current gear in mend that you visit your authorized dealer at your the instrument cluster, and maintain that gear as the top earliest possible convenience.
Page 409
STARTING AND OPERATING 407 To exit ERS mode, simply press and hold the ERS (+) Overdrive Operation switch until “D” is once again displayed in the shift lever The automatic transmission includes an electronically position indicator in the instrument cluster. controlled Overdrive (fifth and sixth gears).
Page 410
408 STARTING AND OPERATING HAUL mode. This will improve performance and reduce The “TOW/HAUL Indicator Light” will illuminate in the the potential for transmission overheating or failure due instrument cluster to indicate that TOW/HAUL mode to excessive shifting. When operating in TOW/HAUL has been activated.
STARTING AND OPERATING 409 transmission fluid and engine coolant are warm [usu- FOUR-WHEEL DRIVE OPERATION — IF ally after 1 to 3 miles (1.6 to 4.8 km) of driving]. EQUIPPED Because sixth gear is disabled, and engine speed is Four-wheel drive trucks are equipped with either a higher when the torque converter clutch is not en- manually shifted transfer case or an electronically shifted gaged, it may seem as if the transmission is not...
Page 412
410 STARTING AND OPERATING When additional traction is required, the 4H and 4L When operating your vehicle in 4L, the engine speed is positions can be used to lock the front and rear drive- approximately three times that of the 2H or 4H positions shafts together and force the front and rear wheels to at a given road speed.
Page 413
STARTING AND OPERATING 411 NOTE: Delayed shifts out of four-wheel drive may be For additional information on the appropriate use of each experienced due to uneven tire wear, low or uneven tire transfer case mode position, see the information below: pressures, excessive vehicle loading, or cold tempera- tures.
412 STARTING AND OPERATING 2H Or 4H ⇔ 4L Four-Wheel Drive Low Range - This range locks the front With the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift and rear driveshafts together forcing the front and rear the transmission into NEUTRAL.
STARTING AND OPERATING 413 method is with the vehicle rolling 2 to 3 mph (3 to 5 km/h). Avoid attempting to engage or disengage 4L with the vehicle moving faster than 2 to 3 mph (3 to 5 km/h). • Do not attempt to shift into or from 4L while the transmission is in gear.
Page 416
414 STARTING AND OPERATING • Neutral (NEUTRAL) NOTE: The transfer case NEUTRAL position is selected by pressing the recessed button located on the lower left This electronically shifted transfer case is designed to be hand corner of the 4WD Control Switch. The transfer case driven in the two-wheel drive position (2WD) for normal NEUTRAL position is to be used for recreational towing street and highway conditions on dry, hard surfaced...
Page 417
STARTING AND OPERATING 415 3. When the shift is complete, the indicator light for the The “SVC 4WD Warning Light” monitors the electronic selected position will stop flashing and remain ON. shift four-wheel drive system. If this light remains on after engine start up or illuminates during driving, it If One Or More Shift Conditions Are Not Met: means that the four-wheel drive system is not function-...
Page 418
416 STARTING AND OPERATING When operating your vehicle in 4WD LOW, the engine WARNING! speed is approximately three times that of the 2WD or 4WD LOCK positions at a given road speed. Take care You or others could be injured if you leave the not to overspeed the engine and do not exceed 25 mph vehicle unattended with the transfer case in the (40 km/h).
STARTING AND OPERATING 417 4WD LOCK Shifting Procedure Four-Wheel Drive Lock Range - This range locks the front NOTE: and rear driveshafts together forcing the front and rear • If any of the requirements to select a new transfer case wheels to rotate at the same speed.
Page 420
418 STARTING AND OPERATING 2WD⇔ 4WD LOCK 2WD Or 4WD LOCK⇔ 4WD LOW Rotate the 4WD control switch to the desired position. NOTE: When shifting into or out of 4WD LOW some Shifts between 2WD and 4WD LOCK can be done with gear noise may be heard.
Page 421
STARTING AND OPERATING 419 Alternate Procedure NOTE: • If Steps 1 or 2 of either the Preferred or Alternate 1. Bring the vehicle to a complete stop. Procedure are not satisfied prior to attempting the 2. With the ignition switch in the ON position and the shift, then the desired position indicator light will flash engine either OFF or running, shift the transmission into continuously while the original position indicator light...
420 STARTING AND OPERATING Electronically Shifted Transfer Case This electronically shifted transfer case provides five (Five-Position Switch) – If Equipped mode positions: This is an electronic shift transfer case and is operated by • Two-wheel drive high range (2WD) the 4WD Control Switch (Transfer Case Switch), which is •...
Page 423
STARTING AND OPERATING 421 drive will be automatically engaged when the vehicle left hand corner of the 4WD Control Switch. The transfer senses a loss of traction. Because the front axle is en- case NEUTRAL position is to be used for recreational gaged, this mode will result in lower fuel economy than towing only.
Page 424
422 STARTING AND OPERATING If One Or More Shift Conditions Are Not Met: The “SVC 4WD Warning Light” monitors the electronic shift four-wheel drive system. If this light remains on 1. The indicator light for the current position will remain after engine start up or illuminates during driving, it means that the four-wheel drive system is not function- 2.
Page 425
STARTING AND OPERATING 423 When operating your vehicle in 4WD LOW, the engine WARNING! speed is approximately three times that of the 2WD, 4WD AUTO or 4WD LOCK positions at a given road speed. You or others could be injured if you leave the Take care not to overspeed the engine and do not exceed vehicle unattended with the transfer case in the 25 mph (40 km/h).
424 STARTING AND OPERATING 4WD AUTO Four-Wheel Drive Auto Range - This range sends power Neutral - This range disengages both the front and rear to the rear wheels. The four–wheel drive system will be driveshafts from the powertrain. To be used for flat automatically engaged when the vehicle senses a loss of towing behind another vehicle.
Page 427
STARTING AND OPERATING 425 • If all the requirements to select a new transfer case 2WD Or 4WD AUTO Or 4WD LOCK ⇔ 4WD position have been met, the current position indicator light will turn OFF, the selected position indicator light NOTE: When shifting into or out of 4WD LOW some will flash until the transfer case completes the shift.
426 STARTING AND OPERATING • The ignition switch must be in the ON position for a Alternate Procedure shift to take place and for the position indicator lights 1. Bring the vehicle to complete stop. to be operable. If the ignition switch is not in the ON 2.
Page 429
STARTING AND OPERATING 427 position, the rear axle is locked. In the FRONT/REAR CAUTION! LOCK position, the front and rear axles are locked. • Do not lock the front or rear axle on hard surfaced NOTE: Even when the axles are in the AXLE UNLOCK roads.
Page 430
428 STARTING AND OPERATING NOTE: Left to right wheel speed difference may be NOTE: The rear axle must be locked before the front necessary to allow the axle to fully lock. If the indicator axle will lock. light is flashing after placing the switch in the REAR To unlock the front axle;...
STARTING AND OPERATING 429 STABILIZER/SWAY BAR SYSTEM — POWER WAGON ONLY Your vehicle is equipped with an electronic disconnecting stabilizer/sway bar. This system allows greater front suspension travel in off-road situations. Due to the use of taller springs, this vehicle has an increased ride height of approximately 1.9 in (48.3 mm) in the front and 1.5 in (38.1 mm) in the rear.
Page 432
430 STARTING AND OPERATING To disconnect the stabilizer/sway bar, shift to either 4HI WARNING! or 4LO as shown in “Four Wheel Drive Operation” and press the top of the stabilizer/sway bar button to obtain Do not disconnect the stabilizer bar and drive on the Off-Road position.
STARTING AND OPERATING 431 venture out, you should contact your local governmental WARNING! agency to determine the designated off-road vehicle (ORV) trails or recreation areas. You should always tread If the stabilizer/sway bar will not return to On-Road lightly and only use established roads, trails or ORV mode, vehicle stability is greatly reduced.
Page 434
432 STARTING AND OPERATING Ramp Travel Index (RTI) CAUTION! The ramp travel index is the distance, in inches, that you can drive your vehicle with one wheel on a 20-degree The door sill height is 25 inches. Water may intrude ramp without lifting any other wheel off the ground.
Page 435
STARTING AND OPERATING 433 your vehicle’s steering, handling and traction. Control- WARNING! ling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel Always wear your seat belt and firmly tie down and maintain a good driving posture.
434 STARTING AND OPERATING Driving In Snow, Mud And Sand CAUTION! There is a drastic reduction in traction when driving in snow, mud or sand. The vehicle will be less responsive to On icy or slippery roads, do not downshift at high steering, acceleration and braking inputs.
STARTING AND OPERATING 435 • Sand – Soft sand is very difficult to travel through CAUTION! with full tire pressure. When crossing soft sandy spots in a trail maintain your vehicle’s momentum and do Reduced tire pressures may cause tire unseating and not stop.
Page 438
436 STARTING AND OPERATING forward until it makes contact with the object. Apply the Crossing Large Rocks throttle lightly while holding a light brake pressure and When approaching large rocks, choose a path which ease the vehicle up and over the object. ensures you drive over the largest with your tires.
Page 439
STARTING AND OPERATING 437 independently. You need to use caution when crossing accelerator to avoid spinning the log out from under your large obstacles with steep sides. Do not attempt to cross tires. Then ease the vehicle off the log using your brakes. any large obstacle with steep sides at an angle great CAUTION! enough to put the vehicle at risk of a rollover.
438 STARTING AND OPERATING the vehicle if something goes wrong? If everything CAUTION! looks good and you feel confident, then change trans- mission into a lower gear, shift the transfer case into 4L Winching or rocking the vehicle off hard objects (Low) and proceed with caution.
Page 441
STARTING AND OPERATING 439 fresh bite into the surface and will usually provide ability to proceed then make sure you are in 4L (Low enough traction to complete the climb. If you do not Range) with the transmission in first gear (manually make it to the top, place the vehicle in REVERSE and select first gear on automatic transmissions) and pro- back straight down the grade using engine resistance...
440 STARTING AND OPERATING sure the surface has good traction with firm and stable WARNING! soils. If possible transverse the incline at an angle heading slightly up or down. If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never WARNING! attempt to turn around.
Page 443
STARTING AND OPERATING 441 your vehicle’s abilities and be able to recover it if CAUTION! something goes wrong. You should never stop or shut a vehicle off when crossing deep water unless you ingested Water ingestion into the axles, transmission, transfer water into the engine air intake.
Page 444
442 STARTING AND OPERATING crossing is the water depth, current and bottom con- CAUTION! ditions. On soft bottoms the vehicle will sink in, effectively increasing the water level on the vehicle. Be Muddy waters can reduce the cooling system effec- sure to consider this when determining the depth and tiveness by depositing debris onto the radiator.
STARTING AND OPERATING 443 downstream out of control if the water is deep enough form to the ground contour. Different terrain, tires, and to push on the large surface area of the vehicle’s body. vehicles require different tire pressure. Hard surfaces like Before you proceed determine the speed of the current, rock and heavier vehicles require higher pressures than the water’s depth, approach angle, bottom condition...
444 STARTING AND OPERATING Vehicle Recovery ample room, an additional vehicle and there is low risk of If you drive off-road, you may encounter a situation vehicle impingement on the surroundings, then using a where you will need to recover your vehicle. Vehicle tow strap to the vehicle tow hooks would be fast and recovery should always be given consideration before easy.
Page 447
STARTING AND OPERATING 445 • Rock Cycling Your Vehicle – Rock cycling your ve- CAUTION! hicle is one of the easiest, fastest and most commonly used methods. This simply involves shifting your Damage can occur when spinning your tires at an vehicle from DRIVE to REVERSE, while applying excessive high speed.
Page 448
446 STARTING AND OPERATING two tow straps together using a 1 ⁄ inch hard wood WARNING! dowel. This will keep the straps from becoming knot- ted and is safer than using a clevis pin if the strap Never use tow straps with end hooks or link two breaks.
Page 449
STARTING AND OPERATING 447 out of the situation in a slow controlled manner. This the vehicle in first gear and apply a very light throttle control works well for avoiding further vehicle dam- as you power the winch in. Be careful not to allow age.
448 STARTING AND OPERATING • Check for accumulations of plants or brush. These After Driving Off-Road Off-road operation puts more stress on your vehicle than things could be a fire hazard. They might hide damage does most on-road driving. After going off-road, it is to fuel lines, brake hoses, axle pinion seals, and always a good idea to check for damage.
STARTING AND OPERATING 449 • If you experience unusual vibration after driving in will supply maximum traction. When starting with only mud, slush or similar conditions, check the wheels for one rear wheel on an excessively slippery surface, slight impacted material. Impacted material can cause a momentary application of the parking brake may be wheel imbalance and freeing the wheels of it will necessary to gain maximum traction.
450 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES Traction When driving on wet or slushy roads, it is possible for a Acceleration wedge of water to build up between the tire and road Rapid acceleration on snow covered, wet, or other slip- surface.
STARTING AND OPERATING 451 DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Caution safety and prevent damage to your vehicle.
Page 454
452 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Driving through standing water may cause dam- • Driving through standing water limits your vehi- age to your vehicle’s drivetrain components. Al- cle’s traction capabilities. Do not exceed 5 mph ways inspect your vehicle’s fluids (i.e., engine oil, (8 km/h) when driving through standing water.
STARTING AND OPERATING 453 OFF-ROAD DRIVING TIPS always a good idea to check for damage. That way you Care should be taken when attempting to climb steep can get any problems taken care of right away and have hills or driving diagonally across a hill or slope. If natural your vehicle ready when you need it.
454 STARTING AND OPERATING • After extended operation in mud, sand, water, or WINCH USAGE (POWER WAGON ONLY) — IF similar dirty conditions, have the radiator, fan, brake EQUIPPED rotors, wheels, brake linings, and axle yokes inspected Things To Know Before Using Your Winch and cleaned as soon as possible.
Page 457
STARTING AND OPERATING 455 2. Attach the hook to a suitable anchor point. Low Voltage Interrupt Your winch is equipped with a device that will interrupt CAUTION! winch function if the vehicle charging system voltage drops to a low level. The winch will not power-in or out Be certain the anchor will withstand the load re- for 30 seconds if this device is tripped.
456 STARTING AND OPERATING Understanding The Features Of Your Winch Winch Components...
Page 459
STARTING AND OPERATING 457 1. Motor: The winch motor is powered by the vehicle 6. Clutch Lever: The clutch lever allows the winch drum charging system and features a thermal protection switch to be disconnected from the winch motor to allow the that automatically stops motor function in the power-in wire rope to be pulled from the winch by hand.
458 STARTING AND OPERATING Winch Accessories Snatch/Block Pulley: Used properly, the multi-purpose The following accessories are necessary to attach the snatch block allows you to (1) winch to anchors, change direction of pull, and for safe increase the winch’s pulling winching.
STARTING AND OPERATING 459 Clevis/D-Shackles: Operating Your Winch D-Shackle is a safe means of WARNING! connecting the looped ends of cables, straps and snatch Failure to observe any of these warnings regarding blocks. The shackle’s pin is proper winch usage may result in severe injury. threaded to allow easy re- •...
Page 462
460 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Always stand clear of wire rope and load and keep • Always disconnect the remote control when not in others away during winching. use. • Always keep hands and clothing clear of the wire •...
Page 463
STARTING AND OPERATING 461 2. Always take your time when using a winch. Vehicle Recovery Using The Winch 3. Use the right equipment for the situation. CAUTION! 4. Always wear leather gloves and do not allow the wire • Always Know Your Winch: Take the time to fully rope to slip through your hands when handling the rope.
Page 464
462 STARTING AND OPERATING CAUTION! (Continued) • Always keep remote control lead clear of the drum, wire rope and rigging. • Inspect for cracks, pinches, frayed wires, or loose connections. Replace if damaged. • Be careful not to pull the Winch Cable Collar through the rollers.
Page 465
STARTING AND OPERATING 463 3. Disengage the clutch to allow free spooling of the 4. Free the winch hook and attach the hook strap. Free winch drum, rotate the clutch lever on the winch to the winch hook from its anchor point. Attach the hook disengage.
Page 466
464 STARTING AND OPERATING 5. Pull the wire to the anchor point. Pull out enough wire 6. Secure to the anchor point. Once you have established rope to reach your anchor point. Be sure to keep a certain your anchor point, secure the tree-trunk protector or amount of tension on the wire as it can become twisted choker-chain around the object.
Page 467
STARTING AND OPERATING 465 7. Attach the Clevis/D-shackle and Tree Trunk Protector. CAUTION! Attach the shackle to the two ends of the strap or chain and through the hook loop, being careful not to over Always be certain the anchor you select will with- tighten (tighten and back-off 1/2 turn).
Page 468
466 STARTING AND OPERATING NOTE: Always ensure the clutch is fully engaged or disengaged. 9. Connect the remote control to the winch control box, located behind the front bumper. Be careful not to let the remote control cord dangle in front of the winch. If you choose to control the winch from inside your vehicle, always pass the remote through a window to avoid pinching the cord in the door.
Page 469
STARTING AND OPERATING 467 12. Check wire rope. The wire rope should be neatly wound around the spooling drum. Improper winding can cause damage to the wire rope. 11. Check your anchor. Make sure all connections are secured and free of debris before continuing with the winching procedure.
Page 470
468 STARTING AND OPERATING 13. In certain situations you the vehicle and never near the wire rope or snatch may decide to throw a heavy block. Your situation may have other no people zones. blanket or similar object over the wire rope. A heavy blan- ket can absorb energy should the wire rope break.
Page 471
STARTING AND OPERATING 469 For additional assistance, the winched vehicle can be NOTE: • Avoid overheating the winch motor. For extended slowly driven while being pulled by the winch. Continue pulling until the vehicle is on stable ground. If you are winching, stop at reasonable intervals to allow the able to drive the vehicle, the winching operation is winch motor to cool down.
Page 472
470 STARTING AND OPERATING section of the rope and reposition it to the opposite end of the drum, which will free up space for continued winching. 16. Secure vehicle. Once recovery of the vehicle’s is complete, be sure to secure the vehicle’s brakes and put the transmission in PARK.
Page 473
STARTING AND OPERATING 471 Arrange the wire rope so it will not kink or tangle when spooled. Be sure any wire rope already on the spooling drum is wound tightly and evenly layered. Tighten and straighten the layer if necessary. Keep the wire rope under light tension and spool the wire rope back and onto the winch drum in even layers.
472 STARTING AND OPERATING Rigging Techniques How To Change The Pulling Direction Various winching situations will require application of other winching techniques. These could range from too little distance to achieve maximum pull using straight line rigging, simply increasing pulling power, or main- taining a straight-line pulling situation.
Page 475
STARTING AND OPERATING 473 All winching operations should have a straight line from Double Line the winch to the object being pulled. This minimizes the wire rope collecting on one side of the drum affecting pulling efficiency and damaging wire rope. A snatch block, secured to a point directly in front of the vehicle will enable you to change your pulling direction while still allowing the wire rope to be at 90°...
474 STARTING AND OPERATING vehicle’s frame/tow hook and run the wire rope through NOTE: • Increased noise levels at the end of the steering wheel a snatch block. Disengage the clutch and, using the snatch block, pull out enough wire to reach your anchor travel are considered normal and do not indicate that point.
STARTING AND OPERATING 475 CAUTION! CAUTION! Prolonged operation of the steering system at the end Do not use chemical flushes in your power steering of the steering wheel travel will increase the steering system as the chemicals can damage your power fluid temperature and it should be avoided when steering components.
476 STARTING AND OPERATING MULTI-DISPLACEMENT SYSTEM (MDS) (IF EQUIPPED) — 5.7L ENGINE ONLY This feature offers improved fuel economy by shutting off four of the engine’s eight cylinders during light load and cruise conditions. The system is automatic with no driver inputs or additional driving skills required.
Page 479
STARTING AND OPERATING 477 NOTE: WARNING! • When the parking brake is applied and the transmis- • Never use the PARK position as a substitute for sion is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound the parking brake.
478 STARTING AND OPERATING If either the front or rear hydraulic system loses normal WARNING! (Continued) braking capability, the remaining system will still func- • Always fully apply the parking brake when leav- tion with some loss of overall braking effectiveness. This ing your vehicle or it may roll and cause damage or will be evident by increased pedal travel during applica- injury.
STARTING AND OPERATING 479 ELECTRONIC BRAKE CONTROL SYSTEM WARNING! Your vehicle is equipped with an advanced electronic • ABS cannot prevent the natural laws of physics brake control system that includes Anti-Lock Brake Sys- tem (ABS), Traction Control System (TCS), Brake Assist from acting on the vehicle, nor can it increase System (BAS), Hill Start Assist (HSA), Electronic Stability braking or steering efficiency beyond that af-...
480 STARTING AND OPERATING Traction Control System (TCS) – If Equipped Brake Assist System (BAS) – If Equipped The TCS monitors the amount of wheel spin of each of The BAS is designed to optimize the vehicle’s braking the driven wheels. If wheel spin is detected, brake capability during emergency braking maneuvers.
STARTING AND OPERATING 481 level of brake pressure the driver inputs for a short WARNING! duration once the driver takes his foot off of the brake • The BAS cannot prevent the natural laws of phys- pedal. If the driver does not apply the throttle during this short duration, the system will release brake pressure ics from acting on the vehicle, nor can it increase and the vehicle will roll down the incline.
Page 484
482 STARTING AND OPERATING • Gear selection matches vehicle uphill direction (i.e., The system will work in REVERSE and all forward gears, vehicle facing uphill is in forward gear; vehicle back- and will not activate if the vehicle is placed in ing uphill is in REVERSE gear).
Page 485
STARTING AND OPERATING 483 WARNING! WARNING! (Continued) • HSA is not a parking brake. If you stop the vehicle • If you use a trailer brake controller with your on a hill without putting the transmission in trailer, your trailer brakes may be activated and PARK or using the parking brake, it will roll down deactivated with the brake switch.
484 STARTING AND OPERATING 3. With the engine running and the brake applied, rotate EVIC Equipped Vehicles the steering wheel 180° counterclockwise from center. HSA is a Customer Programmable Feature on a EVIC equipped vehicle. If you wish to turn off the HSA feature, 4.
Page 487
STARTING AND OPERATING 485 the intended path, ESC applies the brake of the appro- this mode. This mode should be used for almost all priate wheel to assist in counteracting the oversteer or driving situations. ESC should only be turned to “Partial understeer condition.
Page 488
486 STARTING AND OPERATING ESC Partial Off mode is overcome, turn ESC back on by momentarily This mode is entered by momentarily pressing the “ESC pressing the “ESC Off” switch. This may be done while Off” switch. When in Partial Off mode, the TCS portion the vehicle is in motion.
Page 489
STARTING AND OPERATING 487 holding the “ESC Off” switch for five seconds when the with off-road driving but ESC function returns to provide vehicle is stopped and the engine is running. After five the stability feature at speeds above 40 mph (64 km/h). seconds, the “ESP Off Indicator Light”...
488 STARTING AND OPERATING ESC Activation/Malfunction Indicator Light And Malfunction Indicator Light” begins to flash during ac- ESC OFF Indicator Light celeration, ease up on the accelerator and apply as little The “ESC Activation/Malfunction Indicator throttle as possible. Be sure to adapt your speed and Light”...
STARTING AND OPERATING 489 Trailer Sway Control (TSC) – If Equipped TSC is only active in the default “ESC On” mode. TSC The TSC system uses sensors in the vehicle to recognize can be disabled by pressing the “ESC Off” switch and an excessively swaying trailer and will take the appro- entering “ESC Partial Off”...
490 STARTING AND OPERATING TIRE SAFETY INFORMATION NOTE: • P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 493
STARTING AND OPERATING 491 • High flotation tire sizing is based on U.S. design compact spare tires have the letter “T” or “S” molded into the sidewall preceding the size designation. Ex- standards and it begins with the tire diameter molded ample: T145/80D18 103M.
Page 494
492 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
STARTING AND OPERATING 493 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
494 STARTING AND OPERATING Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the Cold Tire Inflation Pressure vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
STARTING AND OPERATING 495 Tire Loading And Tire Pressure Tire And Loading Information Placard Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
Page 498
496 STARTING AND OPERATING Loading To determine the maximum loading conditions of your The vehicle maximum load on the tire must not exceed vehicle, locate the statement “The combined weight of the load carrying capacity of the tire on your vehicle. You occupants and cargo should never exceed XXX lbs or will not exceed the tire’s load carrying capacity if you XXX kg”...
Page 499
STARTING AND OPERATING 497 3. Subtract the combined weight of the driver and pas- NOTE: • The following table shows examples on how to calcu- sengers from XXX lbs or XXX kg. late total load, cargo/luggage, and towing capacities 4. The resulting figure equals the available amount of of your vehicle with varying seating configurations cargo and luggage load capacity.
STARTING AND OPERATING 499 Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
500 STARTING AND OPERATING Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the • Unequal tire pressures from one side of the ve- driver’s side “B” Pillar or rear edge of the driver’s side hicle to the other can cause the vehicle to drift to door.
Page 503
STARTING AND OPERATING 501 Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, al- the Winter.
502 STARTING AND OPERATING Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
STARTING AND OPERATING 503 Spare Tire Matching Original Equipped Tire And CAUTION! Wheel – If Equipped Your vehicle may be equivalent with a spare tire and Because of the reduced ground clearance, do not take wheel in look and function as the original equipment tire your vehicle through an automatic car wash with a and wheel found on the front or rear axle of your vehicle.
504 STARTING AND OPERATING Since this tire has limited tread life the original equip- Full Size Spare – If Equipped ment tire should be repaired (or replaced) and reinstalled The full size spare is for temporary emergency use only. on your vehicle at the first opportunity. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not.
STARTING AND OPERATING 505 your original equipment tire, replace (or repair) the Tire Spinning original equipment tire and reinstall on the vehicle at the When stuck in mud, sand, snow, or ice conditions, do not first opportunity. spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without WARNING! stopping when you are stuck.
506 STARTING AND OPERATING Tread Wear Indicators These indicators are molded into the bottom of the tread Tread wear indicators are in the original equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes 1/16 in (2 mm).
STARTING AND OPERATING 507 Keep dismounted tires in a cool, dry place with as little It is recommended to replace the two front tires or two exposure to light as possible. Protect tires from contact rear tires as a pair. Replacing just one tire can seriously with oil, grease, and gasoline.
508 STARTING AND OPERATING WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
STARTING AND OPERATING 509 TIRE CHAINS CAUTION! (Continued) Use “Class S” chains, or other traction aids that meet SAE • Because of limited chain clearance between tires Type “S” specifications. and other suspension components, it is important Use “Class U” chains on 2500/3500 model trucks, or that only chains in good condition are used.
Page 512
510 STARTING AND OPERATING • On 4x4 2500 model trucks, the use of class “U” snow CAUTION! (Continued) chains is permitted on the rear wheels only of trucks • Observe the tire chain manufacturer’s instructions equipped with LT245/70R17, LT265/70R17, or LT285/ on method of installation, operating speed, and 70R17 tires.
STARTING AND OPERATING 511 If you need snow tires, select tires equivalent in size and CAUTION! type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the Do not use tire chains on the front wheels of any safety and handling of your vehicle.
512 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS The suggested rotation method is the “forward cross” Tires on the front and rear axles of vehicles operate at shown in the following diagram. This rotation pattern different loads and perform different steering, driving, does not apply to some directional tires that must not be and braking functions.
STARTING AND OPERATING 513 Directional Tires – If Equipped Dual Rear Wheels – If Equipped For the R/T package with 22” tires & wheels, tire rotation must be performed with consideration of the tire rotation direction. The recommended rotation pattern for direc- tional tires is shown below.
514 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) CAUTION! The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recom- 3500 Dual Rear Tires have only one approved direc- mended cold placard pressure. tion of rotation.
Page 517
STARTING AND OPERATING 515 The TPMS will warn the driver of a low tire pressure if For example, your vehicle may have a recommended the tire pressure falls below the low-pressure warning cold (parked for more than three hours) placard pressure limit for any reason, including low temperature effects of 30 psi (207 kPa).
Page 518
516 STARTING AND OPERATING NOTE: CAUTION! • The TPMS is not intended to replace normal tire care • The TPMS has been optimized for the original and maintenance or to provide warning of a tire failure or condition. equipment tires and wheels. TPMS pressures and warning have been established for the tire size •...
STARTING AND OPERATING 517 • Seasonal temperature changes will affect tire pressure, The matching full size spare wheel and tire assembly (if and the TPMS will monitor the actual tire pressure in equipped) has a TPM sensor. The matching full size spare the tire.
Page 520
518 STARTING AND OPERATING turn off. The vehicle may need to be driven for up to 3. Accumulation of snow or ice around the wheels or 20 minutes above 15 mph (24 km/h) in order for the wheel housings. TPMS to receive this information. 4.
STARTING AND OPERATING 519 3. Driving the vehicle for up to 20 minutes above 15 mph The TPMS consists of the following components: (24 km/h) will turn off the TPM Telltale Light and “LOW • Receiver module, TIRE PRESSURE” text message, as long as no tire pres- •...
Page 522
520 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The TPM Telltale Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the EVIC will display a “LOW TIRE PRESSURE”...
Page 523
STARTING AND OPERATING 521 turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. Service TPMS Warning If a system fault is detected, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid.
Page 524
522 STARTING AND OPERATING If the ignition switch is cycled, this sequence will repeat, 4. Using tire chains on the vehicle. providing the system fault still exists. If the system fault 5. Using wheels/tires not equipped with TPM sensors. no longer exists, the TPM Telltale Light will no longer flash, and the “SERVICE TPM SYSTEM”...
STARTING AND OPERATING 523 Vehicles With Full Size Spare Tire Pressure Monitor System (TPMS) Tire Light Load Inflation Switch Description (2500 Models) – 1. The matching full size spare wheel and tire assembly If Equipped has a TPM sensor that can be monitored by the TPMS. WARNING! 2.
Page 526
524 STARTING AND OPERATING The TPMS tire light load inflation switch will allow the driver to switch between the max load inflation pressure (cold) low pressure warning threshold and the light load inflation pressure (cold) low pressure warning threshold depending on the vehicle’s load condition. The Tire and Loading Information label defines the recommended front and rear cold tire inflation pressures for the vehicle when operating in the Max Load condition.
Page 527
STARTING AND OPERATING 525 Tire Light Load Inflation Switch Operation – If Equipped • This vehicle may have different recommended tire pressure values between the front and rear tires as shown in both the Tire Loading Information Label and the Supplemental Tire Pressure Information Label. It is also equipped to be driven with tire pressures appro- priate to either a Light Load condition or the vehicle Max Load condition.
Page 528
526 STARTING AND OPERATING Tire Pressure Information label. The Supplemental Tire Supplemental Tire Pressure Information label located on Pressure Information label is located on the rear face of the rear face of the driver door. Using an accurate tire the driver door opening. Use an accurate tire gauge to pressure gauge, re-check the tire pressures for the light check the tire pressures when lowering all four tire load inflation pressure (cold) value.
STARTING AND OPERATING 527 To switch back to the max load inflation pressure (cold) General Information low pressure warning threshold, press the tire light load This device complies with Part 15 of the FCC rules and inflation switch. It is not necessary to first fill the tires to RSS 210 of Industry Canada.
528 STARTING AND OPERATING FUEL REQUIREMENTS optimum performance. The use of premium gasoline is not recommended, as it will not provide any benefit over 3.7L and 4.7L Engine regular gasoline in these engines. These engines are designed to meet all emissions regulations and provide excel- Light spark knock at low engine speeds is not harmful to lent fuel economy and performance when...
STARTING AND OPERATING 529 Reformulated Gasoline CAUTION! Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” DO NOT use gasoline containing Methanol or gaso- Reformulated gasolines contain oxygenates and are spe- line containing more than 10% Ethanol. Use of these cifically blended to reduce vehicle emissions and im- blends may result in starting and driveability prob- prove air quality.
530 STARTING AND OPERATING If a Non-FFV vehicle is inadvertently fueled with E-85 More extensive repairs will be required for prolonged fuel, the engine will have some or all of these symptoms: exposure to E-85 fuel. • operate in a lean mode MMT In Gasoline MMT is a manganese containing metallic additive that is •...
STARTING AND OPERATING 531 Materials Added To Fuel CAUTION! (Continued) All gasoline sold in the United States is required to • An out-of-tune engine or certain fuel or ignition contain effective detergent additives. Use of additional malfunctions can cause the catalytic converter to detergents or other additives is not needed under normal overheat.
532 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper WARNING! maintenance. Have the exhaust system inspected Carbon monoxide (CO) in exhaust gases is deadly. every time the vehicle is raised. Have any abnor- Follow the precautions below to prevent carbon mal conditions repaired promptly.
STARTING AND OPERATING 533 E-85 Fuel Cap E-85 Badge Ethanol Fuel (E-85) CAUTION! E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Only vehicles with the E-85 fuel filler door label can operate on E-85.
534 STARTING AND OPERATING • you do not add less than 5 gallons (19 Liters) when WARNING! refueling Ethanol vapors are extremely flammable and could • you operate the vehicle immediately after refueling for cause serious personal injury. Never have any smok- a period of at least 5 minutes ing materials lit in or near the vehicle when remov- Observing these precautions will avoid possible hard...
STARTING AND OPERATING 535 Selection Of Engine Oil For Flexible Fuel Vehicles NOTE: Use of the engine block heater (if equipped) is (E-85) And Gasoline Vehicles beneficial for E-85 startability when the ambient tempera- FFV vehicles operated on E-85 require specially formu- ture is less than 32°F (0°C).
536 STARTING AND OPERATING CAUTION! Replacing fuel system components with non-ethanol compatible components can damage your vehicle. Maintenance CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability. Fuel Filler Cap ADDING FUEL NOTE: When removing the fuel filler cap, lay the cap...
Page 539
STARTING AND OPERATING 537 CAUTION! WARNING! • Damage to the fuel system or emissions control • Never have any smoking materials lit in or near system could result from using an improper fuel the vehicle when the gas cap is removed or the tank filler tube cap (gas cap).
538 STARTING AND OPERATING • When the fuel nozzle “clicks” or shuts off, the fuel This label contains the month and year of manufacture, tank is full. Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Loose Fuel Filler Cap Message Number (VIN).
Page 541
STARTING AND OPERATING 539 Gross Axle Weight Rating (GAWR) Inflation Pressure The GAWR is the maximum permissible load on the front This is the cold tire inflation pressure for your vehicle for and rear axles. The load must be distributed in the cargo all loading conditions up to full GAWR.
540 STARTING AND OPERATING The entire vehicle should first be weighed on a commer- CAUTION! cial scale to insure that the GVWR has not been exceeded. The weight on the front and rear of the vehicle should Do not load your vehicle any heavier than the GVWR then be determined separately to be sure that the load is or the maximum front and rear GAWR.
STARTING AND OPERATING 541 Common Towing Definitions Gross Combination Weight Rating (GCWR) The following trailer towing related definitions will assist The GCWR is the total permissible weight of your vehicle you in understanding the following information: and trailer when weighed in combination. Gross Vehicle Weight Rating (GVWR) NOTE: The GCWR rating includes a 150 lbs (68 kg) The GVWR is the total allowable weight of your vehicle.
Page 544
542 STARTING AND OPERATING Trailer Sway Control WARNING! The trailer sway control can be a mechanical telescoping link that can be installed between the hitch receiver and It is important that you do not exceed the maximum the trailer tongue that typically provides adjustable fric- front or rear GAWR.
Page 545
STARTING AND OPERATING 543 Weight-Carrying Hitch in accordance with the manufacturer’s directions, it pro- A weight-carrying hitch supports the trailer tongue vides for a more level ride, offering more consistent weight, just as if it were luggage located at a hitch ball or steering and brake control, thereby enhancing towing some other connecting point of the truck.
Page 546
544 STARTING AND OPERATING WARNING! • An improperly adjusted weight distributing hitch system may reduce handling, stability and braking performance and could result in a collision. • Weight distributing systems may not be compat- ible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable Rec- reational Vehicle...
Page 547
STARTING AND OPERATING 545 EXAMPLE — With Weight-Distributing Hitch (Correct) EXAMPLE — Improper Adjustment of Weight-Distributing Hitch (Incorrect) Fifth-Wheel Hitch The fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed.
546 STARTING AND OPERATING Gooseneck Hitch Trailer Hitch Classification Definitions The gooseneck hitch employs a pivoted coupling arm Class Max. Trailer Hitch Industry which attaches to a ball mounted in the bed of a pickup Standards truck. The coupling arm connects to the hitch mounted Heavy Duty over the rear axle in the truck bed.
Page 549
STARTING AND OPERATING 547 Ram 1500 4x2 SLT/Outdoorsman/Sport Laramie 3.7L V-6 4–Speed Towing: 3,750 lbs Automatic Transmission (1701 kg) - max — — Payload: 1,860 lbs (839 kg) - max 4.7L V-8 6–Speed Towing: 5,000 lbs Towing: 5,000 lbs (2268 kg) - std (2268 kg) - std Automatic Transmission 7,600 lbs (3447 kg) - max...
Page 550
548 STARTING AND OPERATING Ram 1500 4x4 SLT/Outdoorsman/Sport Laramie 4.7L V-8 6–Speed Towing: 5,000 lbs Towing: 5,000 lbs Automatic Transmission (2268 kg) - std (2268 kg) - std 7,400 lbs (3356 kg) - max 7,450 lbs (3379 kg) - max —...
Page 551
STARTING AND OPERATING 549 Ram 2500 & 3500 2500 Power Wagon 2500 ST SLT Bighorn/ 3500 ST SLT Bighorn/ Lonestar Laramie Out- Lonestar Laramie Out- doorsman doorsman 5.7L HEMI V-8 6-Speed Towing: 10,100 lbs Towing: 12,300 lbs Automatic Transmission (4581 kg) - max (5579 kg) - max —...
550 STARTING AND OPERATING NOTE: For additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • http://www.ramtrucks.com. • http://www.ramtruck.ca (Canada). Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer.
STARTING AND OPERATING 551 NOTE: Remember that everything put into or on the CAUTION! (Continued) trailer adds to the load on your vehicle. Also, additional • Then, during the first 500 miles (805 km) that a factory-installed options or dealer-installed options must trailer is towed, do not drive over 50 mph be considered as part of the total load on your vehicle.
Page 554
552 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Make certain that the load is secured in the trailer • Vehicles with trailers should not be parked on a and will not shift during travel. When trailering grade. When parking, apply the parking brake on cargo that is not fully secured, dynamic load shifts the tow vehicle.
Page 555
STARTING AND OPERATING 553 Towing Requirements – Tires replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s • Do not attempt to tow a trailer with less than the full GVWR and GAWR limits. size spare tire.
Page 556
554 STARTING AND OPERATING CAUTION! WARNING! (Continued) • Towing any trailer will increase your stopping If the trailer weighs more than 1,000 lbs (454 kg) distance. When towing you should allow for addi- loaded, it should have its own brakes and they tional space between your vehicle and the vehicle should be of adequate capacity.
Page 557
STARTING AND OPERATING 555 This display may also be used to display diagnostic information, if needed. • SC — Short Circuit to Ground • Sb — Short to Battery • CF — Controller Fault – If this message appears on the display, see your authorized dealer.
Page 558
556 STARTING AND OPERATING The trailer and the vehicle’s brake lamps will come on GAIN when either vehicle braking or manual trailer brakes are The GAIN setting is used to set the trailer brake control applied. for the specific towing condition and should be changed as towing conditions change.
Page 559
STARTING AND OPERATING 557 EVIC (if the connection is not recognized by the ITBM, 5. Press the SELECT button and then press the UP or braking functions will not be available), the GAIN setting DOWN buttons until Trailer Brake Type appears on the will illuminate and the correct type of trailer must be screen.
Page 560
558 STARTING AND OPERATING 6. Press the SELECT button and then press the UP or 7. Use the GAIN adjustment (+/-) buttons to increase or DOWN buttons until the proper Trailer Brake Type decrease the GAIN setting to the desired starting point. A appears on the screen.
Page 561
STARTING AND OPERATING 559 EVIC Display Messages WARNING! The trailer brake control interacts with the Electronic Vehicle Information Center (EVIC). Display messages, Connecting a trailer that is not compatible with the along with a single chime, will be displayed when a ITBM system may result in reduced or complete loss malfunction is determined in the trailer connection, of trailer braking.
Page 562
560 STARTING AND OPERATING Towing Requirements – Trailer Lights And Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package will include a four and seven- pin wiring harness.
STARTING AND OPERATING 561 WARNING! Any work done to the vehicle’s electrical system or wiring should be performed by a qualified automo- tive technician. If done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury. Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer up in an area away from heavy...
Page 564
562 STARTING AND OPERATING NOTE: Using “TOW/HAUL” mode or a lower gear Electronic Speed Control – If Equipped range while operating the vehicle under heavy operating − Do not use in hilly terrain or with heavy loads. conditions will improve performance and extend trans- mission life by reducing excessive shifting and heat build −...
STARTING AND OPERATING 563 − Air Conditioning CAUTION! Turn off temporarily. Using this vehicle for snowplow applications can SNOWPLOW cause damage to the vehicle. 1500 Models Only WARNING! NOTE: Do not use this model vehicle for snowplow applications. Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in a collision.
Page 566
564 STARTING AND OPERATING Builders Guide. See your authorized dealer, installer or Before Plowing snowplow manufacturer for this information. There are • Check the hydraulic system for leaks and proper fluid unique electrical systems that must be connected to level. properly assure operator safety and prevent overloading •...
Page 567
STARTING AND OPERATING 565 2. The total GVWR or the Front GAWR or the Rear The blade should be lowered whenever the vehicle is GAWR should never be exceeded. parked. 3. Cargo capacity will be reduced by the addition of Maintain and operate your vehicle and snowplow equip- options or passengers, etc.
Page 568
566 STARTING AND OPERATING cleaned. Reduce speed and use extreme caution when Keep all snowplow electrical connections and battery plowing unfamiliar areas or under poor visibility. terminals clean and free of corrosion. NOTE: During snowplow usage on vehicles equipped When plowing snow, to avoid transmission and drive- with outside temperature display, the display may show train damage, the following precautions should be ob- higher temperatures than the outside ambient tempera-...
STARTING AND OPERATING 567 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF The Two-Wheel Drive Four-Wheel Drive Models Ground Models See Instructions • Transmission in PARK Flat Tow NONE NOT ALLOWED • Transfer case in NEUTRAL (N) •...
568 STARTING AND OPERATING Recreational Towing – Two-Wheel Drive Models 5. Remove the key fob from the ignition switch. DO NOT flat tow this vehicle. Damage to the drivetrain 6. Install a suitable clamping device, designed for tow- will result. ing, to secure the front wheels in the straight position.
STARTING AND OPERATING 569 Recreational Towing – Four-Wheel Drive Models CAUTION! (Continued) NOTE: Both the manual shift and electronic shift trans- • Automatic transmissions must be placed in the fer cases must be shifted into NEUTRAL (N) for recre- PARK position for recreational towing. ational towing.
Page 572
570 STARTING AND OPERATING Shifting Into NEUTRAL (N) – Manual Shift CAUTION! Transfer Case (If Equipped) Use the following procedure to prepare your vehicle for It is necessary to follow these steps to be certain that recreational towing. the transfer case is fully in NEUTRAL (N) before recreational towing to prevent damage to internal WARNING! parts.
Page 573
STARTING AND OPERATING 571 9. Repeat steps 7 and 8 with transmission in DRIVE. Shifting Out Of NEUTRAL (N) – Manual Shift Transfer Case (If Equipped) 10. Turn OFF the engine. Use the following procedure to prepare your vehicle for 11.
Page 574
572 STARTING AND OPERATING 7. Shift the transmission into PARK. Shifting Into NEUTRAL – Electronic Shift Transfer Case (If Equipped) 8. Release the brake pedal. Use the following procedure to prepare your vehicle for 9. Disconnect vehicle from the tow vehicle. recreational towing: 10.
Page 575
STARTING AND OPERATING 573 light will blink while the shift is in progress. The light CAUTION! will stop blinking (stay on solid) when the shift to NEUTRAL is complete. It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recre- 7.
Page 576
574 STARTING AND OPERATING • Steps 1 through 5 are requirements that must be met CAUTION! prior to pressing the NEUTRAL button, and must continue to be met until the shift has been completed. Damage to the transmission may occur if the trans- If any of these requirements are not met prior to mission is shifted into PARK with the transfer case in pressing the NEUTRAL button or are no longer met...
Page 577
STARTING AND OPERATING 575 Shifting Out Of NEUTRAL – Electronic Shift 8. After the NEUTRAL button has been released, the Transfer Case (If Equipped) transfer case will shift to the position indicated by the Use the following procedure to prepare your vehicle for selector switch.
Page 578
576 STARTING AND OPERATING • The ignition switch must be in the ON/RUN position NOTE: • Steps 1 through 5 are requirements that must be met for a transfer case shift to take place and for the prior to pressing the transfer case NEUTRAL button position indicator lights to be operable.
WHAT TO DO IN EMERGENCIES CONTENTS ▫ To Stow The Flat Or Spare ....599 Hazard Warning Flashers ....579 If Your Engine Overheats .
Page 580
578 WHAT TO DO IN EMERGENCIES ▫ Center Console Shifter — If Equipped ..607 ▫ Two-Wheel Drive Models ....610 ▫ Four-Wheel Drive Vehicles ....611 Towing A Disabled Vehicle .
WHAT TO DO IN EMERGENCIES 579 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the upper switch bank just below the radio. potential for overheating by taking the appropriate action. •...
580 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING CAUTION! WARNING! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H,” • Do not attempt to change a tire on the side of the pull over and stop the vehicle.
WHAT TO DO IN EMERGENCIES 581 tab. Once the front of the cover is loose, slide the cover WARNING! (Continued) toward the front of the seat until it is free from the seat • The jack is designed to be used as a tool for frame.
Page 584
582 WHAT TO DO IN EMERGENCIES Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat. Jack And Tools (2500/3500 Series) Jack And Tools (1500 Series)
Page 585
WHAT TO DO IN EMERGENCIES 583 2. Position the jack and tool bag (unrolled). Make sure WARNING! the lug wrench is under the jack near the jack turn-screw. After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid accelera- tion or sharp turns.
Page 586
584 WHAT TO DO IN EMERGENCIES 3. Fold the flap and roll the jack tool kit into a cylindrical package (in direction of arrows) and tie to the jack using the tie straps. Tying Bag To Jack With Straps Folding Flap And Rolling Bag...
Page 587
WHAT TO DO IN EMERGENCIES 585 Jack And Tools Tied Jack And Tools (1500 Series) 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor, and then secure to the floor pan using the wing bolt.
586 WHAT TO DO IN EMERGENCIES Removing The Spare Tire Remove the spare tire before attempting to jack up the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube.
WHAT TO DO IN EMERGENCIES 587 NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas.
588 WHAT TO DO IN EMERGENCIES 4. Place the shift lever into PARK. On four-wheel drive Instructions vehicles, shift the transfer case to the 4L position. WARNING! 5. Turn the ignition OFF. Carefully follow these tire changing warnings to 6. Block both the front and rear of the help prevent personal injury or damage to your wheel diagonally opposite the jacking vehicle:...
Page 591
WHAT TO DO IN EMERGENCIES 589 WARNING! (Continued) CAUTION! • Do not let anyone sit in the vehicle when it is on a Do not attempt to raise the vehicle by jacking on jack. locations other than those indicated in the Jacking •...
Page 592
590 WHAT TO DO IN EMERGENCIES • 1500 Series Trucks When changing a front wheel, place the scissors jack under the rear portion of the lower control arm as shown below. 4X4 Jacking Location Operate the jack using the jack drive tube and the wheel wrench.
Page 593
WHAT TO DO IN EMERGENCIES 591 For 4x2 and 4x4 trucks, when changing a rear wheel, Connect the jack tube extension and wheel wrench. assemble the jack drive tube to the jack and connect the CAUTION! drive tube to the extension tube. Place the jack under the axle between the wheel and the shock bracket with the Before raising the wheel off the ground, make sure drive tubes extending to the rear.
Page 594
592 WHAT TO DO IN EMERGENCIES • 2500/3500 Series Trucks Operate the jack using the jack drive tube and the wheel For 2500/3500 4x2 series trucks, when changing a front wrench. The tube extension, may be used, but is not wheel, place the bottle jack under the frame rail behind required.
Page 595
WHAT TO DO IN EMERGENCIES 593 4x4 Jacking Location Rear Jacking Location (All) For 4x2 and 4x4 trucks, when changing a rear wheel, Connect the jack tube extension and wheel wrench. assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
Page 596
594 WHAT TO DO IN EMERGENCIES 5. Remove the wheel nuts and pull the wheel off. On CAUTION! single rear-wheel (SRW) trucks, install the spare wheel and wheel nuts with the cone shaped end of the wheel Before raising the wheel off the ground, make sure nuts toward the wheel.
WHAT TO DO IN EMERGENCIES 595 Hub Caps/Wheel Covers — If Equipped WARNING! The hub caps must be removed before raising the vehicle off the ground. A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Al- For 2500/3500 single rear-wheel (SRW) models, use the ways stow the jack parts and the extra tire and wheel blade on the end of the lug wrench to pry the hub cap off.
596 WHAT TO DO IN EMERGENCIES nut bolt circle and strike the high side down with a CAUTION! rubber mallet. Be sure that the hub caps and wheel skins • Use a back-and-forth motion to remove the hub are firmly seated around the wheel. cap.
Page 599
WHAT TO DO IN EMERGENCIES 597 Type Stud Torque Torque Disc Wheels Size Size Ft Lbs Newton Meters Cone M14 x 1.5 22 mm 120-150 160-200 Flanged M14 x 1.5 22 mm 130-160 190-220 8-Stud — Dual Rear Wheels Dual wheels are flat-mounted and center-piloted. The lug nuts are a two-piece assembly.
Page 600
598 WHAT TO DO IN EMERGENCIES Slots in the wheels will assist in properly orienting the These dual rear wheels should be tightened as follows: inner and outer wheels. Align these slots when assem- bling the wheels for best access to the tire valve on the inner wheel.
WHAT TO DO IN EMERGENCIES 599 2. Retighten the wheel nuts in the same sequence to the WARNING! torques listed in the table. Go through the sequence a second time to verify that specific torque has been A loose tire thrown forward in a collision or hard achieved.
600 WHAT TO DO IN EMERGENCIES HOISTING NOTE: When using a portable battery booster pack A conventional floor jack may be used at the jacking follow the manufacturer’s operating instructions and locations. Refer to the graphics that show jacking loca- precautions.
WHAT TO DO IN EMERGENCIES 601 Preparations For Jump-Start WARNING! The battery in your vehicle is located in the front of the • Take care to avoid the radiator cooling fan when- engine compartment, behind the left headlight assembly. ever the hood is raised. It can start anytime the NOTE: The positive battery post is covered with a ignition switch is on.
602 WHAT TO DO IN EMERGENCIES 3. If using another vehicle to jump-start the battery, park CAUTION! the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. Failure to follow these procedures could result in damage to the charging system of the booster vehicle WARNING! or the discharged vehicle.
Page 605
WHAT TO DO IN EMERGENCIES 603 8. Disconnect the opposite end of the positive (+) jumper WARNING! cable from the positive (+) post of the booster battery. Do not connect the cable to the negative post (-) of the 9. Disconnect the positive (+) end of the jumper cable discharged battery.
604 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE CAUTION! If the vehicle becomes stuck in snow, sand or mud, it can • When “rocking” a stuck vehicle by moving be- often be moved by a rocking motion. Move the shift lever rhythmically between DRIVE and REVERSE while ap- tween DRIVE and REVERSE, do not spin the plying slight pressure to the accelerator.
WHAT TO DO IN EMERGENCIES 605 WARNING! WARNING! • Chains are not recommended for freeing a stuck Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or vehicle. Chains may break, causing serious injury even failure, of the axle and tires.
606 WHAT TO DO IN EMERGENCIES SHIFT LEVER OVERRIDE If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use one of the following procedures to temporarily move the shift lever: Column Shifter — If Equipped 1.
WHAT TO DO IN EMERGENCIES 607 Center Console Shifter — If Equipped To access the override, carefully remove (using a flat- bladed screwdriver) the override access cover which is located on the right of the shift lever gate. 1. Firmly set the parking brake. 2.
608 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial wrecker service. If the transmission and drivetrain are operable, disabled vehicles may also be towed as described under “Recreational Towing”...
Page 611
WHAT TO DO IN EMERGENCIES 609 Proper towing or lifting equipment is required to prevent If the vehicle’s battery is discharged, see “Shift Lever damage to your vehicle. Use only tow bars and other Override” in “What To Do In Emergencies” for instruc- equipment designed for the purpose, following equip- tions on shifting the automatic transmission out of the ment manufacturer’s instructions.
610 WHAT TO DO IN EMERGENCIES Towing Without The Ignition Key Fob CAUTION! Special care must be taken when the vehicle is towed with the ignition in the LOCK/OFF position. The only Towing faster than 30 mph (48 km/h) or farther than approved method of towing without the ignition key is 15 miles (24 km) with rear wheels on the ground can with a flatbed truck.
WHAT TO DO IN EMERGENCIES 611 Four-Wheel Drive Vehicles CAUTION! The manufacturer recommends towing with all wheels • Front or rear wheel lifts should not be used. OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of vehicle raised and Internal damage to the transmission or transfer the opposite end on a towing dolly.
MAINTAINING YOUR VEHICLE 619 ONBOARD DIAGNOSTIC SYSTEM (OBD II) CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic further damage to the emission control system.
620 MAINTAINING YOUR VEHICLE the SELECT button to turn off the message. If the Normally, the OBD II system will be ready. The OBD II problem continues, the message will appear the next time system may not be ready if your vehicle was recently the vehicle is started.
MAINTAINING YOUR VEHICLE 621 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced a.
622 MAINTAINING YOUR VEHICLE DEALER SERVICE MAINTENANCE PROCEDURES Your authorized dealer has the qualified service person- The pages that follow contain the required maintenance nel, special tools, and equipment to perform all service services determined by the engineers who designed your operations in an expert manner.
MAINTAINING YOUR VEHICLE 623 The best time to check the engine oil level is about five CAUTION! (Continued) minutes after a fully warmed up engine is shut off. • Your vehicle has been built with improved fluids Checking the oil while the vehicle is on level ground will that protect the performance and durability of improve the accuracy of the oil level readings.
Page 626
624 MAINTAINING YOUR VEHICLE NOTE: Under no circumstances should oil change CAUTION! intervals exceed 8,000 miles (13 000 km) or six months, whichever occurs first. Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is Engine Oil Selection not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 625 Lubricants which do not have both the engine oil certi- Disposing Of Used Engine Oil And Oil Filters fication mark and the correct SAE viscosity grade num- Care should be taken in disposing of used engine oil and ber should not be used.
626 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Engine Air Cleaner Filter Selection Refer to the “Maintenance Schedule” for the proper The quality of replacement engine air cleaner filters maintenance intervals. varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR engine air WARNING! cleaner filters are a high quality filter and are recommended.
Page 629
MAINTAINING YOUR VEHICLE 627 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can • It is essential when replacing the cables on the burn or even blind you. Do not allow battery fluid battery that the positive cable is attached to the to contact your eyes, skin, or clothing.
628 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance WARNING! For best possible performance, your air conditioner • Use only refrigerants and compressor lubricants should be checked and serviced by an authorized dealer at the start of each warm season. This service should approved by the manufacturer for your air condi- include cleaning of the condenser fins and a performance tioning system.
MAINTAINING YOUR VEHICLE 629 Refrigerant Recovery And Recycling tailgate, sliding doors and hood hinges, should be lubri- R-134a Air Conditioning Refrigerant is a hydrofluoro- cated periodically with a lithium based grease, such as carbon (HFC) that is endorsed by the Environmental MOPAR Spray White Lube or equivalent, to assure Protection Agency (EPA) and is an ozone-saving product.
630 MAINTAINING YOUR VEHICLE Windshield Wiper Blades Adding Washer Fluid Clean the rubber edges of the wiper blades and the The fluid reservoir is located under the hood and should windshield periodically with a sponge or soft cloth and a be checked for fluid level at regular intervals.
MAINTAINING YOUR VEHICLE 631 Exhaust System WARNING! The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust Commercially available windshield washer solvents system. are flammable. They could ignite and burn you. Care must be exercised when filling or working around If you notice a change in the sound of the exhaust system;...
Page 634
632 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Exhaust gases can injure or kill. They contain • The catalytic converter requires the use of un- carbon monoxide (CO), which is colorless and leaded fuel only. Leaded gasoline will destroy the odorless. Breathing it can make you unconscious effectiveness of the catalyst as an emissions con- and can eventually poison you.
Page 635
MAINTAINING YOUR VEHICLE 633 Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter dam- verter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage.
634 MAINTAINING YOUR VEHICLE Cooling System Check the coolant recovery bottle tubing for brittle rub- ber, cracking, tears, cuts and tightness of the connection WARNING! at the bottle and radiator. Inspect the entire system for leaks. You or others can be badly burned by hot coolant or With the engine at normal operating temperature (but steam from your radiator.
Page 637
MAINTAINING YOUR VEHICLE 635 Refer to the “Maintenance Schedule” for the proper CAUTION! (Continued) maintenance intervals. • Do not use water alone or alcohol-based engine Selection Of Coolant coolant (antifreeze) products. Do not use addi- Use only the manufacturer’s recommended engine cool- tional rust inhibitors or antirust products, as they ant (antifreeze).
Page 638
636 MAINTAINING YOUR VEHICLE Please review these recommendations for using Hybrid Please note that it is the owner’s responsibility to main- Organic Additive Technology (HOAT) engine coolant tain the proper level of protection against freezing ac- (antifreeze). When adding engine coolant (antifreeze): cording to the temperatures occurring in the area where the vehicle is operated.
Page 639
MAINTAINING YOUR VEHICLE 637 Disposal Of Used Coolant WARNING! Used ethylene glycol-based engine coolant (antifreeze) is • The warning words “DO NOT OPEN HOT” on a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal the cooling system pressure cap are a safety pre- rules for your community.
Page 640
638 MAINTAINING YOUR VEHICLE To check the coolant level: 1. Open the coolant reservoir. 3. Check the coolant level on the dipstick. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for 2.
Page 641
MAINTAINING YOUR VEHICLE 639 • Do not overfill the coolant recovery bottle. of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once • Check engine coolant (antifreeze) freeze point in the a month.
640 MAINTAINING YOUR VEHICLE • Keep the front of the radiator clean. If your vehicle is WARNING! equipped with air conditioning, keep the front of the condenser clean, also. Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or •...
Page 643
MAINTAINING YOUR VEHICLE 641 With disc brakes the fluid level can be expected to fall as WARNING! the brake linings wear. However, an unexpected drop in • Use only manufacturer’s recommended brake fluid level may be caused by a leak and a system check should be conducted.
642 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Do not allow petroleum based fluid to contami- moisture, use only new brake fluid or fluid that nate the brake fluid. Brake seal components could has been in a tightly closed container.
Page 645
MAINTAINING YOUR VEHICLE 643 For 1500 Model axles, the fluid level should be even with NOTE: The presence of water in the gear lubricant will the bottom of the fill hole (within 1/4 in (6.4 mm) of edge result in corrosion and possible failure of differential of hole) for the FDU215 HD front axle and C235FE rear components.
644 MAINTAINING YOUR VEHICLE Transfer Case Automatic Transmission Drain And Refill Selection Of Lubricant Refer to the “Maintenance Schedule” for the proper It is important that the proper lubricant is used in the maintenance intervals. transmission to assure optimum transmission perfor- mance.
Page 647
MAINTAINING YOUR VEHICLE 645 Fluid Level Check CAUTION! (Continued) The fluid level should be checked when the engine is • Using a transmission fluid other than the manu- fully warmed up and the fluid in the transmission is at facturer’s recommended fluid may cause deterio- normal operating temperature.
Page 648
646 MAINTAINING YOUR VEHICLE 3. Fully apply the parking brake and press the brake between the two “COLD” (lower) holes on the dipstick pedal. with the fluid at approximately 70°F (21°C) (room tem- perature). If the fluid level is correctly established at 4.
MAINTAINING YOUR VEHICLE 647 dipstick cap to spring back slightly from its fully seated trees and road surfaces during other seasons, are highly position, as long as its seal remains engaged in the corrosive to the metal in your vehicle. Outside parking, dipstick tube.
Page 650
648 MAINTAINING YOUR VEHICLE • Insects, tree sap and tar. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. CAUTION! •...
Page 651
MAINTAINING YOUR VEHICLE 649 • If you detect any stone chips or scratches in the paint, Wheel And Wheel Trim Care touch them up immediately. The cost of such repairs is • All wheels and wheel trim, especially aluminum and considered the responsibility of the owner.
Page 652
650 MAINTAINING YOUR VEHICLE Stain Repel Fabric Cleaning Procedure – If Interior Care Equipped Use MOPAR Total Clean or equivalent to clean fabric Stain Repel seats may be cleaned in the following man- upholstery and carpeting. ner: Use MOPAR Total Clean or equivalent to clean vinyl •...
Page 653
MAINTAINING YOUR VEHICLE 651 Glass Surfaces WARNING! All glass surfaces should be cleaned on a regular basis with MOPAR Glass Cleaner or any commercial Do not use volatile solvents for cleaning purposes. household-type glass cleaner. Never use an abrasive type Many are potentially flammable, and if used in cleaner.
Page 654
652 MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be hauling and hard water stains. Weathering and UV used, but do not use high alcohol content or abrasive exposure will lead to fading, dulling, and loss of gloss cleaners.
Page 655
MAINTAINING YOUR VEHICLE 653 4. Once dry, apply a small amount of MOPAR occurs on your Spray-On Bedliner, rinse the truck out as Spray-On Bedliner Conditioner to a moist towel or soon as possible to avoid permanent damage. sponge and wipe over the entire surface of the truck Repairing The Spray-On Bedliner bedliner.
654 MAINTAINING YOUR VEHICLE FUSES Totally Integrated Power Module The Totally Integrated Power Module is located in the engine compartment near the battery. This center con- tains cartridge fuses and mini fuses. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart.
Page 657
MAINTAINING YOUR VEHICLE 655 Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 30 Amp Diesel Powertrain 30 Amp Transfer Case Module Pink Control Module – If Pink Equipped 30 Amp Rear Defroster 25 Amp Driver Door Node Pink Natural 60 Amp...
Page 658
656 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 30 Amp Front Wiper Ground/ 20 Amp Front Heated Seat & Pink Low/High Yellow Steering Wheel 20 Amp Washer Control 20 Amp Rear Heated Seats Blue Yellow 25 Amp...
Page 659
MAINTAINING YOUR VEHICLE 657 Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 20 Amp Main #2 Instrument 15 Amp Center Stop Lamp Yellow Cluster/Wireless Con- Blue trol Module/ITM/ 25 Amp Automatic Shutdown Siren/Multifunction Natural 1 and 2 Switch (Steering Col- 15 Amp Instrument Cluster...
Page 660
658 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 10 Amp Driver’s Door Switch 10 Amp Park Assist Module/ Climate Control Sys- tem Module/IR 10 Amp Ignition Switch Sensor/Compass Module 15 Amp Powertrain Control 15 Amp Left Front &...
MAINTAINING YOUR VEHICLE 659 VEHICLE STORAGE CAUTION! If you are storing your vehicle for more than 21 days, we • When installing the totally integrated power mod- recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: ule cover, it is important to ensure the cover is properly positioned and fully latched.
660 MAINTAINING YOUR VEHICLE NOTE: NOTE: For lighted switches, see your authorized dealer • When reinstalling the IOD fuse push firmly until fully for replacement instructions. seated; the gauges in the instrument cluster will do a All of the inside bulbs are brass or glass-wedge base. full sweep when the ignition switch is turned to the Aluminum base bulbs are not approved.
MAINTAINING YOUR VEHICLE 661 BULB REPLACEMENT Dual Or Quad Headlamp/Front Park And Turn Signal — If Equipped 1. Open the hood. 2. Disconnect and isolate the negative battery cable. 3. Remove the four plastic push-in fasteners that secure the upper radiator seal to the grille support and both fender ledges.
Page 664
662 MAINTAINING YOUR VEHICLE 8. Reach through the access hole of the wheel house 10. Disconnect the wiring harness connectors from the splash shield and lift the slide lock upward far enough to bulb socket. disengage it from the lock post on the back of the front 11.
MAINTAINING YOUR VEHICLE 663 Fog Lamps Rear Tail/Stop, Turn Signal And Backup Lamps 1. Reach under and behind the front bumper to access 1. Remove the two screws that pass through the bed the back of the front fog lamp housing. sheetmetal.
664 MAINTAINING YOUR VEHICLE 2. Pull the outboard side of the lamp rearward far 4. Rotate the bulb socket counterclockwise 1/4 turn to enough to unsnap the two receptacles on the outboard unlock it from the housing. side of the lamp housing from the two plastic snap post 5.
Page 667
MAINTAINING YOUR VEHICLE 665 2. Separate the connector holding the housing and wir- 3. Turn the desired bulb socket ⁄ turn and remove the ing harness to the body. socket and bulb from housing.
Page 668
666 MAINTAINING YOUR VEHICLE 4. Pull the desired bulb straight from the socket. CAUTION! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. •...
MAINTAINING YOUR VEHICLE 667 Cab Top Clearance Lamps — If Equipped 2. Rotate the socket ⁄ turn and pull it from the lamp assembly. 1. Remove the two screws from the top of the lamp.
668 MAINTAINING YOUR VEHICLE 3. Pull the bulb straight from it’s socket and replace. 2. Turn the socket ⁄ turn counterclockwise to access the bulb. Rear Lamp Bar ID Marker (Dual Rear Wheels) — If Equipped 3. Pull the bulb straight out from the socket. 1.
MAINTAINING YOUR VEHICLE 669 Side Marker Lamps (Dual Rear Wheels) — If 1. Push rearward on the side marker lamp assembly. Equipped 2. Pull the entire assembly from the fender. 3. Turn the socket ⁄ turn counterclockwise and remove from assembly to access the bulb. 4.
672 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hy- brid Organic Additive Technology) or equivalent. Engine Oil Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
Page 675
MAINTAINING YOUR VEHICLE 673 Component Fluid, Lubricant, or Genuine Part Fuel Selection – 3.7L and 4.7L 87 Octane Engines Fuel Selection – 5.7L Engine 87 Octane Acceptable - 89 Octane Recommended...
674 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission - Gasoline MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed Engines Only ATF+4 product. Transfer Case MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed ATF+4 product. Transfer Case – BW44–44 Only MOPAR BW44–44 Transfer Case Fluid or equivalent.
Page 678
676 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE On Non-EVIC equipped vehicles, “Change Oil” will flash The Scheduled Maintenance services listed in this in the instrument cluster odometer and a single chime manual must be done at the times or mileages specified will sound, indicating that an oil change is necessary. to protect your vehicle warranty and ensure the best Based on engine operation conditions, the oil change vehicle performance and reliability.
Page 679
MAINTENANCE SCHEDULES 677 NOTE: referring to the steps described under “Electronic Vehicle • The oil change indicator message will not monitor the Information Center (EVIC)/Oil Change Required” in time since the last oil change. Change your vehicle’s “Understanding Your Instrument Panel” or under “In- oil if it has been six months since your last oil change, strument Cluster Description/Odometer/Trip Odom- even if the oil change indicator message is NOT...
Page 680
678 MAINTENANCE SCHEDULES Once A Month CAUTION! • Check tire pressure and look for unusual wear or Failure to perform the required maintenance items damage. may result in damage to the vehicle. • Inspect the battery and clean and tighten the terminals as required.
Page 681
MAINTENANCE SCHEDULES 679 8,000 Miles (13,000 km) or 16,000 Miles (26,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
680 MAINTENANCE SCHEDULES 24,000 Miles (39,000 km) or 32,000 Miles (52,000 km) or 24 Months Maintenance Service 18 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 683
MAINTENANCE SCHEDULES 681 40,000 Miles (65,000 km) or 48,000 Miles (78,000 km) or 36 Months Maintenance Service 30 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 684
682 MAINTENANCE SCHEDULES 56,000 Miles (91,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 56,000 miles (91 000 km). ❏...
Page 685
MAINTENANCE SCHEDULES 683 64,000 Miles (104,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 64,000 miles (104 000 km). ❏...
Page 686
684 MAINTENANCE SCHEDULES 72,000 Miles (117,000 km) or 80,000 Miles (130,000 km) or 60 Months Maintenance Service 54 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 687
MAINTENANCE SCHEDULES 685 88,000 Miles (143,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). ❏...
Page 688
686 MAINTENANCE SCHEDULES 96,000 Miles (156,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). ❏...
Page 689
MAINTENANCE SCHEDULES 687 104,000 Miles (169,000 km) or 112,000 Miles (182,000 km) or 84 Months Maintenance Service 78 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 690
688 MAINTENANCE SCHEDULES 120,000 Miles (195,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). ❏...
Page 691
MAINTENANCE SCHEDULES 689 128,000 Miles (208,000 km) or 96 Months Maintenance Service 136,000 Miles (221,000 km) or Schedule 102 Months Maintenance ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 692
690 MAINTENANCE SCHEDULES 144,000 Miles (234,000 km) or 108 Months Maintenance Service 152,000 Miles (247,000 km) or Schedule 114 Months Maintenance ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 693
MAINTENANCE SCHEDULES 691 WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Suggestions For Obtaining Service For Your Vehicle......695 Speech Impaired (TDD/TTY) .
Page 696
694 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... 701 Department Of Transportation Uniform Tire Quality Grades ......701 ▫...
IF YOU NEED CONSUMER ASSISTANCE 695 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
696 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 solved with this process. Auburn Hills, MI 48321–8004 Phone: (866) 726–4636 •...
IF YOU NEED CONSUMER ASSISTANCE 697 Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
698 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment WARRANTY INFORMATION when you purchased the vehicle. An authorized dealer See the Warranty Information Booklet, located on the has also made a major investment in facilities, tools, and DVD, for the terms and provisions of Chrysler Group training to assure that you are absolutely delighted with LLC warranties applicable to this vehicle and market.
IF YOU NEED CONSUMER ASSISTANCE 699 If NHTSA receives similar complaints, it may open an In Canada investigation, and if it finds that a safety defect exists in If you believe that your vehicle has a safety defect, you a group of vehicles, it may order a recall and remedy should contact the Customer Service Department imme- campaign.
Page 702
700 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals • Owner’s Manuals These comprehensive Service Manuals provide the These Owner’s Manuals have been prepared with the information that students and professional technicians assistance of service and engineering specialists to need in diagnosing/troubleshooting, problem solving, acquaint you with specific Chrysler Group LLC ve- maintaining, servicing, and repairing Chrysler Group hicles.
Page 703
IF YOU NEED CONSUMER ASSISTANCE 701 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration.
Page 704
702 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 725
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehi- The antenna cable should be as short as practical and routed cle’s electronic system to provide immunity to radio frequency away from the vehicle wiring when possible. Use only fully signals.
Page 726
Chrysler Group LLC 12D241-126-AE 5th Edition Printed in U.S.A.