Related Manuals for Miele T 4123
Summary of Contents for Miele T 4123
-
Page 1: Operating Instructions
Operating instructions for vented tumble dryer T 4123 To avoid the risk of accidents or damage to the machine it is essential to read these Operating instructions before it is installed or used for the first time. M.-Nr. 06 067 720... -
Page 2: Table Of Contents
Contents Warning and Safety instructions ........4 Caring for the environment . - Page 3 Contents Installation ............24 Front view.
-
Page 4: Warning And Safety Instructions
This machine is not a toy! To avoid liability. Repairs should only be the risk of injury, do not allow undertaken by a Miele approved children to play on or near it, or to technician. play with the controls. Supervise its Ensure current is not supplied to the use by the elderly or infirm. - Page 5 Warning and Safety instructions If the connection cable is faulty it Adequate ventilation is essential, must only be replaced by a Miele especially where another approved service technician to protect appliance which also uses the room air the user from danger.
- Page 6 Always close the door after use. This way you will avoid the danger Accessory parts may only be fitted when expressly approved by Miele. – children climbing onto or into the If other parts are used, guarantee, dryer or hiding things in it.
-
Page 7: Caring For The Environment
Caring for the environment Disposal of the packing Energy saving tips material ^ Make sure that your laundry is thoroughly spun before drying. The transport and protective packing has been selected from materials which The higher the spin, the greater the are environmentally friendly for disposal savings that can be made in energy and can normally be recycled. -
Page 8: Control Panel
Control panel a Programme selector d I-On/0-Off button The programme selector can be To switch the machine on or off / to turned clockwise or anti-clockwise. interrupt a programme. b Programme sequence and check e Door Button lamps To open the door / to cancel a c Start button programme. -
Page 9: Notes On Laundry Care
Notes on laundry care Wash care labels Items filled with down. The fabric lining on these garments Before drying check the drying may shrink depending on the quality. symbol on the wash care label. They can be partially dried using the Smoothing programme. -
Page 10: Programme Chart
Programme chart Programmes Fabric type Special notes COTTONS maximum load: 5 kg Drying levels Normal+ Single and multi-layered fabrics, e.g. mixed load of cotton fabrics (e.g. towelling, jerseywear). Normal Load of similar cotton If laundry is still too damp, fabrics (jersey wear, then: flannelette sheets, - finish drying using Timed... - Page 11 Programme chart Programmes Fabric type Special notes MINIMUM IRON maximum load: 2.5 kg Drying levels Normal+ Minimum iron items which Spin minimum iron fabrics are made of synthetic or for at least 30 seconds in the blended fabrics (e.g. washing machine before pullovers, dresses, trousers) drying them.
- Page 12 Programme chart Programme Fabric type Special notes Special care programmes Woollens maximum load: 2 kg hand care Woollen fabrics To refresh and fluff up woollen garments quickly. Remove garments immediately at the end of the programme. Do not repeat. Woollen fabrics are not dried completely by this programme.
-
Page 13: How To Dry Correctly
How to dry correctly A Prepare the laundry Do not overload the drum. ^ As far as possible, sort laundry for: Overloading can cause unnecessary - the type of fibre or weave, wear and tear to the laundry and - the degree of dryness required, give a disappointing drying result. -
Page 14: C Select A Programme
How to dry correctly C Select a programme D Start the programme ^ Press the Start button. The drying cycle begins. The drying stage reached is shown by the sequence indicator lamps on the right hand side of the control panel. At the end of the drying phase a cooling down phase commences to cool the laundry down. -
Page 15: Selecting A Different Programme
How to dry correctly Selecting a different programme The programme has been successfully cancelled when only the As long as the cooling down phase or Anti-crease/Finish indicator lamp is on. the anti-crease phase has not been reached it is possible to change a E At the end of a programme programme after it has started by turning the programme selector to a... -
Page 16: Cleaning And Care
Cleaning and care Cleaning the fluff filter A cleaning brush is available as an optional extra from your Miele dealer The fluff which is created by the or the Miele Spare Parts Department. drying process is collected in the fluff You can also use a vacuum cleaner. -
Page 17: Tumble Dryer
^ Dry all parts with a soft cloth. E-Cloth A microfibre "E-Cloth" is available from the Miele UK Spare Parts Department, which is suitable for cleaning surfaces such as stainless steel, glass, plastic and chrome without the use of... -
Page 18: Problem Solving Guide
Problem solving guide With the help of the following notes minor faults in the performance of the machine, some of which may result from incorrect operation, can be put right without contacting the Service Department. Repair work to electrical equipment should only be carried out by a suitably qualified person in accordance with local and national safety regulations. - Page 19 Problem solving guide Problem Possible cause Remedy There is a build up of Fluff is principally the Fluff is collected by the fluff. result of friction when fluff filters and can be garments are being worn easily removed (see and washed. Machine "Cleaning and Care").
- Page 20 Problem solving guide Problem Possible cause Remedy The drying Important: Before attempting to remedy one of the following process goes on causes, switch the dryer off and switch on again to start the too long or even programme again. switches off. Ventilation to the dryer is Open a door or window while insufficient (e.g because it is...
- Page 21 – Then start the Hand iron or Machine programme again. iron is flashing, and If the programme stops the buzzer sounds. again and the fault message reappears there is a fault. Contact the Miele Service Department.
-
Page 22: To Change The Interior Drumlamp
^ Turn your wrist to make the cover open downwards. The temperature resistant lamp should only be ordered from your Miele dealer or the Miele Spare Parts Department. The lamp must not exceed the maximum wattage quoted on the data plate and on the lamp cover. -
Page 23: After Sales Service
Department, please quote the model Optional accessories for these dryers and serial number of your machine, are available from your Miele Dealer or both of which are shown on the data from the Miele Spare Parts Department. plate situated on the right hand side below the drum aperture. -
Page 24: Installation
Installation Front view a Venting connection: rear, right or left (supplied with the rear socket open) b Supply cable for electrical connection c Control panel d Door e Four height-adjustable screw feet... -
Page 25: Installation Site
Installation Installation site * Available as an optional accessory from your Miele dealer or the Miele Make sure the dryer door can be Spare Parts Department. opened without hindrance after The building under kit is supplied with installation. its own installation instructions. -
Page 26: Aligning The Machine
The machine must be perfectly level to * Available as an optional accessory ensure safe and proper operation. from your Miele dealer or the Miele Spare Parts Department. Stacking kits must only be installed by suitably qualified fitters. ^ The screw feet can be adjusted to compensate for any unevenness in the floor. -
Page 27: Electrical Connection
Electrical connection Electrical connection U.K. Electrical connection U.K. Non-rewireable plugs BS 1363 All electrical work should be carried out only by a suitably qualified and If this machine is fitted with a competent person, in strict accordance non-rewireable plug and the socket with national and local safety outlets are not suitable for the plug regulations. - Page 28 Electrical connection If the colours of the wires in the mains lead of this machine do not correspond with the coloured markings identifying the terminals of your plug, proceed as follows: ^ The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol z or coloured green, or...
-
Page 29: Installation - Venting
* Available from your Miele dealer or the – The ducting outlet (e.g. wall pipe) Miele Spare Parts Department. should be installed in such a way that the moist expelled air . -
Page 30: Calculating The Effective Duct Length
1. To calculate the effective duct stack)* length required: Venting connection to the left/right 1.0 m ^ First measure the distance which will * optional accessory from Miele require straight ducting. Multiply this Table II amount by the corresponding Maximum effective Internal duct additional duct length factor in Table I. -
Page 31: Installation To The Left Or Right Side Of The Machine
Installation - venting Installation to the left or right 3. Example side of the machine At the rear The connection is opened at the factory. ^ Fit one of the venting systems described on the following pages. Left or right side of the machine Wall pipe, with louvred vent = 1 x 3.8 m Additional duct = 3.8 m... -
Page 32: Adapter
^ The following items are required: ... flexible ducting hose ... a wall vent kit* or window vent kit*. * (Miele optional accessory). A ring adapter** (1) is installed in adapter (2) for the installation of a flexible vent duct. It reduces time and... - Page 33 Installation examples - venting Connection to an exhaust flue system with flexible ducting Window vent 1. Pipe with connection piece (= supplied with the Miele wall vent kit) 1. Window vent kit (fitted in a 2. Adapter for flexible hose "plexiglass" pane) (separate fitting instructions are 3.
-
Page 34: Venting System With Plastic Piping
If the total duct length is greater than 10 m the ring adapter is not required. plastic piping B Fit Miele adapter (2) into the vent Plastic piping is a good option where opening on the dryer. the vented air has to ducted for some C Attach the pipe (3). -
Page 35: Connecting Directly To A Wall Vent
^ A wall pipe and a flexible foam gasket must be used (both Miele optional accessories). A Before drilling into the wall . . . 1. Wall pipe 2. -
Page 36: Washer Dryer Stack
Washer dryer stack Miele washing machine with Comfort line angled fascia Height of venting outlet for washer dryer stack Miele washing machine with straight or sloping fascia Stacking kit* without worktop: C = 94.2 cm D = 170.0 cm Stacking kit* without worktop: Stacking kit* with worktop: A = 94.2 cm... -
Page 37: Consumption Data
Consumption data Programmes Capacity Final spin speed Electricity Drying time (in a domestic consumption (incl. washing machine) cooling down time) Minutes COTTONS Normal+ 1200 2.70 1400 2.60 1600 2.30 1800 2.25 Normal 800 (70 % residual moisture) 3.30 2.60 Normal 1200 1400 2.45... -
Page 38: Technical Data
Technical data Height 85 cm (adjustable +0.7/-0.7 cm) Height without lid 82 cm Depth with door open 106 cm Width 59.5 cm Depth 58 cm Weight 48 kg Drum volume 100 litres Maximum capacity 5 kg dry weight Length of connection cable 1.60 m Voltage see data plate... - Page 39 Programmable functions for changing standard settings...
-
Page 40: Programmable Functions
Programmable functions E Turn the programme selector to the Increased drying level in the COTTONS Normal position. COTTONS programmes – If the Drying indicator lamp is not on, The machine is designed to dry the increased drying level is using as little energy as possible. deactivated. -
Page 41: Increased Drying Level In The Minimum Iron Programmes
Programmable functions E Turn the programme selector to the Increased drying level in the COTTONS Low Temperature MINIMUM IRON programmes position. The machine is designed to dry – If the Drying indicator lamp is not on, using as little energy as possible. the increased drying level is However, if you require the laundry to deactivated. -
Page 42: Buzzer
Programmable functions E Turn the programme selector to the Buzzer COTTONS Hand iron position. An audible tone sounds repeatedly at – If the Drying lamp is flashing, the the end of a programme. buzzer is activated. The buzzer is activated as standard –... - Page 44 Alteration rights reserved/0504 M.-Nr. 06 067 720 / 00 This paper consists of cellulose which has been bleached without the use of chlorine.