Advertisement
VR-2OSO/VR-
2OSO/K
RF-VS881
DiKRF+V7771
[3 [En/K)
When
recording
sound
with
a recorder
component
of KENWOOD,
synchro
recording
is possible
by setting
the INPUT
SELECTOR
to select
"Tape1"
or "MD"
according
to the
connected
component.
Recording a music source
O Select
the recording
source.
The
icons differ according
to the
setup
of +Setup
IR"
etc.
19 Put the MD recorder
or cassette
deck to record-pause
mode.
Select the "Remote
Mode"
icon from the fixed
segments.
_+ Select
the "MD/Tapel"
icon,
Select
the MD or cassette
deck control
icon and put it to
record-pause
mode+
O Play the source
and record
it.
a When
the
"Remote
Mode"
con
is selected,
the
icons of the
components
assigned
to the inputS, such as the "CD1 ", "Video
1",
"Video2",
"Video3"
and "MD/Tapel"
icons
bnk
for a few
seconds+
By select;nO
a bI+nkng
icon,
the
selected
component
can
be
controled
without
switching
the
input selector
(The "Remote
Mode"
con
can be used to put the recording
component
to pause
mode
w thout switching
the input selectory
When
an icon that is not blinking
is selected,
the input selector
is
switched
automat
sally
• For the recerding
procedure
of the MD recorder
or cassette
oeck,
refer to its instruction
menus
Copying tape (TAPE1 --_ TAPE2)
l
O Select
the "MD/Tapel"
input.
|
O Startplayback
of the cassette
deck connected
to the MD/TAPE1
]
input
jacks,
then start
recording
of that
connected
to the CD2/
TAPE2
MONITOR
input
jacks+
Caution for recording
Digital--*
digital recording
The digital
signal
input
through
DIGITAL
IN is output
digitally
at
the OPTICAL
jack+
Make
sure the following
points
to record
a digital
signal
input
into
the receiver.
(The DTS and Dolby Digital
(AC-3}
signals
can-
not be recorded,)
Igl Connect
the
digital
output
from
the source
component
to the
digital
input of the receiver
O Connect
the digital
output
(OPTICAL
jack) of the receiver
to the
digital
input (OPTICAL
jack} of the MD recorder.
O Record the signal on the recorder
component
(MD recorderl
Digital-*
analog recording
By reproducing
the digital
signal
input
to the receiver
in stereo
(surround
mode),
the signal
can be recorded
in analog
with
the
following
procedure,
O Set up the recorder
component
+eady for recording
t_ Select
the receiver's
input
to the source
component,
_) Play the desired
software.
O Set the "Input
Digital"
icon from
"Auto"
to "Manual",
O In the "Lstn
Mode'*
menu
screen,
select
the
"Stereo"
icon
O PFay the software
from the beginning
and record it.
• Do not switch
to "CD2/Tape2
(Monitor)"
during
recording,
This may cause the interruption
of the recording,
Note on CD2/ Tape2 (Monitor)
The
following
operations
are made
available
by setting
the
"CD2/Tape2
(Monitor)"
icon
on the
"Setup
Input"
menu
screen
to
"Tape2
(Monitor)",
However,
remember
that
these
functions
are
available
only
when
the
analog
input/output
are used,
If the
"CD2/Tape2"
icon
in the fixed
segments
is selected
during
playback
of a digital
input,
the input
is switched
to the analog
input
and
noise
may
be generated.
"Tape2 (Monitor)" setup menu screen
For the setup
of the remote
control
unit,
p[ease read
"Set
"CD2/Tape2"",
ICON
DISPLAY
@
002 ! TAPE2
MONITOR
Using "CD2/Tape2"
The CD2/TAPE2
MONITOR
input jacks of the main unit accept
e cassette
deck or graphic
equalizer.
When
a graphic
eelJalizer
is connected,
set "CD2]Tape2"
to "Tape2"
and select
the "CD2/Tape2"
icon in the fixed segments
to on,
When
a 3+head cassette
deck is connected
to the CD2iTAPE2
MONITOR
_nput jacks,
the recorded
audio
can
be monitored
during
recording,
and turning
"CD2/Tape2"
on and off
allows
you to
compare
the source
audio
and recorded
audio
Refe
to the instructio_
manuals
of the connected
components
for the_
operating
procedures,
The "CD2/Tape2
(Monitor)"
funct+on
is not ave Jab e during
p ayback
of a digital
input
Se ecting
"CD2/Tspe2
(Monitor)"
durng
dig tal input playback
switches
the input to the analog
input
Advertisement
