Kenwood KRF-X9060D Instruction Manual page 24

Preparing for surround sound
8 Use the MULTI CONTROL knob or Joystick (5/∞) to select
the appropriate surround speaker setting.
If you selected "LARGE" as the center speaker setting,
1 SURR LARGE
2 SURR NML/THX : Average size surround speakers are
3 SURR OFF
If you selected other than "LARGE" as the center speaker
setting,
1 SURR NML/THX : Surround speaker setting mode to
2 SURR OFF
• When the setting "SURR OFF" is selected, the procedure skips
to step #.
9 Press the M M M M M key or Joystick (3) again to accept the setting.
• The surround speaker setting indication "SB" appears.
0 Use the MULTI CONTROL knob or Joystick (5/∞) to select
appropriate surround back speaker setting.
If you selected "LARGE" as the surround speaker setting,
1 SB NML/THX : Average size surround back speaker is
2 SB LARGE
3 SB OFF
SP MUTE OPTICAL 6CH INPUT
A B CLIP
COAXIAL ANALOG
L C SW R
LFE
SL S SB SR
If you selected other than "LARGE" as the surround speaker
setting,
1 SB NML/THX : Surround back speaker setting mode to
2 SB OFF
• After setting SB (surround back) from OFF to NML/THX, 6ch
AMP setup display will appear to enable you to re-select either
SW, SB or OFF from the surround back or subwoofer speaker
terminal.
! Press the M M M M M key or Joystick (3) again to accept the setting
and "SURR:MIX" appears.
• Surr:mix is when the SL and SR speakers signals are mixed to
produce sound from the surround back speaker which would
enable the listener to enjoy sound coming from the back.
SP MUTE OPTICAL 6CH INPUT
A B CLIP
COAXIAL ANALOG
L C SW R
LFE
SL S SB SR
@ Use the MULTI CONTROL knob or Joystick (5/∞) to select
the following.
1 SURR:MIX ON : Surround mix setting mode to the
2 SURR:MIX OFF : Surround mix setting mode to the
• If surround back speaker is turned OFF, SURR:MIX setting is not
visible and the procedure skips to step #.
24 EN
: Large surround speakers are con-
nected to the receiver.
connected to the receiver.
: Surround speaker setting mode to
the receiver is OFF.
the receiver is ON.
: Surround speaker setting mode to
the receiver is OFF.
connected to the receiver.
: Large surround back speaker is
connected to the receiver.
: Surround back speaker setting mode to
the receiver is OFF.
CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6
AUTO DETECT
ACTIVE EQ. MATRIX
96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII
the receiver is ON.
: Surround back speaker setting mode to
the receiver is OFF.
CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6
AUTO DETECT
ACTIVE EQ. MATRIX
96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII
receiver is ON.
receiver is OFF.
# Press the M M M M M key or Joystick (3) again to accept the setting.
• The subwoofer re-mix setting indication "SW RE-MIX" appears.
$ Use the MULTI CONTROL knob or Joystick (5/∞) to select
the appropriate subwoofer re-mix setting.
• If subwoofer is turned OFF, subwoofer re-mix setting is not
visible.
% Press the SETUP key again to return to the main setup displays.
• The receiver enters the speaker volume level adjustment mode.
• In steps 4 and 5, indications appear only for the selected
channels of the speakers that require adjusting.
4
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
1 Press the M M M M M /? ? ? ? ? keys or Joystick (2/3) to select TEST TONE.
2 Press the SETUP key for the following displays:
3 The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or Joystick (5/∞).
Press the SETUP key again to begin TEST TONE.
Use the MULTI CONTROL knob or Joystick (5/∞) to adjust
the volume level of the test tone output from the speaker
RDS
THX
channel to be adjusted.
RTY
Surround EX
AUTO
MEMO
STEREO
For AUTO selection, the first test tone is heard from the front
TUNED
left speaker for 2.5 seconds. The next test tone is heard from
the speakers in the following sequence for 2 seconds each.
When the 6ch AMP SB has been selected.
When the 6ch AMP SW or OFF has been selected.
The channel indication blinks while the test tone is being output.
L C
LFE
SL S SB
• If you change the volume level settings for the speakers while
RDS
listening to music, the settings referred to on this page are also
THX
RTY
Surround EX
AUTO changed.
MEMO
• If the speaker setting selects are OFF, the speaker level settings
STEREO
TUNED
are reset.
For MANUAL selection, press the M M M M M / ? ? ? ? ? keys or Joystick (2/3)
each time to select the speaker channel.
4 Press the SETUP key again.
• The test tone is turned off and return to the main setup displays.
1 SW RE-MIX ON : Subwoofer re-mix setting mode to
the receiver is ON.
2 SW RE-MIX OFF : Subwoofer re-mix setting mode to
the receiver is OFF.
1 T.TONE AUTO
2 T.TONE MANUAL
LEFT CNTR
SUBW SL
LEFT CNTR
SUBW SL
SP MUTE OPTICAL 6CH INPUT CINEMA EQ.
AUTO DETECT
ACTIVE EQ.
A B CLIP
COAXIAL ANALOG 96kHzfs DSP MODE
SW R
SR
RIGHT SR
SB
RIGHT SR
SBL SBR
DTS. DOLBY DIGITAL STEREO NEO:6 RDS
THX
MATRIX
RTY
Surround EX
DISCRETE PRO LOGIC LOUDNESS CSII
AUTO
MEMO
STEREO
TUNED
°