Lens Section - Sony HDR-CX360 Service Manual

2-1-4. LENS SECTION

(CX360/CX360E/CX360V/CX360VE/PJ30/PJ30E/PJ30V/PJ30VE/PJ40V)
Refer to page 2-7 about PJ10/PJ10E/PJ20.
C7210
154
(Note 4) #3
1 152
#3
151 #1
8
- 2 4
#2 S T
#12
#12
153
5
3 167
2
Ref. No. Part No. Description
151 A-1800-670-A LED BLOCK ASSY, ST
152 A-1810-651-A ST-248 BOARD, COMPLETE
153 1-882-882-11 FP-1327 FLEXIBLE BOARD
154 1-882-883-11 FP-1328 FLEXIBLE BOARD
155 1-818-890-11 CONNECTOR, EXTERNAL (HOT SHOE)
156 4-271-966-01 FRAME, SHOE
157 4-271-724-01 HEAT SINK (L) (381)
158 4-271-723-01 FRAME (L) (381), LENS
159 A-1767-897-A CM-114 BOARD, COMPLETE
(including CP002 (CMOS imager)) (Note 1)
160 3-216-044-01 RUBBER (1270), SEAL
161 1-856-172-21 FILTER BLOCK, OPTICAL (Note 2, 3)
162 1-856-171-21 FILTER BLOCK, OPTICAL (Note 2, 3)
163 1-882-879-11 FP-1324 FLEXIBLE BOARD
164 4-272-545-01 SHEET (CM (381)), SHIELD
165 A-1733-588-A DEVICE, LENS LSV-1400A (SERVICE)
166 4-276-408-01 SHEET (FPC (LENS))
167 A-1817-603-A VC-621 BOARD, COMPLETE (SERVICE)
(CX360/CX360E/CX360V/CX360VE)
HDR-CX360/CX360E/CX360V/CX360VE/PJ10/PJ10E/PJ20/PJ30/PJ30E/PJ30V/PJ30VE/PJ40V_L2
A6CCCE74558B3E905AD2CEF677F08944A4F35D719FFF538EDA3BBE0D0B9DF46BB1D7EBFA51D2D3C1
#1
4 155
156
#3
159
158
157 (including CP002 (CMOS imager))
(Note 1)
5-3
5-3
#3
160
161
#3
(Note 2, 3)
162
(Note 2, 3)
163
175
164
176
165
166
168
#3
#3
169
#3
Ref. No. Part No. Description
167 A-1817-605-A VC-621 BOARD, COMPLETE (SERVICE)
168 4-271-970-01 LABEL (381), CAUTION
169 A-1817-601-A LD-279 BOARD, COMPLETE (SERVICE)
(CX360/CX360E/CX360V/CX360VE/PJ30/PJ30E/PJ30V/PJ30VE)
169 A-1817-602-A LD-279 BOARD, COMPLETE (SERVICE) (PJ40V)
170 4-271-964-01 FRAME (R), LENS
171 4-271-965-01 HEAT SINK (R)
172 4-271-967-01 SHEET, CM RADIATION (Note 5)
173 4-271-968-01 SHEET (HEAT SINK R)
174 4-271-969-01 SHEET (FRAME R)
175 1-882-736-11 FP-1313 FLEXIBLE BOARD
176 4-272-050-01 SHEET (MM), SHIELD
C7210 1-116-781-11 CAP, DOUBLE LAYERS (Note 4)
#1 2-635-562-11 TITE (UB TITE) 1.4
#2 2-635-562-31 TITE (UB TITE) 1.4
#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2
#12 3-080-204-21 SCREW, TAPPING, P2
#172 2-178-410-01 TITE (UB TITE) 1.4
DISASSEMBLY
1. Remove to numerical order (
#2 X 1 → #3 X 1
1
#172
#3 X 2
3
170
5-2
172
(Note 5)
171 CM Radiation Sheet (5-1) → #3 X 3 → Heat Sink (R)/ Lens Frame (R) (5-2) → #12 X 2 → Heat Sink (L) (381)/ Lens Frame (L)(381) (5-3)
5
5-1
5-2
Left View
#3
Screw
173
174
#1: M1.7 X 2.5
(Black)
2-635-562-11
2.5
(PJ30/PJ30E/PJ30V/PJ30VE/PJ40V)
Note
Note 1: Be sure to read "Precautions for Replacement of Im-
ager" on page 6-1 of Level 3 when changing the imager.
Note 1:
Note 2: Refer to "Assembly-3: How to distinguish the side of
Optical Filter Block facing to Lens Device".
Note 2:
Note 3: Install the thin filter to the lens device side, and install
the thick filter in the ASM module side.
Note 3:
2-6
to ) in the left figure.
1 5
Left View Left View
#2 #3
4
Bottom View
#3
Bottom View
#3
#2: M1.7 X 4.0 #3: M1.7 X 2.5
(Black) (Red)
2-635-562-31 2-660-401-01
1.7 1.7 1.7
4.0
2.5
Note 4: This model is provided with a flash unit using LED
Note 4:
Note 5: The CM Radiation Sheet when peeling off once, so that
Note 5:
#3 X 2
2
Bottom View
#3
#3 X 2
Left View Right View
#3
#3
Top View
Left View
#12
#3
#12: M1.7 X 5.0 (Tapping) #172: M1.4 X 4.0 (Tapping)
(Black) (Black)
3-080-204-21
2-178-410-01
1.7 1.4
5.0 4.0
light.
Therefore, the flash unit does not need to be dis-
charged.
itcannot be reused.