Advertisement
Electronic Controh
(continued)
Automatic Oven Timer
The oven timer will automatically
start and stop your oven cooking
operation for you.
For automatic oven cooking:
1.
Push COOK TIME button.
2. Turn SET knob to set length of
baking time.
3. Push BAKE button.
4. Turn SET knob to set desired
temperature.
When cook time is reached, the
End-of-Cycle Tone will sound and
the oven will turn off.
During automatic cooking:
Youcan push the STOP TIME
button to find out when the End-of-
Cycle Tone will sound and the oven
will turn off.
Youcan push the CLOCK button
to display time of day without
canceling the oven operation.
ToDelay Starting an
Automatic Oven Operation
If a delayed cooking operation
is desired:
1.
Push COOK TIME button.
2. Set length of baking time with
SET knob.
3. Push S'IOP TIME button.
4. Turn SET knob to time of day
baking should be completed. Time
should be greater then COOK TIME.
5. Push BAKE button.
6. Turn SET knob to desired
temperature.
When stop time is reached, the
End-of-Cycle Tone will sound and
the oven will turn off.
Caution: Never let food sit in the
oven for more than 4 hours before
cooking starts.
Room temperature
is ideal for the growth of harmful
bacteria. Be sure oven light is off
because heat from the bulb will
speed bacteria growth.
Note:
Youcan push the STOP
TIME button to find out when the
oven will turn off. Push and hold
the COOK TIME button to find out
when the oven will turn on.
How to Change
a Program
When a function has been
entered, you can recall what has
been programmed by pushing
the corresponding function
button. The messages in the
displayshow you which fhnction
is currently being displayed.
While the function is displayed,
you can change it with the SET
knob. Youcan change any
programmed function at any
time.
f%
Tones
End*f-Cycle
Tone (3
long beeps—
one second on, one second off):
t
shows that a timed oven operation
has reached S'IOP TIME or that
~
the Minute/Second Timer has
counted down.
Attention Tone
(series of short
beeps, l/4-second on, l/4-second
off, until proper response is given):
will sound if oven has only been
partially programmed. For example,
if you have selected a cook time but
no temperature, you will hear the
Attention Tone until you select a
temperature or push oven CANCEL.
Notification Tone
(single, one-
second beep): indicates oven has
stabilized at selected temperature.
Key Tone
(single, l/10-second
beep): sounds when any button
is pushed.
Function Error Tone
(series of
very rapid beeps, l/8-second on,
'%
+
l/4-second off): display will show a" '
failure code. Cancel Function Error
Tone by pushing the oven CANCEL
button. If the Function Error Tone
starts again (after about 15seconds),
call for service. Disconnect the range
electrical supply to stop the tone.
If the function error occurred
while you were programming the
Electronic Control, push the oven
CANCEL button and try again.
To Cancel the Tone...
If you don't
want an audible tone at the end of a
cycleor when you push a button, you
can eliminate the End-of-Cycle and
KeyToneby pushing and holding the
oven CANCEL button until you
hear a short beep (in approximately
two seconds). To activate the tones
again, push and hold the oven
CANCEL button once more until
you hear a short beep. Canceling
or activating the tones should only
be done when there is no oven
operation programmed.
3
Pushing the
oven CANCEL
button ".. '
will clear all fi.mctions except the
Clock and Minute/Second Timer.
14
Advertisement
