Related Manuals for LONGHORN LHD8003
Summary of Contents for LONGHORN LHD8003
- Page 1 Arm Away 2 0 / 1 2 / 2 0 1 0 1 5 : 3 0 MGE Entreprise Av. Kouwait - 8050 Hammamet Tunisie Tel.1: 00216 72 278 663 Tel.2: 00216 22 645 120 Email: manager@mge-security.com www.mge-security.com/...
- Page 2 CREATING SECURITY SOLUTION...
-
Page 3: Installation Information
INSTALLATION INFORMATION User Name User Address Installer Name Installation Company Installation Date Phone of Installation Company Fax of Installation Company Control Panel ID Control Panel Phone NO. CMS 1 CMS 1 Address CMS 1 Phone NO. CMS 2 CMS 2 Address CMS 2 Phone NO. -
Page 4: Packing List
Appendix 5: Zone Type Setting Figure PACKING LIST Type Bypass or not Zone NO. Installation Position Item Description Quantity Control Panel Keyfob Wireless PIR Detector Wireless Magnetic Switch Power Adaptor Installation Manual Accessory Bag Installing Hole Drawing Note : It should include screws (4pcs ), EOL resistance (2.2K, 4pcs) and dowels (4pcs) in the accessory bag . -59-... -
Page 5: Table Of Contents
TABLE OF CONTENTS Appendix 4: Ter m Definitions ◆ Detector: A facility that detects intrusion and abnormal state automatically via some electric or Chapter 1 : Introduction ------------------------------------------------------------------------ 3 physical methods and output switch signals or wireless signals to the system for disposal, then output Chapter 2 : Specifications --------------------------------------------------------------------- 3 alarm signals, such as infrared detector, smoke detector, etc. - Page 6 7.1.3. Disarm --------------------------------------------------------------------------------------------------- 23 Appendix 3: Communication Protocol and Codes 7.2. Arm/Disarm via Phone ------------------------------------------------------------------------------------------- 24 Table 1: Contact ID Event Code 7.3. Arm/Disarm via SMS ---------------------------------------------------------------------------------------------- 24 CID Code Definition 7.4. Trigger Alarm via Keypad ---------------------------------------------------------------------------------------- Panic Alarm Chapter 8 : Programming ------------------------------------------------------------------------- 25 Fire Alarm 8.1.
-
Page 7: Chapter 1: Introduction
1. Devices (To) Chapter 1: Introduction 1. Zone 1. WL. Register 1. By Code Learn 2. By Code Input 1. Clear Single 2. Clear WL. Introduction: 3. Set zone Type 2. Clear All Nowadays, homeowners want much more than a monitored security system. They prefer an alert system. 4. -
Page 8: Chapter 3: Hardware Layout
7. Service 1. Set Time/Date Chapter 3: Hardware Layout 1. Auto Time 1 2. Auto Arm/Disarm 2. Auto Time 2 3.Call back when arm/dis. 3. Auto Time 3 The aim of this section is to acquaint you with the various circuit boards that make up the system. 4. -
Page 9: Power Supply Board
3.2 Power Supply Board Require for installer code 1. Cancel Alarm Requre for master code It supplies power for main board and GSM module. Pls cut off the power, with both AC and DC power off 2. Stop. Comm. Cable interface for power, connect with power supply board 3. -
Page 10: Chapter 4: System Installation
Appendix 2：Menu Structure Chapter 4: System Installation Description Abbreviation Temp. Temporary 4.1 Pre-installation Planning Trb. Trouble Auto Time Auto Arm/DisarmTime Before starting the installation procedure, it is worthwhile to draw a rough sketch of the building and Wireless determine the required position for the control panel and each wireless device. When deciding on the Comm. -
Page 11: Installation Procedure
Appendix 1：System Default Parameters steel reinforced concrete wall Setting Item Parameter Default 4-6 digits 0808 Master Code 4-6 digits 1234 Installer Code 4-6 digits 0809 Duress Code Wired zone 21&22 bypass Zone Bypass Send SMS option Send for alarm only brick wall Auto Arm/Disarm Bell call Back... -
Page 12: Power Off And Insert Sim Card
4.3.2 Power off and Inser t SIM Card Chapter 12: War ranty and Limitations SIM card must be inserted for GSM or SMS alarm via GSM module. The AC power and battery must be cut- Although it is an advanced and reliable security system, it does not offer absolute guaranteed protection off for safe operation. - Page 13 2. AUX Power Output Terminal 10.3 GSM Module AUX supplies power output for wired detectors(AC Operated: 10-12V, Battery Operated: 6-8V, max ● GSM working frequency: EGSM900/1800 current: 100mA. It may cause abnormal working for wired detector under low battery). ● RX sensitivity: ＜-106dB ●...
-
Page 14: Power Connection
◆Service info send to CMS by SMS For N/C detector: For N/O detector: ID:1234 N/C detector Zone: 002 362700002 Event: Service N/O detector 3627 means the CID exit PROG, 002 means the operator code. 2010/04/10 19:12:17 Figure -9- Figure -10- Chapter 10: Parameters 4.3.4 Power Connection 10.1 Specifications:... -
Page 15: Register Transmitters
◆“Arm/Disarm Query”: 4.3.5 Register Transmitters Transmitters refer to wireless devices such as detector, magnetic switch, siren and keyfob, etc. Only after Password0808Status enrolling can transmitters be recognized by the control panel. To register a device: 1. During disarm, press “PROG”. With voice guide “Enter password before setting parameters!”. Input the installer code with “#”. -
Page 16: Chapter 5: Operations
◆“Arm away”: At first, stick “Installing Hole Drawing” on the location for control panel. Drive 4 screws on the fixed position ID: 1234 (see Figure 11-1), and then hang the control panel directly on the screws(see Figure 11-2). While driving Prog: Arm away Act:OK the screws, please pay strict attention to the depth of screws to make sure easy hang and tamper switch... -
Page 17: Status Led
5.1.1 Status LED Pressing any key on control panel or phone during voice play may cause communication error. It Power LED: Red means AC loss or low battery. Green means normal. is suggest to operate after voice. If the system is under programming, remote programming is not Note available. -
Page 18: Display Interface
Clear Users standby mode, system status, time and date, or Arm Away Clear User Codes deletes all programmed user codes and restores the default master and installer banner are displayed on LCD. If system status is codes and duress codes. abnormal, it will displayed as: To clear users: 2 0 / 1 2 / 2 0 1 0... - Page 19 Alarm Display: AC Power off Delay(M) The alarm will display with voice guide in the alarm List. Press the navigation key to select with “#” to The AC Loss Delay is the amount of time that has to elapse before an AC Loss report is sent to the central station.
-
Page 20: Alarm Type And Way
5.3 Alar m Type and Way Activated by…… Disactivated…… PGM Trigger Zone 16 Alarm See above See above There are two alarm type: instant alarm and delay alarm. Zone 17 Alarm See above See above Trigger 24-hour zones, instant alarm will occur. Zone 18 Alarm See above See above... -
Page 21: Keypad Lock And Unlock
5.4 Keypad Lock and Unlock To set exit delay: 1. From the main menu, select “ Programming”→ “ #” → “ System Option”→ “ #” → “ Exit Delay(S)” → “ #” . If the code is input wrong, the voice will guide “Wrong code, please re-input!” and the LCD displays as: 2. -
Page 22: System Trouble Query
Dial Back “PROG” in main menu Code Type Arm&disarm Enter PROG Code Set Editable Clearable RP dial back is a security feature that helps ensure that remote programming is only performed by User code 2 authorized personnel. When the Remote Programmer contacts the panel, the panel hangs up and calls the User code 3 Callback telephone number. -
Page 23: Chapter 6: Zone Descriptions
For detailed system trouble and solution, please refer to following table: To set call attempts: 1. From the main menu, select “Programming”→ “#”→“Comm. ”→ “#”→ “Comm. Option”→ “#“→ “Call Attempts” Description Trouble Solutions → “#”. Low Battery Low power of battery Check the power connection timely. -
Page 24: Zone Type
Control Panel ID 6.1 Zone Type iID address can be set for each control panel so that the CMS can identify. Different ID must be set for different control panels, which is 4-8 digits utmost with default as 1234. Valid or not Valid or not Exit Entry... -
Page 25: Chapter 7 : Arm/Disarm Operation
To send for alarm: Chapter 7: Ar m/Disar m Operation 1. From the main menu, select “Programming”→“#”→“Comm.”→“#”→“Comm. Account” →“#”. 2. Press the navigation key to select CMS 1 or 2, ending with “#”. Then press the navigation key to select “Event Option”... -
Page 26: Arm Stay
To set siren cut-off: 1. From the main menu, select “Programming”→“#”→“Device”→“#”→“Siren”→“#”→“Siren Cut-off(M)”→“#”. Arm Away 2. Input the period “0-30minutes”. 3. Press “#” to exit. 2 0/ 1 2 / 2 0 1 0 1 5 : 3 0 Wireless Zone Supervision Wireless devices will transmit supervision signal to the control panel at intervals. -
Page 27: Chime Zone
2. If under arm away, and with no alarm, press “Arm stay” on keypad, the voice will guide “Enter password 2. Use the navigation key to select the zone ending with “#”. before setting parameters!” You can enter arm stay status with code input or direct keyfob operation. 3. -
Page 28: Arm/Disarm Via Phone
7.2 Ar m/Disar m via Phone 1. WL. Zone1 1. By Code Learn 1. WL Zone 1 1.WL. Zone 1 Registered! It enables you to arm or disarm via telephone(DTMF). For details, pls refer to 9.1 “Telecontrol via Phone”. Save? Zone ID: 2. -
Page 29: Chapter 8: Programming
Version Chapter 8: Programming It enables you to query the version of the control panel. To query the version of panel: 8.1 Access Programming 1. From the menu, select “Service” → “#” → “Version”→ “#”. 2. The panel version will display. Press “*” to quit . 1. -
Page 30: Entry/Exit Alarm 8.3.2. Stop Communication
With faulty operation or unexpected alarm occurs, user can “Cancel Alarm” in the menu. Thus the panel WL. Zone 3 Keyfob 1 Type: Entry/Exit will issue a event cancel to CMS Low Battery Activate Siren To cancel alarm: Low Battery →... - Page 31 Siren Test Note : The default master code is 0808, which is strongly recommended to edit after installation. Siren test is strongly recommended periodically for safety, which includes wired siren, wireless siren and built-in siren. Installer Code Set To test siren: The Installer code grants access to the Programming menu and the Service menu.
-
Page 32: Gas Alarm 8.3.4 Zone Bypass
8.3.7 Ser vice Option Set Time/Date Time and date must be set, or else the event log will be recorded with no time, arm or disarm may not be The default duress code is 0809 which is strongly recommended to edit after installation. realized, or system trouble will happen, voice guide will not work. -
Page 33: Ac Power Failure 8.3.5. Phone Set
Voice Phone Interface Set 1. Bypass one by one 2. WL. Zone 2 1. WL. Zone 1 It enables you to select PSTN or GSM as dialling way. 2. WL. Zone 2 To set voice phone interface: 1. From the main menu, select “Phone Set” → “#” → “Voice Phone Set” → “#”. 3.