Dynamite 70A Waterproof Sensorless Brushless Esc - Vaterra Hälix RTR Monster Truck Owner's Manual

DynamiTe 70a waTerproof sensorless brushless esC

eSc led StatuS
»
No ESC LEDs will glow when there is
no throttle input from the transmitter.
»
The red ESC LED glows when there is
any throttle input from the transmitter.
audiBle WarninG toneS
1 input voltage: The ESC checks the
input voltage when it is powered ON.
If a voltage problem is detected, the
ESC continuously sounds 2 beeps
with a 1 second pause (xx-xx-xx).
Power OFF the ESC and ensure the
connections are secure and that
the battery power is not too low
for safe operation.
2 radio connection: The ESC checks
radio signal input when it is powered
ON. If a problem is detected, the ESC
continuously sounds 1 beep with a 2
second pause (x--x--x). Power OFF
the ESC and ensure the radio
system is operating correctly.
eSc caliBration Procedure
Ensure proper ESC function by calibrat-
ing the ESC to your transmitter inputs.
Power OFF the ESC.
1
2 Ensure your transmitter is powered
ON, the throttle is not reversed, the
throttle trim is neutral and the
throttle travel range is at 100%.
3 Press the SET button while powering
ON the ESC. Release the button as
soon as the green LED starts to flash.
4 Calibrate the throttle points by
pressing the SET button once
after each step.
•
neutral Leave the throttle
(1 flash) at rest, untouched
•
full throttle Pull the throttle
(2 flashes) fully back
•
Push the throttle
full brake/
fully forward
reverse
(3 flashes)
5 The motor vibrates for 3 seconds
after the last step is completed.
eSc functionS and ModeS
The ESC includes programming
options so you can adjust the way your
vehicle performs. Refer to the included
settings table to adjust the ESC for
your driving conditions.
/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
eSc ProGraMMinG Procedure
Programming is accomplished using
the SET button on the ON/OFF switch.
Programming the eSc
1 Connect a fully charged battery
to the ESC.
2 Power ON the ESC.
3 Hold the SET button for 1 second
until the green LED blinks, then
release the SET button to enter
programming mode.
4 Press and release the SET button
as needed to get to the desired
menu option (the green LED will
blink corresponding to the menu
item number).
5 When at the desired menu item,
hold the SET button for 3 seconds
until the red LED blinks.
6 Press the SET button to move among
the settings based on how many
times the red LED blinks (Refer
to the table for more information).
7 Save the setting by holding the
SET button for 3 seconds.
8 Power OFF the ESC and repeat
the instructions above to change
other settings.
Tip: If desired, the ESC programming
can be returned to default settings
by powering ON the ESC and holding
the SET button for 5 seconds.
tecHnical SPecificationS
type
Sensorless/Waterproof
constant/Peak
70A/290A
resistance
0.0012 Ohms
function
Forward Only with Brake
Forward/Reverse with Brake
operation
Proportional forward,
proportional reverse with braking delay
Battery type/ input Voltage
2–3 cell Li-Po/Li-Fe or
4–9 cell Ni-MH/Ni-Cd
Bec output
6V/3A
overload Protection
Thermal
dimensions (lxWxH)
1.24 x 1.08 x 1.30 in
(31.5 x 27.5 x 33mm)
Weight
2.61 oz (74 g) with wires
noTiCe: Always disconnect the
battery from the ESC when you have
finished operating your vehicle. The
ESC's switch only controls power
to the receiver and servos. The ESC
will continue to draw current when
connected to the battery, resulting
in possible damage to the battery
through over-discharge.
EN