Download Print this page

Advertisement

Safety Information

Read the operating instructions for the unit and all other com-
ponents of your car audio system carefully before using the
system. They contain instructions about how to use the sys-
tem in a safe and effective manner. Panasonic assumes no
responsibility for any problems resulting from failure to
observe the instructions given in this manual.
This pictograph intends to alert you to the pres-
ence of important operating instructions and
installation instructions. Failure to heed the
Warning
instructions may result in severe injury or death.
Warning
Observe the following warnings when using
this unit.
❑ The driver should neither watch the display nor
operate the system while driving.
Watching the display or operating the system will distract
the driver from looking ahead of the vehicle and can cause
accidents. Always stop the vehicle in a safe location and use
the parking brake before watching the display or operating
the system.
❑ Use the proper power supply.
This product is designed for operation with a negative
grounded 12 V DC battery system. Never operate this prod-
uct with other battery systems, especially a 24 V DC battery
system.
❑ Keep batteries and insulation film out of reach of
infants.
Batteries and insulation film can be ingested, so keep them
out of the reach of infants. If an infant ingests a battery or
insulation film, please seek immediate medical attention.
❑ Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
❑ Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair the
product yourself. If the product needs to be repaired, consult
your dealer or an authorized Panasonic Servicenter.
❑ Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an
abnormal state (has foreign objects in it, is exposed to
water, is smoking, or smells), turn it off immediately and
consult your dealer.
❑ The remote control unit should not lie about in the
car.
If the remote control unit lies about, it could fall on the floor
while driving, get wedged under the brake pedal, and lead to
a traffic accident.
❑ Refer fuse replacement to qualified service person-
nel.
When the fuse blows out, eliminate the cause and have it
replaced with the fuse prescribed for this unit by a qualified
service engineer. Incorrect replacement of the fuse may lead
to smoke, fire, and damage to the product.
2
CQ-C7413U/C7113U
This manual uses pictographs to show you how to use the
product safely and to alert you to potential dangers resulting
from improper connections and operations. The meanings of
the pictographs are explained below. It is important that you
fully understand the meanings of the pictographs in order to
use this manual and the system properly.
This pictograph intends to alert you to the pres-
ence of important operating instructions and
installation instructions. Failure to heed the
Caution
instructions may result in injury or material dam-
age.
Observe the following warnings when
installing.
❑ Disconnect the lead from the negative (–) battery
terminal before installation.
Wiring and installation with the negative (–) battery terminal
connected may cause electrical shock and injury due to a
short circuit.
Some cars equipped with the electrical safety system have
specific procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY
SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND
PERSONAL INJURY OR DEATH.
❑ Never use safety-related components for installa-
tion, grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank,
brake, suspension, steering wheel, pedals, airbag, etc.) for
wiring or fixing the product or its accessories.
❑ Installing the product on the air bag cover or in a
location where it interferes with airbag operation is
prohibited.
❑ Check for piping, gasoline tank, electric wiring, and
other items before installing the product.
If you need to open a hole in the vehicle chassis to attach or
wire the product, first check where the wire harness, gaso-
line tank, and electric wiring are located. Then open the hole
from outside if possible.
❑ Never install the product in a location where it inter-
feres with your field of vision.
❑ Never have the power cord branched to supply other
equipment with power.
❑ After installation and wiring, you should check the
normal operation of other electrical equipment.
The continuation of their using in abnormal conditions may
cause fire, electrical shock or a traffic accident.
❑ In the case of installation to an airbag-equipping
car, confirm warnings and cautions of the vehicle
manufacturer before installation.
❑ Make sure the leads do not interfere with driving or
getting in and out of the vehicle.
❑ Insulate all exposed wires to prevent short circuit-
ing.

Advertisement

   Also See for Panasonic CQ-C7413U? CQ-C7113U

   Related Manuals for Panasonic CQ-C7413U? CQ-C7113U

   Summary of Contents for Panasonic CQ-C7413U? CQ-C7113U

  • Page 1: Safety Information

    They contain instructions about how to use the sys- from improper connections and operations. The meanings of tem in a safe and effective manner. Panasonic assumes no the pictographs are explained below. It is important that you responsibility for any problems resulting from failure to fully understand the meanings of the pictographs in order to observe the instructions given in this manual.

  • Page 2

    For maximum safety, have it installed by your dealer. If any part of your body or clothing comes into contact with Panasonic is not liable for any problems resulting from your battery liquid, wash it with plenty of water. ●...

  • Page 3: Before Reading These Instructions

    REFER SERVICING TO QUALIFIED PERSONNEL. Before Reading These Instructions Panasonic welcomes you to our constantly growing family of electronic products owners. We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and assembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours of enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family.

  • Page 4

    Before Reading These Instructions XXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXX XXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX OO-OOOOO OO-OOOOO Operating System Upgrade Installation Owners Instructions Guidebook Instructions Information Card (YEFM285772) (YEFM262689) (YEFM294127) Instruction kit Q'ty: 1 set POWER SOURCE MENU BAND BAND BAND MUTE MUTE MUTE RANDOM SCAN...

  • Page 5

    833-8855 Accessory Purchases: Link : “Servicentres locator” under “Customer sup- Purchase Parts, Accessories and Instruction Books port” online for all Panasonic Products by visiting our Web Site at: http://www.pasc.panasonic.com Panasonic Factory Service: or, send your request by E-mail to: Vancouver Toronto npcparts@panasonic.com...

  • Page 6

    United States or Puerto Rico. This warranty is extended only to the original purchaser of a new product which was not sold Panasonic Canada Inc. warrants this product to be free from defects in materials and workmanship and agrees to remedy any such defect “as is”.

  • Page 7: Features

    ( page 32) ¡ DVD Changer The optional adapter (Conversion Cable for DVD/CD * This software is downloadable from Panasonic Web site Changer: CA-CC30U) allows you to connect the option- (http://panasonic.co.jp/pas/en/software/customize/index.html) al Panasonic DVD changer unit (CX-DH801U). ¡...

  • Page 8: Table Of Contents

    Contents English Français Español Safety Information ¡ Before Reading These Instructions ¡ Features ¡ Controls Layout ¡ Preparation (Clock adjustment etc.) ¡ General ¡ Sound Control ¡ Radio ¡ CD Player ¡ MP3/WMA Player ¡ Audio Setting ¡ Function Setting (Security Function Setting etc.) ¡...

  • Page 9: Controls Layout

    Controls Layout Note: This instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded) VOLUME page 15) PUSH SEL Select page 28) MENU page 29, 30) page 18) SRS WOW y / 5 Pause/Play u (eject) TILT page 15) TUNE...

  • Page 10: Number Buttons

    Number Buttons – 0 to 9 VOL Volume SEL Select }:Up MENU {:Down Number NUMBER POWER SRC (SOURCE) RANDOM RANDOM POWER SOURCE MENU SCAN SCAN BAND BAND BAND BAND MUTE MUTE MUTE MUTE Pause/Play SBC-SW Super Bass REPEAT REPEAT RANDOM SCAN REPEAT Control-Subwoofer...

  • Page 11: Preparation (clock Adjustment Etc.)

    Stick your thumbnail into the groove, and push the Note: Battery Information: holder in the direction of Battery Type: Panasonic lithium battery (CR2025) the arrow, and at the (Included in the remote control) same time. Battery Life: Approximately 6 months under normal use...

  • Page 12

    The following functions are activated when the Security ¡ The alarm sounds and the message appears on the Function is ON. page 29) screen to warn you to remove the face plate at ACC off. ¡ The security indicator lights up when removing the face plate.

  • Page 13: General

    General This chapter explains how to turn on or off the power, how to adjust the volume, etc. Power on Press [SRC] (PWR: Power). Power off Hold down [SRC] (PWR: Power) until you hear a beep, then release it. You can remove the face Mounting plate to prevent it from being stolen.

  • Page 14

    Open/Eject Press [u] (OPEN). When a disc is already loaded, the disc will automatically be ejected. Tilt Cautions: The display angle changes among 4 levels as follows ¡ To avoid damaging the face plate, do not push it every time you hold down [u] (TILT) for 1 sec. or down or place objects on it while it is open.

  • Page 15

    General The source changes as follows every time [SRC: Source] is pressed. Radio System-up Connector FM1, FM2, FM3, AM page 20) Device connected to the System-up Connector of this unit When optional devices are connected: Shift to connected devices When an expansion module is connected: The devices connected to the ports 1 to 4 are activated in sequence after shifting to AUX2 (devices connected to the AUX terminal of the expansion module).

  • Page 16

    The display changes as follows every time [D] (DISP: DISPLAY) is pressed. Note: The graphic pattern and still image are selectable. page 31) At power-on: Mode Display OFF All displays disappear in 5 seconds. Folder hierarchy (MP3/WMA mode only.) Ordinary display + clock Ordinary display + graphic pattern Only still image Only graphic pattern...

  • Page 17: Sound Control

    Sound Control Only for CQ-C7413U SRS WOW is 3-D sound technology based on the HRTF (Head Related Transfer Function) theory. Unlike conventional audio systems, “natural 3-D sound field”, “rich bass”, and “crisp and clear sound” can be obtained at the same time in a wide area in front of speakers. Holding down [VOLUME] (SRS WOW) for 2 sec.

  • Page 18

    The equalizer curve is selectable from among preset 6 types (FLAT, ROCK, POP, VOCAL, JAZZ, and CLUB) depending on your listening category. Note: SQ is not changeable when SRS WOW is enabled. page 18) SQ changeover The SQ category is changed every time [SQ] (Sound Quality) is pressed.

  • Page 19: Radio

    Radio This chapter explains how to listen to the radio. Press [SRC] (Source) to select the radio mode. Press [BAND] to select a band. Select a station. Frequency adjustment []] (TUNE): Lower [[] (TUNE): Higher Note: Hold down for 0.5 sec. or more and release for station search.

  • Page 20

    Up to 6 stations can be preset in AM, FM1, FM2, and FM3 Manual station preset respectively. Preset stations can be simply called up by pressing [}] Tune in to a station. (P·SET) or [{] (P·SET). Hold down [}] or [{] for 2 sec. or Notes: more.

  • Page 21: Cd Player

    CD Player When a disc is already loaded, press [SRC] (Source) to select the CD mode. Press [u] (TILT) (OPEN) to open the face plate. When a disc is already loaded ( lights), the disc will automatically be ejected. Load a disc with the printed side facing Select a desired portion.

  • Page 22: Scan Play

    Cautions: ¡ This unit does not support 8 cm (3”) discs. ¡ Refer to the section on “Notes on CD/CD Media (CD-ROM, ¡ Do not use irregularly shaped discs. page 38) CD-R, CD-RW)” page 38). ¡ Do not use discs that have a seal or label attached. ¡...

  • Page 23: Mp3/wma Player

    MP3/WMA Player When a disc is already loaded, press [SRC] (Source) to select the MP3/WMA mode. Press [u] (TILT) (OPEN) to open the face plate. When a disc is already loaded ( lights), the disc will automatically be ejected. Select a desired portion. Load a disc with the printed side facing Folder selection The face plate closes automatically, and the unit rec-...

  • Page 24

    Notes: ¡ Refer to the section on “Notes on MP3/WMA” page 26) ¡ This unit does not support a MIX mode CD (a CD containing both CD-DA and MP3/WMA data). In case of using such a CD, problems may occur such as anacoustic playback. Random and Repeat play can be set.

  • Page 25: Display Information

    MP3/WMA Player What is MP3/WMA? Display Information MP3 (MPEG Audio Layer-3) and WMA (Windows Media Displayed items Audio) are the compression formats of digital audio. The ¡ CD-TEXT ¡ MP3 (ID3 tag) former is developed by MPEG (Motion Picture Experts Disc title Album name Group), and the latter is developed by Microsoft...

  • Page 26

    Recording MP3/WMA files on a CD-media ¡ You are recommended to minimize the chances of ¡ The file extension “.mp3” or “.wma” should be making a disc that contains both CD-DA files and assigned to each file depending on the file format. MP3/WMA files.

  • Page 27: Audio Setting

    Audio Setting Adjustment to each speaker and an optional subwoofer Balance adjustment Press [VOLUME] (PUSH SEL: (Setting range: L (left)15 to R (right) 15 and Center, Default: Center) Select) to display q : Right enhanced the AUDIO menu w : Left enhanced display.

  • Page 28: Function Setting (security Function Setting Etc.)

    Function Setting Adjustment to display on the FUNCTION menu MUTE KEY Press [MENU] to display the menu dis- play. Setting [MUTE] buttons’ functions Volume off (default) For using the remote control, hold down Volume down by 10 steps [SEL] (MENU) for 2 sec.

  • Page 29: Display Setting

    Display Setting Adjustment to display on the DISPLAY menu COLOR Press [MENU] to display the menu display. (Setting range: 10 types, default: STORM) The illumination color changes as follows. For using the remote control, hold down Switching by [}] or [{] [SEL] (MENU) for 2 STORM: The color varies in conjunction with time.

  • Page 30

    CUSTOM ADJ CONTRAST (Setting range: 0 to 100, default: R50, G50, B50) (Setting range: 1 to 5, Default: Contrast 3) [[]: You can adjust each color. Tilting up view angle []]: Tilting down view angle []][[]: RGB selection [}][{]: Adjustment (0 to 100) CLOCK ADJ SCREEN Note: Adjust the clock when “ADJUST”...

  • Page 31: Customize The Display (customize Function)

    You can edit the moving images and still images that are initially stored in the unit. You also can use the data that is downloaded from the Panasonic Web site and the data that is stored with a digital camera or other devices and processed with exclusive software, IMAGE STUDIO.

  • Page 32

    In such further information. a case, try customizing again. ¡ The default image exists on the Panasonic Web site. If Panasonic Web site: you would like to restore it, download the image from (http://www.panasonic.co.jp/global/) the site.

  • Page 33: Troubleshooting

    If the described suggestions do not solve the problem, it is example, without sound, or with smoke or a foul recommended to take the unit to your nearest authorized Panasonic smell, which can cause ignition or electric shock. Servicenter. The product should be serviced only by qualified personnel.

  • Page 34

    The power fails The safety device works. unintentionally. Consult your dealer, or your nearest Panasonic Servicenter. Antenna installation or wiring of antenna cable is faulty. Check whether the antenna mounting position and its wiring are correct. In addition, check to see whether the antenna ground is securely connected to Poor reception or the chassis.

  • Page 35

    Troubleshooting Problem Possible cause Possible solution The disc is inserted upside down. Insert a disc correctly. No playback or disc ejected There is a flaw or foreign material on the disc. Remove the foreign material, or use a flawless disc. Sound skipping or There is a flaw or foreign material on the disc.

  • Page 36: Error Display Messages

    Problem Possible cause Possible solution The battery is inserted in the wrong direction. A wrong battery is inserted. aInsert a correct battery in the correct direction. The battery is weak. aReplace the battery with new one. No response to The aiming direction of the remote control unit is wrong. pressing buttons aAim the remote control unit at the sensor of the unit and press buttons.

  • Page 37: Notes On Discs

    Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for routine exterior cleaning. Never use benzine, thinner, or other solvents. If the fuse blows out, consult your dealer, or your nearest authorized Panasonic Servicenter. Warning ¡...

  • Page 38: Specifications

    Specifications Power Supply DC 12 V (11 V – 16 V), Test Voltage 14.4 V, Negative Ground Tone Controls (Bass/Treble) Bass; ±12 dB at 60 Hz, Treble; ±12 dB at 16 kHz Equalizer Center Frequency 60, 160, 400, 1 k, 3 k, 6 k, 16 k Hz (CQ-C7413U), Band 1 (60, 80, 100, 200 Hz), Band 2 (500, 1k, 2k, 3k Hz), Band 3 (10k, 12k, 15k, 18k Hz) (CQ- C7113U) Variable Range of Equalizer...

Comments to this Manuals

Symbols: 0
Latest comments: