Table of Contents
Advertisement
OYAMAHAe
YHT-24
QUICK-CONNECT GUIDE
OPERATING THE UNIVERSAL REMOTE CONTROL
3. Load a DVD (or LD) into the DVD (or LD) player.
4. Aim the remote control at the DVD (or LD) player,
and press> (forward button) to start play.
NOTE: The DVD player's controls are now assigned to
the remote control buttons, since DVD was the last
selected component.
3. Using the keypad, enter the code "0000".
4. The indicator LED will flash twice to confirm all
codes have been reset to factory values.
If
the lED
does not flash twice, repeat steps 1 through 3.
5. For your convenience, the following reference chart
lists the factory codes:
Component
Component
Code
Selector Button
RESETTING THE REMOTE CONTROL To fACTORY CODES
You can reset the remote control to factory codes for all
components or a desired component, as follows:
RESETTING CODES FOR ALL COMPONENTS
1.
Press any component selector button other than
AMP/TUNER.
2. Press and hold both VOLUME buttons at least four
seconds until the indicator LED flashes twice.
3. Using the keypad, enter the code "9990".
4. The indicator LED will flash twice to confirm all
codes have been reset to factory values.
If
the lED
does not flash twice, repeat steps 1 through 3.
RESETTING CODES FOR
A
DESIRED COMPONENT
1.
Press a component selector button that matches the
component you wish to reset to factory codes.
2. Press and hold both VOLUME buttons at least four
seconds until the indicator LED flashes twice.
0101
0006
0002
0008 Yamaha
0005 Yamaha
0024 Yamaha
TV
Cable TV
VCR
DVD player
CD player
MD recorder
TV
CBL/SAT
VCR
DVD/LD
CD
TAPE/MD
PLAYING
A
DVD
1. Aim
the remote control at the HTR-5440, press AMP /
TUNER to select the component, and then press
POWER to turn the receiver on. Press DVD/lD (i.e., 4
on the keypad) as the input for the receiver.
2. Press DVD /lD and then press POWER to turn the
DVD (or lD) player on.
NOTE: If the DVD player is plugged into the switched ac
outlet (on the back of the receiver) and its power switch
was already engaged, the unit will come on each time the
receiver
is
powered on.
OVERVIEW
The universal remote control will control up to seven
different types of components (including the HTR-5440
receiver), each of which becomes active when you press
a selection (e.g., TV, VCR, etc.). We can only briefly
describe some functions here, and we encourage you
use the HTR-5440 Owner's Manual to gain additional
experience with this powerful unit.
PLAYING
A
VIDEOCASSETTE
1.
Aim the remote control at the HTR-5440, press
AMP /TUNER to select the component, and then
press POWER to turn the receiver on. Press VCR (i.e.,
6 on the keypad) as the input for the receiver.
2. Aim the remote control at the TV, press the TV to
select the component, and then press POWER to
turn the television on. Press TV INPUT (or A/B) to
select the correct input.
3. Aim the remote control at the VCR, press VCR to
select the component, and then press POWER to turn
the VCR on. Put a tape in the VCR, press PLAY.
NOTE: At this point, the VCR controls are assigned to the
remote control, since VCR was the last selected compo-
nent. If you now press the VOLUME up (down) buttons,
the TVNCR volume will be raised (or lowered). To adjust
the receiver's volume, you must press AMP/TUNER to
activate its functions.
_YAMAHA-
©2001 YAMAHA ELECTRONICS CORPORAnON, USA
6660 Orangethorpe Avenue, Buena Park, CA 90620
PH: (714) 522-9105; FAX: (888) 435-7922
http://www.yamaha.com
Advertisement
Table of Contents
